Yarisworld Archive

sealed the hood.

57 posts · 13,196 views · page 1 of 2

kouOriginal postnj · Oct 27, 2008#1
i did not like the gap beween the hood and front bumper,paraniod about rain getting on the filter so i sealed it up with what it should have came with.this strip if from nissan i had to drill some holes in the bumper for the tabs to snap in.overall i think it looks a lot cleaner now without the void.

2 attachments not included in this copy

Replies 56

Nexus1155Dorchester · Oct 27, 2008#2
looks very clean and professional good job!
ROCKLAND TOYOTAROCKLAND COUNTY NY · Oct 27, 2008#3
i just looked at the camry ones we have and it just might work. its a little bit wider than yours but it can be trimmed. part number is 53395-06010..........
cali yarisCanoga Park, CA · Oct 27, 2008#4
EXCELLENT, looks great, very clever! 👏
Thej3sta2Orlando, FL · Oct 27, 2008#5
Great job man should post part #s and A DIY
drbilalNYC | Pakistan · Oct 27, 2008#6
Nicely done.
kouThread starternj · Oct 27, 2008#7
thanks everyone. i will have to look for the part # i had this thing sitting around for a while.
PHXDEMONPhoenix, AZ · Oct 27, 2008#8
Looks great 🤘 In for a DIY.
ZINGLebanon, Middle East. · Oct 27, 2008#9
Excellent work there. Now you got me paranoid about mine leaking haha, so +1 for the DIY comment.
bobselectricwest harrison, ny · Oct 27, 2008#10
Nice job Kou! Looks a lot better than the half way full strip that we were looking at at the show
custom LftbackHouston, TX · Oct 27, 2008#11
Awesome job, looks great! 🤘
tk-421Dagobah · Oct 27, 2008#12
Good job!
+1 for the DIY idea
IsLNdbOiLas Vegas, NV · Oct 27, 2008#13
Nice. Now we need a part number for a strip that's the right length / size for our hoods and then a DIY!
TEHxFALLEN V1.2Calabasas, CA · Oct 28, 2008#14
Very clever! Lookin' good! 👍
battleversiontc808 · Oct 28, 2008#15
thats actually a good idea
StolnWinnipeg, Canada · Oct 28, 2008#16
Do you remember what Nissan it came from so we can look for a part number as well?
Smokey159Lexington, KY · Oct 28, 2008#17
Yeah, partnumber of the one you used would be great! Great Idea, but what about the gap by the headlights?
Klink10910 · Oct 28, 2008#18
Just came in from looking at mine....for those wanting to do this try the rubber seal used on the cowling to seal the hood. Pulled mine and dry fitted. Plastic pins already there and when centered and with a few drilled holes....bingo. Don't imagine that trim piece would be to much and saves time. Just head to the dealer.
cleongSingapore · Oct 28, 2008#19
It'll probably look better on a dark coloured car than one of the lighter-coloured cars. The rubber strip would probably be quite obvious in the gap between the bumper and bonnet.
AothachosLong Island, NY · Oct 28, 2008#20
i would so do this deffinatly
ShroomsterOrlando · Oct 28, 2008#21
Originally Posted by ROCKLAND TOYOTA ↑
i just looked at the camry ones we have and it just might work. its a little bit wider than yours but it can be trimmed. part number is 53395-06010..........
this looks to be a possibility for a toyota part....
kouThread starternj · Oct 28, 2008#22
i cant find part# sorry. jc whitney sells alot of weather seals this would be a good place to look.
wsladaritzBenton, AR · Oct 28, 2008#23
Hey Rockland, u mentioned the camry part could prolly be trimmed. Is that rubber flexible enough to bend to the shape of the Yaris hood where it would put? Did I DIY thread get started for this yet? How much and where to get that camry part so we can do this also if we don't have access to an old nissan layin around... 😆
kouThread starternj · Oct 28, 2008#24
the idea started with the new camry. they have the hood seal which rockland is taking about.
StolnWinnipeg, Canada · Oct 28, 2008#25
I did a search for the rubbeer seal for the cowl to hood and the following is the part number: 53383B SEAL, HOOD TO COWL TOP
53383-52050 NCP91 1 $16.28. Is this the part you are referring to, Klink10? I found the info at www.toyodiy.com My car is a 2007 5 door Canadian RS so the part number may vary but check this site out and enter your car info.
kouThread starternj · Oct 28, 2008#26
that seal is not as sturdy. you will need more clips to hold it in position.
ChinoCharlesOH · Oct 28, 2008#27
Nice. Keep this thread rolling... more info! More info!
StolnWinnipeg, Canada · Oct 28, 2008#28
Kou,

What Nissan did you borrow the seal from. Hopefully you remember this since the part number is not on the tip of your tongue.
slothman86Savannah, GA · Oct 28, 2008#29
i was just thinking about doing that!
kouThread starternj · Oct 28, 2008#30
i found 2 #'s i am going to check at nissan which it is so that i can see the image to make sure its the right one. get the info up later.
StolnWinnipeg, Canada · Oct 28, 2008#31
Awesome, thanks for getting this info for us, maybe you could do a DIY of the one you did so we can see where you drilled and how you managed to bend it to match the curves of the car
Thej3sta2Orlando, FL · Oct 28, 2008#32
that would be tight son
eiiLong Beach, CA · Oct 28, 2008#33
Originally Posted by Stoln ↑
Awesome, thanks for getting this info for us, maybe you could do a DIY of the one you did so we can see where you drilled and how you managed to bend it to match the curves of the car
+1. Cool clean mod kou. looks like stock, should be stock.
kouThread starternj · Oct 28, 2008#34
DIY in diy section.
IsLNdbOiLas Vegas, NV · Oct 28, 2008#35
Too bad they don't make white rubber strips like this...
kouThread starternj · Oct 28, 2008#36
i dont think it would look as bad as the gap.
marcustoronto, canada · Oct 30, 2008#37
this is wicked... so was that the right part #
IsLNdbOiLas Vegas, NV · Dec 9, 2008#38
Here's an alternative way of doing this:
http://www.soffseal.com/SearchByPart.asp

Part #: E006A

I ordered 4ft. of the stuff, but ended up having to shorten it.


This weatherstrip comes pre-attached with 3M weather-proof double sided tape:
Picture not included in this copyPicture not included in this copy
Picture not included in this copy
RagnaCaTVillalba, Puerto Rico · Dec 9, 2008#39
Originally Posted by IsLNdbOi ↑
Here's an alternative way of doing this:
http://www.soffseal.com/SearchByPart.asp

Part #: E006A

I ordered 4ft. of the stuff, but ended up having to shorten it.


This weatherstrip comes pre-attached with 3M weather-proof double sided tape:
Nice got a pick closed?
jinxorSydney, Australia · Dec 9, 2008#40
nice.....
may i ask what is the length you measured....
IsLNdbOiLas Vegas, NV · Dec 9, 2008#41
Can't really see it from the outside / when the hood is closed since I have the hood deflector on there now. These are the best pics. I could take of it while the hood is closed:
Picture not included in this copy
Picture not included in this copy



It makes a nice, tight seal for the front of the hood. Before, I could just lift the hood and drop it to close it. Now, I have to actually push the hood closed.

I purchased 4ft. of this weatherstrip. Didn't measure the final length after cutting because most of it was already stuck on and I didn't want to remove it to straighten it out and take a measurement.
jinxorSydney, Australia · Dec 9, 2008#42
ok... thanks
RagnaCaTVillalba, Puerto Rico · Dec 10, 2008#43
Hmmmm? How about sticking it to the Hood? I think most cars have it on the Hood.
YarisSedanCalifornia - Bay Area · Dec 10, 2008#44
I ordred the same thing from softseal. Only 6 bucks shipped. Cant beat that. cant wait to install. Maybe will cut down on wind drag and improve my gas milage by .5 percent.
derickveliz2Central, MA · Dec 10, 2008#45
Originally Posted by YarisSedan ↑
I ordred the same thing from softseal. Only 6 bucks shipped. Cant beat that. cant wait to install. Maybe will cut down on wind drag and improve my gas milage by .5 percent.
It's $3.70 / FT
How much did you buy? tell me if I'm wrong.
IllusionXBrossard, QC · Dec 10, 2008#46
Originally Posted by RagnaCaT ↑
Hmmmm? How about sticking it to the Hood? I think most cars have it on the Hood.
sticking it on the hood is probably safer for the paint. Plastic don't rust, whereas the hood would rust if the paint is gone...
IsLNdbOiLas Vegas, NV · Dec 11, 2008#47
I don't understand why it would be better to stick the weatherstrip in the underside of the hood...
spookzSydney, Australia · Dec 11, 2008#48
Most cars which have this seal from factory have it clipped into the underside of the hood. Also, I don't think the factory paint would rub off that easily. If it does then you've got serious issues, and should take the car back to the dealer.
bobselectricwest harrison, ny · Dec 11, 2008#49
UH-OH--- sounds like a VPCORP answer😉
spookzSydney, Australia · Dec 11, 2008#50
LOL, what's that mean?