Yarisworld Archive

DIY Cabin Air Filter

101 posts · 146,612 views · page 1 of 3

BailOutOriginal postReno, Nevada, USA · Sep 13, 2007#1
This method will create 8 cabin air filters of the appropriate size (8.5x7.25x1") which should cover your filtration needs for 2 years. Assuming you have the the tools on hand the only additional cost is a filter that sells at any home improvement store for between $4 and $15 depending on your desired level of filtration. I prefer an allergen rated one that goes for $15 but even a cheap one is better than none at all.

Supplies needed: 20x30x1" central air style filter for a home, tin snips, duct tape, marking implement, measuring implement

Time: 30 minutes

Directions:

1) Lay the filter on a flat, clean surface and mark two lines along the length of it 8.5" from either side. This will leave an "alley" of 3" in the middle which is excess.

2) Starting at one edge of the filter follow the line you just created and mark it at 7.25" and 14.5". Now come in from the opposite edge and do the same. You should be able to make 4 of these 8.5x7.25" rectangles on each side for a total of 8, with 1" of excess remaining in the middle.

3) Use tin snips or an equivalent to cut out the 8 rectangles, ensuring you cut through all metal and all paper layers. If a little paper flakes off don't worry about it. Draw arrows to mark the air flow direction on the paperboard edge of each rectangle.

4) Use duct tape to enclose the side edges of each rectangle that are free, ensuring that you cover the top, side and bottom edges as you go. Try to not compress the filter material too much when you do this.

5) Store all but one of your new filters in a paper or plastic bag to keep them clean for later usage.

6) Remove the passenger side's lower glove box by pressing in on the right side and popping it out, then repeating the same for the left side.

7) Remove the filter tray's cover by pinching the 2 small parts on the right and pulling backward on the piece (this requires almost no strength so if it's fighting you you're doing it wrong), then pulling it away from the left side.

8) The filter fits in lengthwise. Match the airflow direction of the system, keeping in mind that air flows downwards as it is inducted by the fan right below the filter area. If you forgot to mark the air flow direction it's not the end of the world as most modern filters work in both directions. Insert the filter's rear-left corner first, then push back and sweep it to the left until both sides of the filter are in. It will be a tight fit and will likely cause a bit of flexing/compression on the filter. This is normal but try to keep it to a minimum.

9) Push the filter away from you until it is flush against the rear of the tray area. It will look like it's sticking out a bit but remember there is some clearance behind the cover you removed.

10) Replace the tray cover, left side first, ensuring that the right side snaps into place properly. Give the cover a light tug once it's reinstalled just to be sure it's not loose.

11) Replace the glove box.


You're done!
supplies.jpgfinished_filter.jpgremoving_glovebox.jpgremoving_glovebox2.jpgtray_closed.jpgtray_cover_removal.jpgtray_cover_removal2.jpginstalling_filter.jpginstalling_filter2.jpginstalled_filter.jpg

Replies 100

YamilRSan Diego, CA · Sep 13, 2007#2
very good DIY
YarisTom73Johnstown, PA · Sep 13, 2007#3
Nice DIY, you get half a dozen filters for the same $15 I paid for one Autozone Bosch. And, I think it filters even better than mine! Only one concern: are the airflow characteristics of our little fans anywhere near what you'd find in an average home furnace setup? In other words, would this filter stifle our car's ability to flow A/C or heat?
kimonaHuntington Bch, CA · Sep 13, 2007#4
Nice post!
BailOutThread starterReno, Nevada, USA · Sep 13, 2007#5
Originally Posted by YarisTom73 ↑
Only one concern: are the airflow characteristics of our little fans anywhere near what you'd find in an average home furnace setup? In other words, would this filter stifle our car's ability to flow A/C or heat?
I don't have specific numbers for our car's ventilation blower but the drop in air flow once I installed one of my filters was quite low. This means while there is some load on the system it's not much at all.

Any filtration is going to impede the flow a bit.
YarisTom73Johnstown, PA · Sep 13, 2007#6
Agreed..I think perhaps your idea may actually flow better than the Bosch one! Next change, I'm trying your way. 👍
KSIbuckyFond du Lac, WI · Sep 13, 2007#7
hey you know what also really works (if you have a warranty) go in and say that your a/c doesnt work

i did (i got a new compressor) but they also got me a new filter
OgDoggPhoenix, AZ · Sep 15, 2007#8
If only I'd seen this before paying $25 for one at the dealership...
kimonaHuntington Bch, CA · Sep 15, 2007#9
Originally Posted by OgDogg ↑
If only I'd seen this before paying $25 for one at the dealership...
That's why it pays to do a search of the forum.

This information, plus reference to the Purolator and Bosch A/C cabin filters (about $10 each), can be found in numerous threads!
Super_BQNew Zealand · Oct 19, 2008#10
Just to let others know that i've done this same DIY filter job for NZ/Aus/UK Yaris models. It appears the same spot behind the glove box however, the whole fan system is slightly positioned to the right side of the glove box making it not as easy to fit the filter in. I often wonder how even a hard factory fitted filter would even fit into the opening as the opening of the glove box isn't wide enough? Or do the factory cabin filters are the flexible kind?

BQ
edisonfireToronto, Ontario, Canada · Mar 30, 2009#11
which way should the air flow circulation go?
SilverBackEl Monte, Ca · Mar 30, 2009#12
Nice DIY! One more reason to tell the dealer to shove it...

Originally Posted by edisonfire ↑
which way should the air flow circulation go?
Air flows upward through the filter before reaching the vent openings
edisonfireToronto, Ontario, Canada · Mar 30, 2009#13
thanks dude
blacksandiegovitzJust chillin' out brah ! · Mar 30, 2009#14
Cool post / good DIY . I was just about to do something about the cabin air filter , as I'm sick of that smell of "funk" lol
mikenacaratoBrentwood, TN · Mar 30, 2009#15
i have a fram fresh breeze in there :)
blacksandiegovitzJust chillin' out brah ! · Mar 30, 2009#16
Originally Posted by mikenacarato ↑
i have a fram fresh breeze in there :)
was that just a basic size cabin filter or is it made/listed to fit the yaris ???
mikenacaratoBrentwood, TN · Mar 30, 2009#17
i took my oem filter into walmart and found one that was close. i had to trim it down length wise by a half inch and it fit like a glove.
1stToyotaOklahoma · Apr 3, 2009#18
Originally Posted by edisonfire ↑
which way should the air flow circulation go?
Actually, flow is downwards. Just changed out my OEM filter and it was dirty on the top. Blower motor sits underneath filter and draws the airflow downwards to distribute air thru the system. Only thing above the filter is the fresh air intake.

So, if you get the OEM filter the arrow goes up because it says "UP", not flow. On my Beck/Arnley filter, arrow points down because it's talking about actual air "flow".
LafiroNYC · Apr 17, 2009#19
I own the 2007 sedan, and I don't think the cabon air filter comes with the car.

If I follow this DIY will the location of the air filter be in the same place?
Thanks.
BLHCT · Apr 17, 2009#20
My 2007 users manual said if it was installed. A sticker would be attached to the inside of the Glove Compartment Door.

Mine had no sticker.

I believe the compartment is there to accept it. It was just not installed at the factory. Will know tomorrow when I try to install the one I have on order.
Local parts store was out of it.
YarisSedanCalifornia - Bay Area · Apr 17, 2009#21
I think this mod would hinder the air flow slightly. If you ever look at a oem cabin air filter it has arrows that has to be installed a certain way. The way its designed to allow maximum air flow. If you take a filter thats not designed to be a cabin air filter it wont have the same type of flow rate.
BailOutThread starterReno, Nevada, USA · Apr 17, 2009#22
Originally Posted by YarisSedan ↑
I think this mod would hinder the air flow slightly. If you ever look at a oem cabin air filter it has arrows that has to be installed a certain way. The way its designed to allow maximum air flow. If you take a filter thats not designed to be a cabin air filter it wont have the same type of flow rate.
Any filtration hinders flow to a certain degree, but your assumptions rely wholly on the assumption that a home blower filter restricts more than a car blower filter designed by some 3rd party to absolutely no one's specifications but their own. Your assumptions also assume that the direction of flow really matters, which it often does not (arrows are often put on there just to keep folks from asking questions, and the one that I used in the photographs is identical top and bottom).

The experience of myself and others that have done this DIY shows that it works just fine. I've been using my own filters for a year and a half now.
1stToyotaOklahoma · Apr 18, 2009#23
Originally Posted by BailOut ↑
Any filtration hinders flow to a certain degree, but your assumptions rely wholly on the assumption that a home blower filter restricts more than a car blower filter designed by some 3rd party to absolutely no one's specifications but their own. Your assumptions also assume that the direction of flow really matters, which it often does not (arrows are often put on there just to keep folks from asking questions, and the one that I used in the photographs is identical top and bottom).

The experience of myself and others that have done this DIY shows that it works just fine. I've been using my own filters for a year and a half now.
Maybe the assumption is based upon store bought cabin filters being 100% filter (surface area) and DIY filters are bordered with cardboard and tape that migrates upon the filter surface area? Air won't flow through cardboard and tape.
BailOutThread starterReno, Nevada, USA · Apr 18, 2009#24
^ ^ Good point. However, as has been said, there have been no complaints in 18 months. It just works. 🙂
talnlnkySpokane, Wa · Apr 18, 2009#25
Originally Posted by YarisSedan ↑
I think this mod would hinder the air flow slightly. If you ever look at a oem cabin air filter it has arrows that has to be installed a certain way. The way its designed to allow maximum air flow. If you take a filter thats not designed to be a cabin air filter it wont have the same type of flow rate.
yeah.... who cares.... humans can't tell the difference... i've got one year of experience with this type of DIY filter.

Also... this would ONLY be a problem if you drive around with your air on MAX all the time and still felt you needed a stronger fan in your car.


All who drive around town with the fan on max all the time please raise your hand.
...


thought so.
ozmddDFW, TX · Apr 18, 2009#26
Home air filters are also labeled for direction of flow. The AF rate should not be hindered to any meaningful degree. Probably less resistance than an OEM filter.
1stToyotaOklahoma · Apr 18, 2009#27
I don't know this system, but flow problems with cabin air filters can sure ruin a blower motor resistor that isn't able to cool itself properly.
YarisSedanCalifornia - Bay Area · Apr 18, 2009#28
The filter that you are using are designed for a very high powered fan that cools your entire house. Not a ity bitty fan that sucks just a little air. If you look at the blow motor it is really a tiny fan. I am all about DIY but i belive there is a noticible difference. I think no one really has noticed because the people doing this DIY dont have a filter to begin with so there is nothing really to compare to. Plus as stated before there is less surface area for the air to go through. You are putting a restriction against the blower motor when you are doing this. I dont honestly think there is a world of a difference and it wont cause catastofic failure of your blower motor circuit. But just stating there is a difference.

The cabin air filter is designed for maximum filtration without sacrificing air flow. If you get a really good quality cabin air filter they can last about 25k miles. I mean really is it worth all the time and hassle to go to the store buy the filters cut them up and then duct tape them together and have to replace them more frequently to save over the course of a 100k miles and if you dont drive that much its maybe 10 years the most a hundred dollars.

Because of the different type of filter they are going to become more restrictive when they are dirty than the cabin air filter will get when they are dirty.
talnlnkySpokane, Wa · Apr 18, 2009#29
i'd rather have cleaner air than more air.... the DIY way means you have the chance for better quality filter media. 3M Filtrete right here.
jpaduaPhilippines · Apr 20, 2009#30
Hey guys, I also made a DIY filter from simple materials, might be cheaper. You can also replace the filter element. The one I made is a bit crude but it works hehehe 👍, but I'm planning to build another one but this time instead of cardboard I'll use plexiglass, but this will do for now.

Materials:
Aircon filter and nylon screen which you can purchase at any home/hardware store
Picture lost · www.jaypadua.com
Small cardboard giftbox which is roughly about 7" x 9" x 1"

How I built the aircon filter holder:

1. Cut out 1" from the long side of the box.
2. Re-enforce the box flaps with elmers glue
3. Cut out a hole about 1" from the sides in the middle of the box and the lid
4. Cut enough nylon screen to cover the hole on both the box and the lid
5. Staple the nylon screen to the box and lid, then reinforce with some Masking tape
6. Reinforce the box with more masking tape
7. Cut a piece from the aircon filter just enough so that it can fit inside the box

You will have something like this:
Picture lost · www.jaypadua.com
Picture lost · www.jaypadua.com

8. Place the aircon filter on the box
Picture lost · www.jaypadua.com

9. Place the lid upside down so that you will have a screen-filter-screen sandwich.
Picture lost · www.jaypadua.com
Picture lost · www.jaypadua.com

Installation:

10. Remove the glove box.
Picture lost · www.jaypadua.com
Picture lost · www.jaypadua.com

11. Remove the aircon filter cover.
Picture lost · www.jaypadua.com
Picture lost · www.jaypadua.com

12. Insert the DIY filter lengthwise.
Picture lost · www.jaypadua.com
Picture lost · www.jaypadua.com

You will have enough filter material, for several replacements.
1stToyotaOklahoma · Apr 20, 2009#31
Originally Posted by talnlnky ↑
i'd rather have cleaner air than more air.... the DIY way means you have the chance for better quality filter media. 3M Filtrete right here.
You won't get much better than OEM or WIX for quality filtering, and if you do then you can almost assure yourself that airflow, blower motor and resistor will suffer as the result.
BailOutThread starterReno, Nevada, USA · Apr 20, 2009#32
Originally Posted by 1stToyota ↑
You won't get much better than OEM or WIX for quality filtering, and if you do then you can almost assure yourself that airflow, blower motor and resistor will suffer as the result.
Those are fairly broad statements without anything to support them. I do not recall ever seeing an OEM or Wix filter that was allergen rated but the 3M home filter I used in this DIY is. 18 months of usage without an issue shows that it doesn't hurt any part of the ventilation system.

Before the hack there were over 30 posts in this thread from folks that had done this DIY and were happy with it. I understand that some people prefer a custom made filter but that is no reason to malign a proven DIY version of it with fabrications and alarmism.
1stToyotaOklahoma · Apr 20, 2009#33
Originally Posted by BailOut ↑
Those are fairly broad statements without anything to support them. I do not recall ever seeing an OEM or Wix filter that was allergen rated but the 3M home filter I used in this DIY is. 18 months of usage without an issue shows that it doesn't hurt any part of the ventilation system.

Before the hack there were over 30 posts in this thread from folks that had done this DIY and were happy with it. I understand that some people prefer a custom made filter but that is no reason to malign a proven DIY version of it with fabrications and alarmism.
They call them pollen filters, and the WIX, Fram, OEM, and maybe another one or two have some sort of charcoal...mildew fighter...along those lines...and you know what you're getting. You don't know what you're getting if someone overdoes it with an expensive, dense home filter. I wouldn't want to be around if a vehicle was taken into the dealership with a ventilation issue and the tech finds a DIY project. I've seen enough resistors burned out to know that proper airflow is critical to their operation. They had cabin air filters that had never been replaced. Like I said before I don't know about the Yaris, but the Fords and Nissans that come to mind needed maximum flow, using a more restrictive approach wouldn't be better once the filter started getting dirty. Maybe that's why a lot replace them every 3 to 5K instead of the normal 15K reccomendation. It's not alarmism, it's just concern about people thinking they have the better than OEM answer for cabin air filters, but wouldn't dream of ever trying to show OEM how it's done when it comes to their other filters, like oil filter and engine air filter. You've just got two kinds of owners: ones that follow the rules and go by Toyota's standards for OEM parts, proper oil viscosity, tire pressure, etc...and those that will do it their way and not follow those rules whenever able.

NAPA Cabin Air Filters Are Treated w/ Enviro-Shield ! A Patented Chemical Treatment That Inhibits The Growth Of Mold, Mildew, Algae + Bacteria. The Media Traps These Harmful Microbes To Keep Your Vehicle 100% Odor + Allergan Free - EPA Approved
eTiMaGoBangkok, Thailand · Apr 20, 2009#34
as with any DIY project, it should be done at your own risk. Use a filter too dense that it fries your blower motor, too bad.. Though I'd think you might notice that the vents are barely blowing any air...
LafiroNYC · Apr 20, 2009#35
Does anyone know if the major service include a cabin air filter, or for that matter any of the major services that are done at the dealership?

I just did this DIY and found that there was NO cabin air filter.
And this made me really mad, and now I see the reason why when I slapped the seats the other day driving, the biggest clouds of dust kept coming off them like I have never seen.

I have since then installed an cabin air filter, and vacuumed my seats clean.

If the services were to include the cabin air filter, then I will be going there soon and demanding refunds or free cabin air filters.... because that was not right.
1stToyotaOklahoma · Apr 20, 2009#36
Originally Posted by Lafiro ↑
Does anyone know if the major service include a cabin air filter, or for that matter any of the major services that are done at the dealership?

I just did this DIY and found that there was NO cabin air filter.
And this made me really mad, and now I see the reason why when I slapped the seats the other day driving, the biggest clouds of dust kept coming off them like I have never seen.

I have since then installed an cabin air filter, and vacuumed my seats clean.

If the services were to include the cabin air filter, then I will be going there soon and demanding refunds or free cabin air filters.... because that was not right.
We don't get one from the factory, but I think checking/replacing the cabin filter is scheduled every 15K miles under normal conditions.

edit: I lied. That's for the engine air filter, not the a/c filter. No mention of the cabin air filter in the maintenance book that I could see. Only mention of the cabin/air conditioner filter is in the owner's manual; just says a/c filter should be replaced often to maintain proper a/c efficiency.
nemelekArizona · Apr 20, 2009#37
My dealer is real proud of their price.
Go Toyota.jpg
talnlnkySpokane, Wa · Apr 20, 2009#38
the toyota people won't even look at the air filter location unless there is a sticker in that lil glovebox/compartment area on the passenger side (by the knees under the dash). I believe the stick denotes when it was installed and when it should be replaced.

If the service person doesn't see the stick... it means there was never a filter installed by the service dept.
LafiroNYC · Apr 20, 2009#39
What is this A/C filter you are talking about?

I know where the air intake filter is in the engine bay.

I also know where the cabin air filter is behind the glove box.

But where is this A/C filter??

Also it still smells wierd at times when the A/C is used/just turning off, its wierd and people don't like it one bit.

Thanks for the help.
YarisSedanCalifornia - Bay Area · Apr 20, 2009#40
Originally Posted by Lafiro ↑
What is this A/C filter you are talking about?

I know where the air intake filter is in the engine bay.

I also know where the cabin air filter is behind the glove box.

But where is this A/C filter??

Also it still smells wierd at times when the A/C is used/just turning off, its wierd and people don't like it one bit.

Thanks for the help.
Maybe theres mold growing on your cabin air filter. How many miles you have on the car chances you never changed it
jpaduaPhilippines · Apr 20, 2009#41
Originally Posted by Lafiro ↑
What is this A/C filter you are talking about?

I know where the air intake filter is in the engine bay.

I also know where the cabin air filter is behind the glove box.

But where is this A/C filter??

Also it still smells wierd at times when the A/C is used/just turning off, its wierd and people don't like it one bit.

Thanks for the help.

I think that the cabin filter and A/C filter are the same, thats the only place I know you where you can replace the filter.
1stToyotaOklahoma · Apr 21, 2009#42
Originally Posted by Lafiro ↑
What is this A/C filter you are talking about?

I know where the air intake filter is in the engine bay.

I also know where the cabin air filter is behind the glove box.

But where is this A/C filter??

Also it still smells wierd at times when the A/C is used/just turning off, its wierd and people don't like it one bit.

Thanks for the help.
Same thing. In the owner's manual Toyota calls it the A/C filter, probably to make it seem more vital. If Fram makes one for our car you might try one of theirs. They're protected with baking soda. Or a WIX/Napa filter...they're treated to help against mold and meldew.

"NAPA Cabin Air Filters Are Treated w/ Enviro-Shield ! A Patented Chemical Treatment That Inhibits The Growth Of Mold, Mildew, Algae + Bacteria. The Media Traps These Harmful Microbes To Keep Your Vehicle 100% Odor + Allergan Free - EPA Approved"
LafiroNYC · Apr 21, 2009#43
Oh, my car NEVER had a cabin air filter until I made and installed one two days ago.

Still smells though. Im thinking of taking it out, and turning on the fan to max, and throwing bits of baking soda powder to the fan......
probably a bad idea...
Or someone suggest what I do please.
YarisSedanCalifornia - Bay Area · Apr 21, 2009#44
ive posted this a few times already but purchase febreeze antimicrobial and spray it into the air ducts as it goes through your a/c system it will kill all the bacteria and also give your ac system a fresh clean scent for a few days.
LafiroNYC · Apr 21, 2009#45
ok, will do, thank you.

My friend also has an ozone machine for the car to kill off stuff/give it that fresh car smell or something. It is really strong, makes my Sharper Image Ionic Breeze smell like nothing compared to it lol.

I will do both.
AstromanWenatchee, WA · Apr 22, 2009#46
What a great reminder I need to cut up that new filter I bought for the cars. I just took out the last one I had installed 🤮
LafiroNYC · Apr 22, 2009#47
Alright, so I did this my way first.

Sprayed the antimicrobial in the car, vents, intake while a/c and heat were on, and then seats/floors.

Then left the ionic breeze on high in the car, and sprayed it again everywhere before closing the windows as much as possible and leaving it in the car.

So I left that since 9pm last night, and wont touch the car until 5pm or so tonight.

If it aint perfect after that, I will do the ionic breeze again tonight, and then when I can drive the 26miles to my friends shop, I will use that Ozone machine.
LafiroNYC · Apr 22, 2009#48
Wow, I should not have done that second spray of antimicrobial, BUT the car smells brand new.

My friends Mercedes S600 smells the way mine does now, and I don't know how thats possible, but I love it now LOL.
RedRideMiddletown, NY · Jun 14, 2009#49
I have been making the same type of cabin filters for my Celica for years.

Now, I know how to do it (the exact dementions needed,etc) for my Yaris. 🙂
1stToyotaOklahoma · Jun 18, 2009#50
Originally Posted by mikenacarato ↑
i have a fram fresh breeze in there :)
I couldn't stand the musty wet dog smell coming out of my vents every morning any more, got real desperate 😉 and installed a FRAM FreshBreeze...smells like a little powdered baby in there now 🎉

The filter that I removed was a new Beck/Arnley...I'll save it for this winter.