its illegal .. thats the answer i got :p
DIY: NST Short Shift Kit [NonStopTuning]
76 posts · 41,855 views · page 2 of 2
Replies continued
i love the way it shifts... sturdy , precise, shorter...i may miss the rubbery feel.. then again only takes less than 2 minutes to switch it back.. 👍 you rock nst!!
They are listed in the US as a business and if they are caught doing illegal stuff they will be fined to death and forced to close shop. Do the right thing and pay the duties imposed by your country. Speak to your country's officials if you have a problem with paying it, don't put your favorite company in a tough spot by asking them to do something illegal. They won't list it as a gift or lower the value.Originally Posted by marcus ↑yah it would have help if its sent as gift...so no other fees involve..
anyway duty with usps are not expensive.. if u go with fedex or ups.. u add 55$ + dutie.... and at canada post they only charge 5$+ duties
Does anybody know if this will work in the Echo Hatch (i.e. the previous generation Yaris)?
Thanks!
Thanks!
This will be in my to buy/ to do list.
I saw one at eBay for $96 + $8 shipping.
NST NonStopTuning Toyota Yaris Short Shift Kit
I saw one at eBay for $96 + $8 shipping.
NST NonStopTuning Toyota Yaris Short Shift Kit
this thing doesnt fit on a 2009 3dr LB...It doesnt rest far enough down so you put the cotter pin in...
PM sent. Let me know.Originally Posted by gmodder ↑this thing doesnt fit on a 2009 3dr LB...It doesnt rest far enough down so you put the cotter pin in...
Ok guys Upon Cali's request Iam posting what i did to make this work...Sorry my camera is screwed so no pics but dont think they are needed..
Basically from stock there is absolutely no way the device will sit far enough down so the cotter pin can slide in...So i put my toyota cap on and thought for about 2mins' (as long as can without getting a headache)
I pulled out my dremel and put the following bit on it..(I know but it was the only one i had to work with) http://www.dremel.com/en-us/Attachme...l.aspx?pid=562
I basically cut down the bottom side of the blk until i couldnot see any red left..I also had to cut a little off the edges..So now the blk is completely silver on the bottom...I did have to test fit about 4 times until i got it just right..Once i had enough cut down I had to press down on the blk pretty hard and it slid all the way down for the cotter pin to slide..Tested a short drive everything seems fine..took me about 20mins to do this...Maybe NST can look into this and make a ver.2 for us 08-09 owners...
Also 1 thing to point out...I dont think it is the depth of the channel on the blk its the edges that are stopping the thing from resting flat...so someone might try just fileing the edges down instead of the whole bottom side.
Basically from stock there is absolutely no way the device will sit far enough down so the cotter pin can slide in...So i put my toyota cap on and thought for about 2mins' (as long as can without getting a headache)
I pulled out my dremel and put the following bit on it..(I know but it was the only one i had to work with) http://www.dremel.com/en-us/Attachme...l.aspx?pid=562
I basically cut down the bottom side of the blk until i couldnot see any red left..I also had to cut a little off the edges..So now the blk is completely silver on the bottom...I did have to test fit about 4 times until i got it just right..Once i had enough cut down I had to press down on the blk pretty hard and it slid all the way down for the cotter pin to slide..Tested a short drive everything seems fine..took me about 20mins to do this...Maybe NST can look into this and make a ver.2 for us 08-09 owners...
Also 1 thing to point out...I dont think it is the depth of the channel on the blk its the edges that are stopping the thing from resting flat...so someone might try just fileing the edges down instead of the whole bottom side.
Thanks for the write up -- glad you got it to work.
Maybe a thinner version with and without a washer would fit both versions?
Maybe a thinner version with and without a washer would fit both versions?
Washer doesnt come in play until you are putting the Arm back on..That cotter pin has plenty of room to slide in..Originally Posted by cali yaris ↑Thanks for the write up -- glad you got it to work.
Maybe a thinner version with and without a washer would fit both versions?
hi all plp... perhaps I missed something... does this actually work on the new yaris 1.33 (100hp) model 2009??
thank you in advance
kind regards,
davide
thank you in advance
kind regards,
davide
I don't like the idea of spending close to $100 on something thats made for my car and having to shave it down to make it fit. But thats just me. I'll buy one if the fitting problems get fixed.
$98 for a little piece of aluminum? wtf?
The TRD one costs even more. Try making one yourself.Originally Posted by naossoan ↑$98 for a little piece of aluminum? wtf?
Where was the install moved to? Looks like I scored one, and will need installation instructions.
Here you go:Originally Posted by swidd ↑Where was the install moved to? Looks like I scored one, and will need installation instructions.
http://www.subcompactculture.com/200...nst-short.html
Links to http://www.subcompactculture.com/NST..._Products.html which ... does not exist.
Found this http://scionlife.com/forums/showthread.php?t=124859 instead -- usable!
Found this http://scionlife.com/forums/showthread.php?t=124859 instead -- usable!
After installing and running with it for a while, the gears became a bit stiffer to shit into and out of. Kinda like a "dry hump" to get over/into to get into the gates.
Sprayed down the whole NST and gear linkage and top of gear box with WD-40, and it shifts smooth as baby oil.
Are there any ill effects from just whimsically spraying WD-40 around at all places in the car? Avoiding surfaces that get hot, like the exhaust and engine block, can I safely spray WD-40 on everything else without messing up? (nuts and bolts, to keep from rusting)
Sprayed down the whole NST and gear linkage and top of gear box with WD-40, and it shifts smooth as baby oil.
Are there any ill effects from just whimsically spraying WD-40 around at all places in the car? Avoiding surfaces that get hot, like the exhaust and engine block, can I safely spray WD-40 on everything else without messing up? (nuts and bolts, to keep from rusting)
it says he DIY has been moved, but where did that sucker move to?
limey163, see my post 2 before yours, there's a better guide somewhere else.
Chino jumped ship in a snit in 2009. Removed everything he ever created, leaving us with several useless threads. But, as has been mentioned, post#71 contains a new link.Originally Posted by limey163 ↑it says he DIY has been moved, but where did that sucker move to?
The new version has an extra bracket to move the cables over as well. Mazilla posted a DIY with pictures on here recently. TRD has them, and I will have our version available very soon.
/topic
As for the above comment, for the record, Chino had good reason to do what he did, and he wasn't alone. At least include enough of the story so people understand and can make up their own minds, instead of just trying to make him look bad.
/topic
As for the above comment, for the record, Chino had good reason to do what he did, and he wasn't alone. At least include enough of the story so people understand and can make up their own minds, instead of just trying to make him look bad.
Thanks guys.
Also I notice there are 4 different shifter additions, the bushing kit, engine bay kit, and 2 cabin kits, do you need to have all four? I was thinking of grabbing the in-cabin short shifter kit but I don't want the car to feel off-balance since it's missing the other three.
Also I notice there are 4 different shifter additions, the bushing kit, engine bay kit, and 2 cabin kits, do you need to have all four? I was thinking of grabbing the in-cabin short shifter kit but I don't want the car to feel off-balance since it's missing the other three.
the bushing kit just stifens up the feel (takes out the slop) and for the under hood vs the in cabin kit, you can have one or the other or both. I think they both reduce throw buy around 25% or so. some people go really extreme and do both to reduce throw by about 50%
I honestly am going for the under hood kit because it is easier. I hope to make a youtube vid of my install. at the same time, it may be a while since i don't even have it yet (and it isn't available just yet either)
I honestly am going for the under hood kit because it is easier. I hope to make a youtube vid of my install. at the same time, it may be a while since i don't even have it yet (and it isn't available just yet either)
This is for the engine compartment SSK.... Anyone know were I can find the IN CABIN SSK DIY??? It's like the 'Great White Buffalo.....' HELP! Please 🤷Originally Posted by swidd ↑Links to http://www.subcompactculture.com/NST..._Products.html which ... does not exist.
Found this http://scionlife.com/forums/showthread.php?t=124859 instead -- usable!