Yarisworld Archive

HID

225 posts · 66,253 views · page 3 of 5

Replies continued

Yaris-TJTijuana, Mexico · Nov 6, 2006#101
can some one post pics of ballast placements?

Did you guys have them drilled to the chasis? or

Are they tied with the straps to some of the wires?🤷 🤷
JfoofooNew Jersey · Nov 6, 2006#103
Originally Posted by Violin
Violin, Did you have to remove the front bumper to install the hi/low HID kit?
how long did it take for you to install?
I think you had the PIAA bulbs before? Is there a HUGE/BIG/Slight difference?

Thanks
Yaris-TJTijuana, Mexico · Nov 6, 2006#104
Thanks Violin! nice install!
ViolinNew Jersey · Nov 6, 2006#105
Mine aren't in yet - that's Chris's.
IsLNdbOiLas Vegas, NV · Nov 6, 2006#106
There's supposedly a small area under each headlight on the Yaris just for the ballasts, but I'm not sure if it's on the sedan or liftback.
ecoAtlanta · Nov 7, 2006#107
How many amps are the two fuses that are used for the HID's.
Yaris-TJTijuana, Mexico · Nov 10, 2006#108
🤷 Got a dumb question😕

I got my HID, it has high halogen..KLIGHT..( I know it's chinesse..but I'll give it a shot..it's not the first, and won't be the last!😁 )

the wires for the high are both yellow..I can't distinguish positive or Negative..

Do they have polarity or can I plug them indistinctively?
Yaris-TJTijuana, Mexico · Nov 10, 2006#109
FYI..KLIGHT
Picture not included in this copy

1 attachment not included in this copy

JfoofooNew Jersey · Nov 11, 2006#110
Originally Posted by IsLNdbOi
There's supposedly a small area under each headlight on the Yaris just for the ballasts, but I'm not sure if it's on the sedan or liftback.
Can anyone with LB confirm or deny this?
ViolinNew Jersey · Nov 11, 2006#111
On my liftback with cold weather package, the washer tank is so large, there is no space between the headlight and the tank - so no.
ViolinNew Jersey · Nov 11, 2006#112
OK - here we go. Here are some photos from my install of the EaglEye high/low kit.


First of all, the Yaris has a switching ground system - one the three terminals are always powered, even with the lights off and the high and low beams are controlled by switching on the ground at one of the other two terminals. This is not the more common switching positives system found on most cars. Fortunately this kit makes it easy to handle this. On their web page, this is referred to as the 'special type':
http://www.namyung.co.kr/english/hotproduct/hidh4.asp



You simply disconnect the blue and black wires and reverse them. There is a diode with a little arrow drawn on it. You pull it out and turn it 180 degrees.

Picture not included in this copy



Disconnect the battery negative before you start.

It makes it a whole lot easier if you remove the five little black pop clips on the top of the bumper and the one in each wheel well to pop the top of the bumper out.

Picture not included in this copy

Picture not included in this copy



Remove the three bolts on each headlight.

Picture not included in this copy



It’s a good idea to mask each one so they don't get scratched.

Picture not included in this copy



Disconnect the wiring harness from each light and remove the rubber boot. Wearing latex gloves, remove the old light bulbs and install the new ones. Carefully cut off the rubber boots supplied with the kit, they won't fit our headlights. Pull the wires through the factory boot and put it back in place.

Picture not included in this copy



This seemed like a good place to ground the new wiring harnesses.

Picture not included in this copy



The power wires on the new harnesses go to the positive terminal on the battery. I removed the fuses first.

Picture not included in this copy



I got some M6 - 1.00 x 10 hex screws and lock washers to attach the relays on the top of the struts.

Picture not included in this copy

Picture not included in this copy

Picture not included in this copy



These spots worked for the ballasts.

Picture not included in this copy

Picture not included in this copy



I put a cable tie around each boot.

Picture not included in this copy



...and followed it up with some self sealing rubber tape - the kind electricians use on electrical services. This stuff is expensive, but I had some already and I really wanted to keep dust and moisture out of the headlight housing. You might safely omit this.

Picture not included in this copy



Finally, reinstall the 20 amp fuses in the new harnesses, reattach the battery ground, unmask the headlights and reattach them and the bumper.

Go grab a beer and wait till dark to aim the lights.
Chris07LBNew Jersey · Nov 11, 2006#113
Originally Posted by Violin
OK - here we go. Here are some photos from my install of the EaglEye high/low kit.
Nice work! 👏 Glad to see you got everything going correctly, your post will be a BIG headache saver for anyone doing the Eagleye High/Low kits. 🙇
Be sure to make a new post once you have them installed. 👍

On a side note, the Eagleye single (low beam only) kits are cake to install, but thats because its just that,... a SINGLE beam kit! No relays to mount and wire, no need to remove headlights, just remove old, install new, and mount the ballasts.

Here's another option for mounting the ballasts, without having to drill anything.

4 attachments not included in this copy

Yaris-TJTijuana, Mexico · Nov 11, 2006#114
hi guys! gotta question! it looks like if you have dual...do you need a relay?

also..wheres the diode that has to be reversed??
ViolinNew Jersey · Nov 11, 2006#115
You only need a relay if you have another wiring harness which is really a good idea because the current draw when you first turn on your ballasts will fry your wires over time. My ballasts get powered directly from the battery - the factory wiring only serves to tell the relays on the new harness when the lights are on/off or high/low. The diode is on the new harness - if your kit doesn't have another harness, you won't have a diode.

I'm a little disappointed in the cutoff on the lighting. There is some reflection off the little doohickeys that control the high beams but overall, not bad. What isn't so good is I have to be really careful switching from high to low beams - if it bumps through the low beam position to the flash to pass position; one or both lights go off! Also, the high beam indicator doesn't work because there is no feedback from the bulb. I can live with both, I just have to be very careful when switching from high to low.



Low beam:

Picture not included in this copy



High beam:

Picture not included in this copy


Low beam on road:

Picture not included in this copy



Color (5,000k):

Picture not included in this copy
ecoAtlanta · Nov 12, 2006#116
Ok,let me get this straight before I order,with the single beam seat the boots supplied will fit right.
ecoAtlanta · Nov 12, 2006#117
And Violin,couldnt you skipe the mounting of the relays,by using a zip tie,and tie it to a wire from the engine.
Chris07LBNew Jersey · Nov 12, 2006#118
Originally Posted by eco
Ok,let me get this straight before I order,with the single beam seat the boots supplied will fit right.
Whats included in BOTH kits is a rubber gromet... the gromet (size of a quater) is simply cut off, as its used only if you were to drill a hole in the housing (not needed) to route the wires, while making a weather tight seal..
ViolinNew Jersey · Nov 12, 2006#119
But if I understand correctly, the factory boot seals the low beam only bulb like the standard H4 bulb.

I'm wondering if a resistor across the high beam ground and power on the factory plug will return functionality of the high beam indicator. I'll probably write the manufacturer regarding my two issues.
ViolinNew Jersey · Nov 12, 2006#120
Originally Posted by eco
And Violin,couldnt you skipe the mounting of the relays,by using a zip tie,and tie it to a wire from the engine.
True, but it looks much better the way I did it. There's certainly some flexibility in installation. Feel free to get creative.
ViolinNew Jersey · Nov 12, 2006#121
Oh yeah... the DRL's need to be disabled even with this kit... Sorry Canadians.
Yaris-TJTijuana, Mexico · Nov 13, 2006#122
Originally Posted by Violin
True, but it looks much better the way I did it. There's certainly some flexibility in installation. Feel free to get creative.
Correct.I had to take mine to a shop...

The guys didn't have a clue at first.

Then he figured out that the way the light worked was that it changed grounds when doing the light change..

Then he made some inverts in cables, and it worked..

Not very satisified with ligh though...

I'll try to post pictures later on..

Low HID, looks like HIGH, since it shots the light above the space where regular low was..😕 😕

High Halogen shots the light where the old LOW was..🤷 🤷

Is there a chance that when I placed the bulbs they were reversed? I now that bulbs have some kind of 3-rivets, that make it fit only in one direcction..

any ideas?🤷
Chris07LBNew Jersey · Nov 13, 2006#123
H4 bulb base, either halogen or HID, will only fit one way.

With an EAGLEYE high/low HID setup, it will be the same light brightness for the high beams, but re-directed upwards. The stock factory H4 high/low halogen bulb, will be a brighter high beam light and directed upwards.

Correct me if I'm wrong, but doesnt your setup use a halogen for the highs?

2 attachments not included in this copy

Yaris-TJTijuana, Mexico · Nov 13, 2006#124
Originally Posted by Chris07LB
H4 bulb base, either halogen or HID, will only fit one way.

With an EAGLEYE high/low HID setup, it will be the same light brightness for the high beams, but re-directed upwards. An H4 high/low halogen, will be a brighter light and directed upwards.

Correct me if I'm wrong, but doesnt your setup use a halogen for the highs?
Yes Chris07LB...it has high-Halogen / Low HID..

mine is not as you mentioned..
Originally Posted by Chris07LB
With an EAGLEYE high/low HID setup, it will be the same light brightness for the high beams, but re-directed upwards.
It's actually opposite..


I don't have the EAGLEYET, but it should work similar.. 🤷 🤷
Chris07LBNew Jersey · Nov 13, 2006#125
Originally Posted by Yaris-TJ

It's actually opposite..


I don't have the EAGLEYET, but it should work similar.. 🤷 🤷
Uh, of course it should. When you put your high beams on, no matter what kit you are currently using, it should project the light UP (high)....

Let me ask you this... when looking into your headlight housing at the bulb(s), where is the halogen, above or below the HID?
Yaris-TJTijuana, Mexico · Nov 13, 2006#126
Originally Posted by Chris07LB
Uh, of course it should. When you put your high beams on, no matter what kit you are currently using, it should project the light UP (high)....

Let me ask you this... when looking into your headlight housing at the bulb(s), where is the halogen, above or below the HID?
I took a look a this, today morning..it's actually neither way😳 😳
The halogen is pointing inwards, towards the radiator..on both sides.
And the HID are facing outwards , towards the sidewalks.. that's why at first I tough I had fit them incorrectly🤷
Chris07LBNew Jersey · Nov 13, 2006#127
Now that def sounds odd.

Take a look at my pictures posted above.. the halogen/HID one.

On a H4 housing, the bottom will be FLAT, to accept the FLAT section of the bulb when installed. To keep it lined up, while securing it into the housing, there will also be tiny little metal tabs.

Try removing one bulb, and snap a pic of its base for me.
ViolinNew Jersey · Nov 13, 2006#128
Can you tell which bulb is lit when you turn the high beams on? I guess it's possible that your installer wired it wrong.
ViolinNew Jersey · Nov 13, 2006#129
Looking at the car side of the connector you have three slots.

The vertical one on the right is always positive, the horizontal one in the middle-top is your low beam ground and the vertical one on the left is your high beam ground.
Yaris-TJTijuana, Mexico · Nov 13, 2006#130
Originally Posted by Violin
Can you tell which bulb is lit when you turn the high beams on? I guess it's possible that your installer wired it wrong.
When High Beams are turned on, Halogen are turned on, but the light aim as if it were low, but even much dimmer than stock low.😢

BTW..thanks for the support guys..
Yaris-TJTijuana, Mexico · Nov 13, 2006#131
Originally Posted by Chris07LB
Now that def sounds odd.

Take a look at my pictures posted above.. the halogen/HID one.

On a H4 housing, the bottom will be FLAT, to accept the FLAT section of the bulb when installed. To keep it lined up, while securing it into the housing, there will also be tiny little metal tabs.

Try removing one bulb, and snap a pic of its base for me.
I'll get the picture tonight, once I get gome...Also will take some of the balast placement I got..

Also, what would be the proper fitment, HID on top, and Halogen at bottom?

If this is the case, then mine are odd...
Chris07LBNew Jersey · Nov 13, 2006#132
Originally Posted by Yaris-TJ

Also, what would be the proper fitment, HID on top, and Halogen at bottom?
Re-read what I wrote.. the bulbs will only fit one way, if its indeed the correct H4 fittment.

But yes, the high beam halogen should be on the top, IF its like the halogen/HID picture I posted above.

Where's the seller, and all his support?
GabLToronto · Nov 13, 2006#133
Anyone heard of Enon brand? Is it any good?
Yaris-TJTijuana, Mexico · Nov 15, 2006#134
Picture not included in this copy

Here's a pic of my problematic HID..

one metal tab fits up, and the other 2 fit down. by doing this, high halogen is on right hand side..

is this correct?🤷 😕

1 attachment not included in this copy

Chris07LBNew Jersey · Nov 15, 2006#135
Again, that does look and seem very odd.

Out of all the high/low HID kits I have seen, where a halogen is used for the high beam, it was always the top bulb.

Have you contacted the seller for support???

Also, the base for an H4 should look like this.......

1 attachment not included in this copy

Chris07LBNew Jersey · Nov 15, 2006#136
After looking at your picture a little more, maybe they were not assy. correctly.

Is there a way to shift/turn the WHITE center, in the BLACK base, so that the halogen is on top, and the HID is at the bottom?
Yaris-TJTijuana, Mexico · Nov 15, 2006#137
Originally Posted by Chris07LB
After looking at your picture a little more, maybe they were not assy. correctly.

Is there a way to shift/turn the WHITE center, in the BLACK base, so that the halogen is on top, and the HID is at the bottom?
thanks for the feedback Chris, i've definitely contacted the seller today with this missplacement issue, i'll see his feedback.

I'll also check if I can disassemble the base and try to rotate it, to the correct alignment,

Thanks for your support👏
ViolinNew Jersey · Nov 16, 2006#138
Whatever you do, don't get oil from your skin on the bulb! Wear latex gloves.
Yaris-TJTijuana, Mexico · Nov 16, 2006#139
Originally Posted by Violin
Whatever you do, don't get oil from your skin on the bulb! Wear latex gloves.
thanks for the warning Violin..one finall question...I hope this will make it...

I can get rid of the high beam, since it has a bolt that I can unscrew..

my question is, what is the correct position for the small rod on the hid? is it pointing down?

I 'll use this as a baseline, and get rid of the high..😠 😠 ..😢 😢
the_saintOmaha, somewhere in middle america · Nov 16, 2006#140
If you do happen to get the bulb dirty/oily/whatever. You can use denatured alcohol to clean it. I picked up a tin of it at home depot....I want to say it was $4. It's good insurance to have when dealing with hundred dollar lightbulbs.
Chris07LBNew Jersey · Nov 16, 2006#141
Originally Posted by Yaris-TJ
thanks for the warning Violin..one finall question...I hope this will make it...

I can get rid of the high beam, since it has a bolt that I can unscrew..

my question is, what is the correct position for the small rod on the hid? is it pointing down?

I 'll use this as a baseline, and get rid of the high..😠 😠 ..😢 😢
If your going to go through that much trouble to now only have a low beam kit, for the price of a high/low, SEND THEM BACK!

I would not touch a thing, until after you hear from the seller. 🙁
ViolinNew Jersey · Dec 22, 2006#142
I was planning on just putting the low beam only in the stock reflector and mounting it so I can use the factory adjusters like so:

Picture not included in this copy

My high beams would be mounted in the fog light position.


However, there is a ton of space in there. I just might put the low beam HID along with the Hella 90mm halogen high beam unit

Picture not included in this copy

sorta like this:

Picture not included in this copy

I could make aluminum shrouds and use a black ABS sheet to dress up the inside of the housing.

Decisions, decisions....
Chris07LBNew Jersey · Dec 22, 2006#143
My god Rob, that's going to be KILLER!! 🤤

Good thing your close by, it will save me the shipping charges when you do mine! 😁
ViolinNew Jersey · Dec 22, 2006#144
If I go the route without the stock reflector, I think my paint guy has enough leftover meteorite metallic paint to do the inside of the housings. That would go well with my Modellista tails.

Maybe I can squeeze those Bosch mini projectors inside the stock reflector and use them as my high beam...
07yaris_feThread starterCanada · Dec 22, 2006#145
Thanks for all the replies..... finially solve my problem
is the wire problem, now fixed.....
paultyler_82USA · Dec 23, 2006#146
Originally Posted by Violin ↑
If I go the route without the stock reflector, I think my paint guy has enough leftover meteorite metallic paint to do the inside of the housings. That would go well with my Modellista tails.

Maybe I can squeeze those Bosch mini projectors inside the stock reflector and use them as my high beam...
Bro, I think with the proper housing, that is going to look absolutely killer!
ChinoCharlesOH · Dec 23, 2006#147
Dude, do I see projectors? 🤤
eTiMaGoBangkok, Thailand · Dec 23, 2006#148
The Toyota Wish has a similar shape of headlamp, you could get some inspiration from it:

Picture not included in this copy
ViolinNew Jersey · Jan 8, 2007#149
I decided to go with a single Bosch E46 projector in the stock reflector bowl with the A4 bezel. Highs are halogens in the foglight position.

I was working on the rotational aiming tonight. I still have some work to do but here's a teaser:

3 attachments not included in this copy

Chris07LBNew Jersey · Jan 9, 2007#150
Lets see some cut off pics. Looks awesome so far! 🤘