Yarisworld Archive

Package received from Taiwan!

75 posts · 26,535 views · page 2 of 2

Replies continued

ViolinNew Jersey · Aug 4, 2007#51
If the thought of building a harness scares you, there are plenty of harness builders around. Just explain exactly what you need - that schematic would help a lot.

It would be cheap compared to what you've already invested. Check here for some: http://www.hidplanet.com/forums/viewtopic.php?t=20144
ViolinNew Jersey · Aug 4, 2007#52
Originally Posted by GuySmily ↑
Wow, the 12v is on even with the car off?
Not the car (ignition), the light switch.



Originally Posted by GuySmily ↑
Violin, instead of resistors, have you tried using a small bulb like a turn signal bulb? I would just find somewhere to tuck it away, or even use it to light up the engine bay =p
Possible, although I've already drilled a hole in my dash for the LED, so I'm done.
GabLThread starterToronto · Aug 6, 2007#53
Just wanted to confirm, is the DRL in our current H4 bulb uses the high beam filament? If so, shouldn't the high beam wire and the DRL be the same with just different voltage supplied at different time? i.e. at DRL, a lower voltage is supplied, and at high beam, full 12V is supplied through the same wire? If this is the case, then I can just wire the high beam wire to the halogen bulb of the new HID unit using the same concept? Thanks in advance.
Chris07LBNew Jersey · Aug 7, 2007#54
The key word there is, in "our" headlights. Being as everything is seperate in your new kick ass one's, they may wire things differently right from the start.

I would look into Volins suggestion of someone making up a harness and figuring everything out for you. Might save you some stress in the long run.
taKutoToronto · Aug 7, 2007#55
the DRL uses the low-beam for us. You can confirm this by turning on/off your headlights at night near a wall where you can see the change is just the brightness when the headlights are turned on.

i should add, this is for my echo, which should not be different from the yaris but it might. The same method to check still applies.
Chris07LBNew Jersey · Aug 7, 2007#56
Well I would think its a no brainer for it to be a lower voltage off the LOW beam, beacuse although its a lower voltage, the beam PATTERN would be aim'd up if using the HIGH beam portion of the H4?

Violin may be able to shed a little more light here..
GabLThread starterToronto · Aug 7, 2007#57
I just checked the wire diagram for the Yaris, and it seems that taKuto is correct, the Yaris uses the Low Beam filament as DRL... which creates a bit of a problem. If I'm using the H4 common wire as the trigger for the HID, will this common wire be on when the car is supposed to be running on DRL? I can't seem to understand the diagram from Violin, as in the H4 plug, the H terminal is not linked to anywhere? GuySmily's diagram seems to be much simplier with just one relay?
Chris07LBNew Jersey · Aug 7, 2007#58
Well then, if you are expecting to keep the DRL box hooked up in your car, and splice off the regular plug to fire your HID's, it wont work. Keeping DRLs and having HID, will "strobe effect" your ballasts, and kill them over time.

Hence the reason for disconnecting the DRL box for anyone installing just a plug-n-play in their Yaris.
ViolinNew Jersey · Aug 8, 2007#59
I don't really have a solution to your DRL dilemma. Would it be legal to have a separate pair of lights, perhaps behind the grill, that come on whenever the ignition is switched on? That would be simple.

In my diagram, the car side H4 plug plugs into a female H4 plug that I purchased and integrated into the harness. See my DIY for parts suppliers.
taKutoToronto · Aug 8, 2007#60
You will only need one relay, and diodes for the low beam and high beam triggers which connect to the relay. You cannot use GuySmiley's harness since that's for positive trigger. You will need a negative triggered harness made. Wish I had the time to make you the schematic, but I'm sure you can find it somewhere.
Black YarisToledo, OH · Aug 8, 2007#61
dumb question.... but since we have city lights in the LB, could you just use those as you DRL? or can you hook up the high beam bulb on the same circute as the parking lights and use relays in a series to have them shut off when the lowbeam HID's come on..... only down fall to this will be no regular Highbeams at night
I can draw up a scamatic if you do not understand... but it will work, and you can keep your DRL disabled and run HID's :)
GabLThread starterToronto · Aug 8, 2007#62
Originally Posted by taKuto ↑
You will only need one relay, and diodes for the low beam and high beam triggers which connect to the relay. You cannot use GuySmiley's harness since that's for positive trigger. You will need a negative triggered harness made. Wish I had the time to make you the schematic, but I'm sure you can find it somewhere.
What's the difference between positive and negative trigger? And I thought I only need the low beam wire as trigger, as the high beam wire I will plug directly to the hagelon light.
taKutoToronto · Aug 8, 2007#63
positive trigger = a +12V wire is given power when the switch is on.
negative trigger = the ground wire is active when the switch is on.

toyotas are mostly negative triggered. Makes the harness a little different for constructing.

The high beam will get the common 12V and the high beam ground
The low beam (HID) will use a relay harness which will use the low beam and high beam grounds as a trigger wire.

Black Yaris, what are city lights? Do you mean the parking light? Is it a bulb that turns on when you flip the headlight switch one notch, and stays on during the low-beam switch?
Black YarisToledo, OH · Aug 8, 2007#64
Originally Posted by taKuto ↑
positive trigger = a +12V wire is given power when the switch is on.
negative trigger = the ground wire is active when the switch is on.

toyotas are mostly negative triggered. Makes the harness a little different for constructing.

The high beam will get the common 12V and the high beam ground
The low beam (HID) will use a relay harness which will use the low beam and high beam grounds as a trigger wire.

Black Yaris, what are city lights? Do you mean the parking light? Is it a bulb that turns on when you flip the headlight switch one notch, and stays on during the low-beam switch?
what you are calling a positive trigger is a normal neg(-) ground system
what you are calling a negative trigger is called a pos(+) ground

City lights are the these, I had this pic laying around, to explain city lights to someone else
Picture not included in this copy
ViolinNew Jersey · Aug 9, 2007#65
The reason I use three relays is so I can flash the high beams without the HIDs coming on. Worth the effort, I think.
taKutoToronto · Aug 9, 2007#66
When is that city light active? I don't have one for my echo so I wouldn't know anything about it.
ViolinNew Jersey · Aug 9, 2007#67
The first position on the light stalk turns it on, the next turns on the headlights. I used it (labled "arking lamp circuit" on my schematic) to trigger the one relay - if I used the low beam, they wouldn't turn off without shutting off the car. If Canadian models lack a city/parking lamp, my harness wouldn't work.
GabLThread starterToronto · Aug 10, 2007#68
Originally Posted by Violin ↑
The first position on the light stalk turns it on, the next turns on the headlights. I used it (labled "arking lamp circuit" on my schematic) to trigger the one relay - if I used the low beam, they wouldn't turn off without shutting off the car. If Canadian models lack a city/parking lamp, my harness wouldn't work.
We have parking light as well in Canadian models.
GabLThread starterToronto · Aug 22, 2007#69
Is it possible to wire the Fog Lights to become DRL? Just a though after talking to my friend. He did a retro fit to his Civic SiR with Audi A6 projector, and he wired his Fog to become DRL with the use of relays... I will ask him for more detail on that.
R0ME0Seattle, WA · Aug 24, 2007#70
GabL I went through a similar dilema with my Celica. i'd just retrofit a custom HID setup for the headlights with some grommets thats what i did and its works like a beauty. Also as someone pointed out that the 3prong is for a leveling switch. Pretty easy to wire up. If you're interested let me know I can teach you how to hook it up. It does wonders in the Celica! I might have to do this for the Yaris now. Do you have a link on where to buy these headlights? Additionally do you have more pics of the headlights? Is there no longer any permenant amber on the headlight just in the bulb? Please let me know. Thanks!
GabLThread starterToronto · Aug 28, 2007#71
Originally Posted by R0ME0 ↑
GabL I went through a similar dilema with my Celica. i'd just retrofit a custom HID setup for the headlights with some grommets thats what i did and its works like a beauty. Also as someone pointed out that the 3prong is for a leveling switch. Pretty easy to wire up. If you're interested let me know I can teach you how to hook it up. It does wonders in the Celica! I might have to do this for the Yaris now. Do you have a link on where to buy these headlights? Additionally do you have more pics of the headlights? Is there no longer any permenant amber on the headlight just in the bulb? Please let me know. Thanks!
R0ME0, do you still have the wire diagram of how you wire up your Celica? I do want to make the fog light the DRL and keep everything there.
I'm also interested to know how to wire up that auto leveling switch? Please post some pictures if you can. Thanks!
I got the headlights from Taiwan Yahoo auction as mentioned (tw.bid.yahoo.com). It doesn't have the permenant amber reflector at the side, also the side parking light is not on this headlight also. I will try to post some more pics later!
acdaaznNJ · Sep 23, 2007#72
So whatever happened to this project?
GabLThread starterToronto · Sep 24, 2007#73
It's on hold until I find out how to get the circuit working. hahaha!

Trying to get the fog light to become DRL, with on/off switch still function. My friend did that to his Civic SiR, so need to find time so we can sit down and look at it.

And thanks for following up, I will definitely post up some info once I get it done.
TrancosRtS Florida · Sep 24, 2007#74
Well, If i understand the DRL circuitry correctly, it's an independent wire that hooks to the headlamps power. So, in theory, you can re route the DRL power to the foglights. My Yaris doesn't have neither DRL nor Foglights, so I can't vouch for this to work. In theory, however, if you can find where the DRL circuit hooks up to the headlamp harness, you can just cut this connection and connect it to the foglights one instead.
GabLThread starterToronto · Sep 25, 2007#75
I think it's the other way, as there is only one wire going to the bulb, which is a H4 bulb, and it is the DRL module that regulates how much power to go to the bulb, i.e. DRL or Low Beam. So I cannot just hook this wire to the fog to make it DRL, else I will lose the Low Beam wire. This is how I understand the circuit diagram from the DIY section.