Yarisworld Archive

TRD Sport Seats - JDM

13 posts · 6,489 views

KS SOLOOriginal postKansas · Jul 20, 2007#1
The good news is my new TRD Sports seats arrived from Japan (ordered them in Feb.) and were installed by the dealer. 👍

The bad news is my SRS airbags are disabled and my seatbelt light flashes.😠

I searched our site and really did not see anyone who has replaced their stock seats in a LB with either aftermarket or TRD's and have a fix for this issue. 🤷

Has anyone done this, and I have read all the wiring DIY's and those may be my last resort.

Thanks!!

Replies 12

cleongSingapore · Jul 20, 2007#2
I think if you unplugged anything electrical whilst taking out the seats from your car, you might have to wire plugs to close the loop again (much like those guys who changed to aftermarket steering wheels without airbags).
ShijimaCanada · Jul 20, 2007#3
Its probably what he said, and on a side note, WHERES THE PICS!?!
regimeNew London, CT · Jul 20, 2007#4
Originally Posted by Shijima ↑
..., and on a side note, WHERES THE PICS!?!
i 2nd that!!!
tk-421Dagobah · Jul 20, 2007#5
ASHRAFHouston, TX · Jul 21, 2007#6
Originally Posted by tk-421 ↑
x2
red-jdmJakarta (indonesia) · Jul 22, 2007#7
The bad news is my SRS airbags are disabled and my seatbelt light flashes.😠

I searched our site and really did not see anyone who has replaced their stock seats in a LB with either aftermarket or TRD's and have a fix for this issue. 🤷

Has anyone done this, and I have read all the wiring DIY's and those may be my last resort.

Thanks!![/QUOTE]

I don't know if you have already solved your problem but if you haven't :
Did you buy the TRD bracket and rail seats?
If you do but your seatbelt light is on, then you must have forgotten to re-connect the wire which is located right underneath the driver seat to the wiring fitted on the bracket and seat rail
punchBarrie, ontario · Jul 22, 2007#8
also, on other vehicle people have been wiring some type of transister into the srs wiring from the seat, search the net there are solutions...
Black YarisToledo, OH · Jul 22, 2007#9
some pl have been taking there harness and sensors from there stock seats and installing them in to there new seats... I will find the thread.....
cali yarisCanoga Park, CA · Jul 22, 2007#10
yes, you need a resistor for the pressure/weight sensor in the passenger seat (after ripping it out of your stock seat, of course). that's the only way to have the airbag work correctly, it needs to "think" someone is sitting there. Of course, that's an "always on" scenario, but that's better than disabling your passenger's bag.

At least on the Scions, the drivers side has a positioned sensor, so the car "knows" how far you are from the bag in the wheel (timing is everything, and bad timing can be lethal in this case). This can be repositioned on the new rail, but take note of where it was before you make the switch.

There has been some discussion as to whether the airbag system deploys at all if one component is compromised or disconnected. I have not been able to get a definitive answer (probably because they don't want you to mess with such an important safety feature).
RossPPaphos, Cyprus · Jul 22, 2007#11
there is a trd air bag canceller. You can get it from japan parts
smokinyarisSoCal · Jul 22, 2007#12
this thread is very interesting since i wanted to throw my recaros off my EVO........
elsteverino889MIA! · Jul 23, 2007#13
PICS!