Yarisworld Archive

Sway Bar Frame Bushings, Clunking Noise

6 posts · 237 views

lightdisc2Original postUS · Nov 9, 2026#1
On my 08 manual liftback with 264k miles I have had an occasional clunking noise from the front left when turning slowly over an incline, usually going into a parking lot or driveway. I have heard it happen a few times also when not turning, driving through a divot or over a bump. I drive several hundred miles per week and this has been happening for maybe 1-3k miles.

The front struts are 2.5 years old, the control arms and bushings were replaced this past spring along with the sway bar links, the cv axles are good, the bearings are good. A trustworthy mechanic checked it for a 2nd time recently and noticed the left tie rod had some play, so that was replaced. He said everything else was tight and looked fine. The noise persisted.

I am thinking it could be the sway bar frame bushings. My mechanic told me it's not worth fixing because the labor costs can get absurd. I am in the rust belt and he said dropping the subframe could get really expensive. Could this be the right tie rod even though he didn't notice an issue with it, or is it more likely the sway bar frame bushing, and could I expect another shop to be willing to do it for a reasonable price? Doing it myself is not an option. Does anyone know what price to look for to pay someone to do this? Thanks for any advice.

Replies 5

momoivanoffNJ · Nov 9, 2026#2
I was quoted $400+ for this and I did it myself. The subframe doesn't need to be dropped but lowered a little to get access.
lightdisc2Thread starterUS · Nov 10, 2026#3
Originally Posted by momoivanoff ↑
I was quoted $400+ for this and I did it myself. The subframe doesn't need to be dropped but lowered a little to get access.
$400 seems reasonable, hopefully I can find someone around that number. Do you know how many miles yours had at the time and how bad the rust was?
momoivanoffNJ · Nov 11, 2026#4
More than 200,000 miles,probably more than 250,000,I am not sure.Not much rust on it.
komichalCZ · Nov 11, 2026#5
My exact problem! The bushings are dead - when I disconnect the sway bar from the links on both ends then I can wiggle it very easily and it moves in the bushings and makes lot of clunking.

My trustworthy mechanic tried to lower the subframe to replace the bushings but even with the induction heater he was not able to get rid of the bolts. He said he can surely try harder but the bolts will most likely snap and from that moment onwards the job will get really expensive.

Maybe thats what your mechanic is suggesting. They know that these old rusty bolts will simply snap and they will be in much bigger job from that moment onwards.

So I am driving with this annoying clunking for over a year. I will get the car to the scrapyard anyway in 6 months as the bottom is rusty AF and the car will not make it through the state inspection without spending extra 1000-2000 USD for rear axle and bodywork etc. Simply not worth it.
lightdisc2Thread starterUS · Nov 12, 2026#6
Originally Posted by komichal ↑
My exact problem! The bushings are dead - when I disconnect the sway bar from the links on both ends then I can wiggle it very easily and it moves in the bushings and makes lot of clunking.

My trustworthy mechanic tried to lower the subframe to replace the bushings but even with the induction heater he was not able to get rid of the bolts. He said he can surely try harder but the bolts will most likely snap and from that moment onwards the job will get really expensive.

Maybe thats what your mechanic is suggesting. They know that these old rusty bolts will simply snap and they will be in much bigger job from that moment onwards.

So I am driving with this annoying clunking for over a year. I will get the car to the scrapyard anyway in 6 months as the bottom is rusty AF and the car will not make it through the state inspection without spending extra 1000-2000 USD for rear axle and bodywork etc. Simply not worth it.
Thank you for sharing this. I put so much money into this car with the intention of keeping it until 350-500k miles. I wish I knew about this problem. If I have to total my car because of some bushings I'm going to be so pissed.

How many miles have you driven with the clunking for the year+? Have you noticed any effects on handling, performance, or safety? Luckily I don't have inspections like that here but I've been told multiple times my rust is typical and not a safety issue. Also did the clunking start out like mine where you only hear it occasionally when turning over an incline?

If anyone else can add any information it would be very appreciated.