NO!!
Official Scangauge II Thread - Share your Data, Discuss Settings ,Problems, Findings!
183 posts · 124,309 views · page 3 of 4
Replies continued
The answer is Yes. When KM is selected for distance and Liters are selected on fuel measurement, the fuel economy will be reported as mentioned. (LHK)Originally Posted by leasaunce ↑question, can you change mpg to L/100km?? or mph to kph???
I found this info on page 14 as a note in the user manual.
My best run so far with this tool was 46.63 MPG. 40%city 60%highway. I have raised the tire pressure by 3 or 4 psi. I would like to know what other tricks can be applied for better fuel economy.
so how do you put in custom codes? stil cant figure that out ive had mine for a while now
From main menu, select options as fallows.Originally Posted by Jerkratt ↑so how do you put in custom codes? stil cant figure that out ive had mine for a while now
1. MORE
2. SETUP
3. UNITS
From here you can change from MPH to KMH and so forth.
that i know those are not custom codes those are the display
Found this neat post on Scanguage Tips & Tricks by Dan over at CleanMPG. You need to check it out.
http://www.cleanmpg.com/forums/scan-...icks-5901.html
http://www.cleanmpg.com/forums/scan-...icks-5901.html
cool!!!!!!!!!!1
That's so cool! Thanks for the link. Its nice to get the insider view of it. And it sounds like the next one is going to be even better with more read outs! I hope they don't bump the price to high.
http://www.3n1autocomputer.com/groupbuy.html
Bump This offer is still valid; I did my order yesterday.
NOTE: In my hands 48 hours after I ordered it, installed and working in about 15 minutes.
Bump This offer is still valid; I did my order yesterday.
NOTE: In my hands 48 hours after I ordered it, installed and working in about 15 minutes.
The only complaint I have of the ScanGauge II is that when the car is in DFCO mode (search this term if you don't know what it is), the ScanGuage II will not show GPH at zero. Anyone know otherwise?
thats maybe because DFCO doesnt exist... i still think its a myth..again others opinion differs..🤷Originally Posted by Pavel Olavich ↑The only complaint I have of the ScanGauge II is that when the car is in DFCO mode (search this term if you don't know what it is), the ScanGuage II will not show GPH at zero. Anyone know otherwise?
Oh, it's real, bruda....but I think it's more effective with manual trannies.Originally Posted by marcus ↑thats maybe because DFCO doesnt exist... i still think its a myth..again others opinion differs..🤷
pavel.. i really wanna believe it ,just to be honest with you..but i did my research in regards to "dfco"..not on a toyota history not even on makers of vvti engine.. where did this come from?. who started it ? and how come scangauge2 doesnt adjust to it when in use... 🤷 🤷 🤷Originally Posted by Pavel Olavich ↑Oh, it's real, bruda....but I think it's more effective with manual trannies.
i found this: it did exist but not the way it was presented..
Deceleration fuel cut-off:
"A device which stops the flow of fuel to the carburetor or injectors when the vehicle rapidly decelerates in the event of a crash thus preventing the possibility of a fire or explosion."
Well, I myself do not have any credible evidence that it does exists....I think the ScanGauge II is buggy, frankly. Not saying it is a bad product....on the contrary it's a great product, but it does have it's strangeness....but to the point of DFCO, I've tried a few tests of my own, as mentioned by BailOut, and I tend to think it does exist...but I could be wrong too...Originally Posted by marcus ↑pavel.. i really wanna believe it ,just to be honest with you..but i did my research in regards to "dfco"..not on a toyota history not even on makers of vvti engine.. where did this come from?. who started it ? and how come scangauge2 doesnt adjust to it when in use... 🤷 🤷 🤷
i found this: it did exist but not the way it was presented..
Deceleration fuel cut-off:
"A device which stops the flow of fuel to the carburetor or injectors when the vehicle rapidly decelerates in the event of a crash thus preventing the possibility of a fire or explosion."
Marcus, read this Toyota white paper on ECU stuff, pluse DFCO too (page 11). It is this paper that suggest that our Yaris does in fact have DFCO....
http://www.autoshop101.com/forms/h43.pdf
http://www.autoshop101.com/forms/h43.pdf
ya pavel i was just reading that earlier.. now is that for vvti for yaris and if dfco exist i still dont get how it works. do you down shift on higher revs so cut off last longer or what...?? well im now much of a believer then again i always down shift to slow down anyways so in a way i have been using the what so called "DFCO"...Originally Posted by Pavel Olavich ↑Marcus, read this Toyota white paper on ECU stuff, pluse DFCO too (page 11). It is this paper that suggest that our Yaris does in fact have DFCO....
http://www.autoshop101.com/forms/h43.pdf
lets get back to scangauge 2... whan is scangauge3 coming out??🤷
The SGII cannot definitively show a DFCO mode because there are no OBDII codes for fuel injection. As such, each manufacturer makes their own codes, and as of today they are proprietary.
I'm not sure why anyone would doubt the existence of DFCO. It's not science fiction. It is documented in many places, and can be tested by any individual using what I outlined here. It's a simple concept, and whether a car has DFCO or not is highly obvious when the test I outlined is performed on a vehicle that doesn't have it (when I tried it on my rental Aveo (I can't believe GM actually produced this car... no thought, no soul, no reliability, CELs at the drop of a hat, etc...) its AT immediately went into a protective mode, and when I tried it on our old Tacoma it was like driving through a meter of water).
There are even varying levels of DFCO. One of the rental cars I got stuck with when my Yaris' door was being repaired was a POS GMC Canyon pickup. It was a real PITA to drive down the mountain because (aside from handling like an overweight marshmallow that would understeer or oversteer but never rail a turn) it took like 3 or 4 seconds of engine braking to start DFCO, but only half of the 6 cylinders. Then, after 8 - 10 seconds more, it would shut the rest of them off. It made for some rather unpredictable but inevitable engine braking.
I'm not sure why anyone would doubt the existence of DFCO. It's not science fiction. It is documented in many places, and can be tested by any individual using what I outlined here. It's a simple concept, and whether a car has DFCO or not is highly obvious when the test I outlined is performed on a vehicle that doesn't have it (when I tried it on my rental Aveo (I can't believe GM actually produced this car... no thought, no soul, no reliability, CELs at the drop of a hat, etc...) its AT immediately went into a protective mode, and when I tried it on our old Tacoma it was like driving through a meter of water).
There are even varying levels of DFCO. One of the rental cars I got stuck with when my Yaris' door was being repaired was a POS GMC Canyon pickup. It was a real PITA to drive down the mountain because (aside from handling like an overweight marshmallow that would understeer or oversteer but never rail a turn) it took like 3 or 4 seconds of engine braking to start DFCO, but only half of the 6 cylinders. Then, after 8 - 10 seconds more, it would shut the rest of them off. It made for some rather unpredictable but inevitable engine braking.
I tend to agree with you, however I don't see a need for a special code to signify DFCO, because if DFCO is in process, then the injectors are no longer feeding gas, so then the GPH should be zero, yea? I've got an auto tranny in my Yaris, by the way, and I think DFCO works in conjunction with the grade logic, and torque converter lock up processes, but I can't be so sure. Yet.Originally Posted by BailOut ↑The SGII cannot definitively show a DFCO mode because there are no OBDII codes for fuel injection. As such, each manufacturer makes their own codes, and as of today they are proprietary.
I'm not sure why anyone would doubt the existence of DFCO. It's not science fiction. It is documented in many places, and can be tested by any individual using what I outlined here. It's a simple concept, and whether a car has DFCO or not is highly obvious when the test I outlined is performed on a vehicle that doesn't have it (when I tried it on my rental Aveo (I can't believe GM actually produced this car... no thought, no soul, no reliability, CELs at the drop of a hat, etc...) its AT immediately went into a protective mode, and when I tried it on our old Tacoma it was like driving through a meter of water).
There are even varying levels of DFCO. One of the rental cars I got stuck with when my Yaris' door was being repaired was a POS GMC Canyon pickup. It was a real PITA to drive down the mountain because (aside from handling like an overweight marshmallow that would understeer or oversteer but never rail a turn) it took like 3 or 4 seconds of engine braking to start DFCO, but only half of the 6 cylinders. Then, after 8 - 10 seconds more, it would shut the rest of them off. It made for some rather unpredictable but inevitable engine braking.
By the way, that POS Chevy Aveo is not made by Chevy....it's Korean (Kia or Hyundai)...it's a rebadged POS, for sure...it cost less then our Yaris, but the cost of ownership over 5 years is much more.
A bit off topic, but what kind of oil do you run? What is your change intervals?
Thanks!
The SGII's GPH reading isn't done directly from a flow meter or anything. It is inferred by your RPM, speed, and air flow. This is why you still see ~0.2 GPH when in DFCO... that's the closest the SGII can get according to its internal math as you're still producing high RPM.
Check your PMs for my oil metrics. I don't want to derail this thread. 😉
Check your PMs for my oil metrics. I don't want to derail this thread. 😉
I bought the scangauge II and tried plugging it into my 2007 Yaris MT. I had the key ON and also tried with the engine running, but all i got was "Connecting...." and never quite connected. I would like to know if anyone has had this problem.
Thanks
Thanks
I was under the impression that the GPH value was input to the ScanGauge II via the ODB port, and not calculated by it....I certainly could be wrong however. 😕Originally Posted by BailOut ↑The SGII's GPH reading isn't done directly from a flow meter or anything. It is inferred by your RPM, speed, and air flow. This is why you still see ~0.2 GPH when in DFCO... that's the closest the SGII can get according to its internal math as you're still producing high RPM.
Check your PMs for my oil metrics. I don't want to derail this thread. 😉
I've never seen this issue but I would try re-seating the OBDII connector as it sounds like it might not be a solid connection.Originally Posted by dawasherpa ↑I bought the scangauge II and tried plugging it into my 2007 Yaris MT. I had the key ON and also tried with the engine running, but all i got was "Connecting...." and never quite connected. I would like to know if anyone has had this problem.
Thanks
If it still doesn't work then I'd try completely disconnecting everything for an hour or so, then hooking it back up and immediately starting the engine. This will give it the best chance for making that initial connection.
If it still doesn't work at that point you should take your car to a local shop and ask them to hook their reader up, just to see if theirs works or not. If it does you know you have a bad SGII and you can RMA it. If it doesn't you know you need to take the Yaris to the dealership to get the OBDII port working.
Reseating the connector did not work. To make sure SG II wasn't the problem, I hooked it up to Dodge Neon of my friends and it worked fine. So, now I know it's the Yaris's OBDII connector. I have scheduled a appointment to look into it, although they were telling me that the SGII may not be compatible with Yaris. But I know SGII is compatible as you guys have it working for you. So, we'll see what the problem is.Originally Posted by BailOut ↑I've never seen this issue but I would try re-seating the OBDII connector as it sounds like it might not be a solid connection.
If it still doesn't work then I'd try completely disconnecting everything for an hour or so, then hooking it back up and immediately starting the engine. This will give it the best chance for making that initial connection.
If it still doesn't work at that point you should take your car to a local shop and ask them to hook their reader up, just to see if theirs works or not. If it does you know you have a bad SGII and you can RMA it. If it doesn't you know you need to take the Yaris to the dealership to get the OBDII port working.
Thanks
Turns out, I got a bad Scangauge. The company was nice enough to exchange it for a new one, which worked right away.Originally Posted by dawasherpa ↑Reseating the connector did not work. To make sure SG II wasn't the problem, I hooked it up to Dodge Neon of my friends and it worked fine. So, now I know it's the Yaris's OBDII connector. I have scheduled a appointment to look into it, although they were telling me that the SGII may not be compatible with Yaris. But I know SGII is compatible as you guys have it working for you. So, we'll see what the problem is.
Thanks
Thanks
on my yaris scan gauge says open loop any time i take my foot off the gas pedal as soon as I give it gas it say closed loop this is all the time not just when the engine is cold is this normal?
Edit 9/18/07, additions/corrections
Yes, it's normal. In fact it's our DFCO indication for the Yaris. Here's why:
DFCO is by definition, an Open Loop condition, because it's a fuel cutoff. Closed loop is when the computer is using signals from various sensors to meter how much fuel to inject. At the same time, the amount of fuel injected is one of the things that creates the conditions that determine what the signals will be from those sensors. In other words, it's a closed control loop. DFCO overrides this and cuts off the fuel injectors.
If you see Open Loop any other time, except briefly after a cold start, or briefly if you're drag racing or under very heavy load like climbing a steep hill, then something is probably wrong and most likely the check engine light will come on....and a trouble code will be waiting for the scanner function of the scangauge to read.
If you were driving a manual transmission, you'd find it will also switch back to Closed Loop when the engine speed drops below about 1000RPM with it in gear and your foot is off the gas pedal. At the same time you'd feel a very slight surge of power. That's DFCO switching out to keep the motor from stalling. Then you'd quickly have to stomp on the clutch and throw it into neutral, or into low gear and go....or it'll stall anyway.
On the other hand, scangauge fuel consumption calculation is unaware of DFCO, so it registers higher consumption than if you were in neutral. In my case, this helps offs offset consumption error calculation in the other direction.
I have a 96 Chevy conversion van which sat with a dead transmission and engine problems for 2 years. I've been reviving it this summer....the SG came in really handy diagnosing....and I was surprised to find it too, has DFCO.
Yes, it's normal. In fact it's our DFCO indication for the Yaris. Here's why:
DFCO is by definition, an Open Loop condition, because it's a fuel cutoff. Closed loop is when the computer is using signals from various sensors to meter how much fuel to inject. At the same time, the amount of fuel injected is one of the things that creates the conditions that determine what the signals will be from those sensors. In other words, it's a closed control loop. DFCO overrides this and cuts off the fuel injectors.
If you see Open Loop any other time, except briefly after a cold start, or briefly if you're drag racing or under very heavy load like climbing a steep hill, then something is probably wrong and most likely the check engine light will come on....and a trouble code will be waiting for the scanner function of the scangauge to read.
If you were driving a manual transmission, you'd find it will also switch back to Closed Loop when the engine speed drops below about 1000RPM with it in gear and your foot is off the gas pedal. At the same time you'd feel a very slight surge of power. That's DFCO switching out to keep the motor from stalling. Then you'd quickly have to stomp on the clutch and throw it into neutral, or into low gear and go....or it'll stall anyway.
On the other hand, scangauge fuel consumption calculation is unaware of DFCO, so it registers higher consumption than if you were in neutral. In my case, this helps offs offset consumption error calculation in the other direction.
I have a 96 Chevy conversion van which sat with a dead transmission and engine problems for 2 years. I've been reviving it this summer....the SG came in really handy diagnosing....and I was surprised to find it too, has DFCO.
ScanGauge gives by the abbreviaton "MAP" no value ( Yaris 1.8 TS)
Can someone tell me whether that is normal?
Has the Yaris no sensor for the "MAP" value?
Thanks
Can someone tell me whether that is normal?
Has the Yaris no sensor for the "MAP" value?
Thanks
Correct MAP and FPR both don't display as the ECU won't give a value.Originally Posted by andries ↑ScanGauge gives by the abbreviaton "MAP" no value ( Yaris 1.8 TS)
Can someone tell me whether that is normal?
Has the Yaris no sensor for the "MAP" value?
Thanks
Where is the best place to buy a ScangaugeII nowadays? I thought I saw something
before the hack about a group buy?? or one of our vendors ?? 🤷
before the hack about a group buy?? or one of our vendors ?? 🤷
from me. I cannot advertise my price due to manufacturer restrictions, but...
.... I'll be so HAPPY to receive your PM 👍
.... I'll be so HAPPY to receive your PM 👍
It's a Daewoo rebadged to a ChevyOriginally Posted by Pavel Olavich ↑I tend to agree with you, however I don't see a need for a special code to signify DFCO, because if DFCO is in process, then the injectors are no longer feeding gas, so then the GPH should be zero, yea? I've got an auto tranny in my Yaris, by the way, and I think DFCO works in conjunction with the grade logic, and torque converter lock up processes, but I can't be so sure. Yet.
By the way, that POS Chevy Aveo is not made by Chevy....it's Korean (Kia or Hyundai)...it's a rebadged POS, for sure...it cost less then our Yaris, but the cost of ownership over 5 years is much more.
A bit off topic, but what kind of oil do you run? What is your change intervals?
Thanks!
PM sent.Originally Posted by cali yaris ↑from me. I cannot advertise my price due to manufacturer restrictions, but...
.... I'll be so HAPPY to receive your PM 👍
I did the group buys a while back and I'm back as a vendor with ScanGauges a-plenty. Checkout the sponsored sales area for my posts. 👍Originally Posted by Revsson ↑Where is the best place to buy a ScangaugeII nowadays? I thought I saw something
before the hack about a group buy?? or one of our vendors ?? 🤷
Is it possible to change the $ sign into the € sign on a ScanGauge?
Not right now, you can do liters but the amount stays the same.Originally Posted by andries ↑Is it possible to change the $ sign into the € sign on a ScanGauge?
Originally Posted by 365Motorwerks ↑Not right now, you can do liters but the amount stays the same.
oke,thanks
I was researching scanguage on the internet and read that an owner was having problems with a Rostra cruise control and Scanguage. Apparently they both were getting their signal from the ECU and if the cruise was on scanguage wouldn't work. Cruise would work if Scanguage was turned off though. Has anyone else had this kind of experience? If this is a problem, is there a workaround?
Mileage...I am not getting anthing near 35 of above in mileage, with 32.655 bing my best early last fall. I'm driving conservatively....although most of my driving is in town. I am just over the 2000 mile mark, and am hoping that it will improve as mileage goes up. Of course I realize that the extra cold winter that we have had here in Southern Michigan has taken its toll!
I will be getting an oil change in the near future, maybe that will make a positive difference.
Mileage...I am not getting anthing near 35 of above in mileage, with 32.655 bing my best early last fall. I'm driving conservatively....although most of my driving is in town. I am just over the 2000 mile mark, and am hoping that it will improve as mileage goes up. Of course I realize that the extra cold winter that we have had here in Southern Michigan has taken its toll!
I will be getting an oil change in the near future, maybe that will make a positive difference.
I have an 08 with the dealer installed rostra cruise and my Scangauge works just fine.As for the crappy gas mileage it will get better as the temps heat up,snow tires come off and the gas gets reformulated to summer specs,on a trip last summer i was getting high 40'smpg highway,around town low 40's .
Welcome to the forum.
Welcome to the forum.
Scangauges are still in stock, and still at a price I can't advertise. PM if anyone is interested in one. 👍
Thanks Jambo101 for the quick response, it's appreciated. Maybe the rostra/scanguage conflict was a fluke, and not the norm!Originally Posted by jambo101 ↑I have an 08 with the dealer installed rostra cruise and my Scangauge works just fine.As for the crappy gas mileage it will get better as the temps heat up,snow tires come off and the gas gets reformulated to summer specs,on a trip last summer i was getting high 40'smpg highway,around town low 40's .
Welcome to the forum.
Got my Scangauge today. Thank you Micro Image for the great price and fast shipping. Folks, if you can.....shoot Garm a PM for the best deal out there bar none.
I ordered my Scangauge II today but I'm curious as to how it lights up? Does it automatically light when you turn the headlights on?
automatically lights up when turned on , then you can change the color to
what ever you want 👍
what ever you want 👍
Thanks!Originally Posted by 1NZYaris1 ↑automatically lights up when turned on , then you can change the color to
what ever you want 👍
Has anyone tried using the 'Blendmount' to install their Scangauge II above the rearview mirror? It looks like a pretty good idea, just not sure if it'll fit since there's not much clearance between the mirror and windshield. Their website doesn't say what vehicles it works with, so I'm curious if any Yarii owners have tried this.
http://www.blendmount.com/showthread.php?t=2
http://www.blendmount.com/showthread.php?t=2
Was going to but I like you believe there will be a fitment issue. I am working on some ideas now, none of which include that.Originally Posted by MGargano ↑Has anyone tried using the 'Blendmount' to install their Scangauge II above the rearview mirror? It looks like a pretty good idea, just not sure if it'll fit since there's not much clearance between the mirror and windshield. Their website doesn't say what vehicles it works with, so I'm curious if any Yarii owners have tried this.
http://www.blendmount.com/showthread.php?t=2
No Need i Velcro's to the roof and i won't moveOriginally Posted by MGargano ↑Has anyone tried using the 'Blendmount' to install their Scangauge II above the rearview mirror? It looks like a pretty good idea, just not sure if it'll fit since there's not much clearance between the mirror and windshield. Their website doesn't say what vehicles it works with, so I'm curious if any Yarii owners have tried this.
http://www.blendmount.com/showthread.php?t=2
1 attachment not included in this copy
LOL! Nice! Where were you before I wasted $45 on the Blendmount?Originally Posted by 1NZYaris1 ↑No Need i Velcro's to the roof and i won't move
Anyone have a problem with the Scangauge saying 'Connecting...' then turning off after about a minute without giving any data? I tried all the troubleshooting FAQs in the manual, but none seem to get it working. Weird thing is, it was working fine for a week or so, until today.