vettehighOriginal postNY · Mar 15, 2025#1My girls 2009 Yaris Hatchback 5-speed 1.5L has a 1/4 inch exhaust leak coming from the passenger rear where the hanger is. If that can not be welded, you need to get the complete exhaust from engine back for around $1200 from the dealer which is nuts.
Any input would be great 👍
Replies 24
WeeYariGeorgetown, Ontario, Canada · Mar 15, 2025#2Replacement pipes from the resonator back to muffler flange are available. Replacing that piece plus labour should be less than $200.
WeeYariGeorgetown, Ontario, Canada · Mar 15, 2025#3I currently am using this piece. American pricing is a hell of a lot less.
1 attachment not included in this copy
vettehighThread starterNY · Mar 15, 2025#4WeeYariGeorgetown, Ontario, Canada · Mar 15, 2025#5Pipe is cut where I've drawn the line. New piece replaces the length to the right of line. Resonator is immediately to the left.
1 attachment not included in this copy
vettehighThread starterNY · Mar 15, 2025#6 Originally Posted by
WeeYari ↑ Replacement pipes from the resonator back to muffler flange are available. Replacing that piece plus labour should be less than $200.
Originally Posted by
WeeYari ↑ Pipe is cut where I've drawn the line. New piece replaces the length to the right of line. Resonator is immediately to the left.
And that is a direct connect to the rear muffler? Also, I'm in NY and that replacement pipe is from Canada, can't find it here in the states
WeeYariGeorgetown, Ontario, Canada · Mar 15, 2025#7Yes, it's direct connect to muffler. I know it's Canadian, but American sources can be found.
vettehighThread starterNY · Mar 15, 2025#8WeeYariGeorgetown, Ontario, Canada · Mar 15, 2025#9Yes it is. I've was searching and spotted for cheaper on eBay store for upswautoparts in New Jersey.
vettehighThread starterNY · Mar 15, 2025#10 Originally Posted by
WeeYari ↑ Yes it is. I've was searching and spotted for cheaper on eBay store for upswautoparts in New Jersey.
May you send me the link. I put the part # in, but did not come up via upswautoparts
Many thanks also for helping me 🎉
vettehighThread starterNY · Mar 15, 2025#11WeeYariGeorgetown, Ontario, Canada · Mar 15, 2025#12vettehighThread starterNY · Mar 15, 2025#13 Originally Posted by
WeeYari ↑
Thank you again. Just wonder if the quality of the metal they sell is bad, due to their prices being so low
WeeYariGeorgetown, Ontario, Canada · Mar 15, 2025#14Metal on aftermarket is not as good as OEM, but good for several more years of running. Just have the union between old and new clamped, not welded. Cheap enough that if it fails, replace again. Also, a welded joint on old pipe almost certainly guarantees that your next point of failure will be that weld.
vettehighThread starterNY · Mar 15, 2025#15 Originally Posted by
WeeYari ↑ Metal on aftermarket is not as good as OEM, but good for several more years of running. Just have the union between old and new clamped, not welded. Cheap enough that if it fails, replace again. Also, a welded joint on old pipe almost certainly guarantees that your next point of failure will be that weld.
👍
I'm taking her Yaris in on Friday and will post back to you that afternoon. Hopefully the tiny crack can be welded, if not, then I will get that pipe
Just a word to the wise... When you replace the muffler, and you will soon, get an OEM muffler. I made the mistake of saving a buck with an aftermarket muffler . Between the edge of it unavoidably rubbing and bouncing against the underside of the car making an annoying noise coupled with that it sounded like hollow tin can, i tore it off and threw it in the steel scrap dumpster at work after one week. But hey, you might like that...I didn't.
vettehighThread starterNY · Mar 17, 2025#17 Originally Posted by
bairjo ↑ Just a word to the wise... When you replace the muffler, and you will soon, get an OEM muffler. I made the mistake of saving a buck with an aftermarket muffler . Between the edge of it unavoidably rubbing and bouncing against the underside of the car making an annoying noise coupled with that it sounded like hollow tin can, i tore it off and threw it in the steel scrap dumpster at work after one week. But hey, you might like that...I didn't.
I'm OE 99% of the time. Yes, I would get OE muffler along with OE nuts/bolts/gaskets too
vettehighThread starterNY · Mar 17, 2025#18 Originally Posted by
WeeYari ↑ Metal on aftermarket is not as good as OEM, but good for several more years of running. Just have the union between old and new clamped, not welded. Cheap enough that if it fails, replace again. Also, a welded joint on old pipe almost certainly guarantees that your next point of failure will be that weld.
If there are other cracks in the system, I would think about this Magnaflow system for her along with new OE muffler. I can get it for around $700 shipped. Only issue I see, will this still pass NYS computer inspection without being CARB compliant?
https://www.magnaflow.com/products/5...E3VC3N_ug6LZPL WeeYariGeorgetown, Ontario, Canada · Mar 17, 2025#19^ Yes
vettehighThread starterNY · Mar 18, 2025#20 Originally Posted by
WeeYari ↑ ^ Yes
Just to double check, will this Magnaflow system pass NYS computer inspection without being CARB compliant? Don't want to go through all the expense and trouble then have it hooked up to the NYS inspection computer and have an issue
WeeYariGeorgetown, Ontario, Canada · Mar 18, 2025#21I may have jumped the gun on that by saying yes. Did a bit of reading and noticed NY requires CARB compliance. I don't know how anal your inspection sites are and if they'd bother looking for the stamp on the cat.
Your system is probably good. My 2006 with 411,000 rust belt kms on her is still original forward of the resonator.
vettehighThread starterNY · Mar 18, 2025#22 Originally Posted by
WeeYari ↑ I may have jumped the gun on that by saying yes. Did a bit of reading and noticed NY requires CARB compliance. I don't know how anal your inspection sites are and if they'd bother looking for the stamp on the cat.
Your system is probably good. My 2006 with 411,000 rust belt kms on her is still original forward of the resonator.
They won't look at the stamp, so the computer test they run will not be able to detect non-carb compliant right? Thank you
vettehighThread starterNY · Mar 19, 2025#23I wish they had 304 SS instead of 409 SS. My other vehicles are T-304. I could only find 409 SS for the Yaris. Living in the NE with all the salt, I wonder how long that 409 system would last???? 😲
vettehighThread starterNY · Mar 31, 2025#24Have all my items now. Went with all Toyota OE hardware (hangers, springs, bolts, gaskets) along with Toyota OE muffler. All this paired with the Magnaflow 52581 system. I'm keeping the original cat (only 65K miles) and I'll set that in my garage. Was thinking of selling it, but doubt I would get much so it's best just to keep
vettehighThread starterNY · Apr 18, 2025#25I installed the new system yesterday. Super nice Mag system along with OE muffler and hardware. Any idea what the old cat is worth for scrap?