Yarisworld Archive

PCV valve preventative maintenance

11 posts · 14,677 views

snowblowerOriginal postCanada · Feb 23, 2024#1
Is there a consensus on preventative maintenance of the 1NZ-FE PCV valve? Clean only? Replace? Never a problem, forget about it?

Replies 10

komichalCZ · Feb 23, 2024#2
On 2SZ-FE I just pop it out like once a year, spray through it with brake cleaner and try to blow air through it - it should go easily one direction and it should not go at all in the opposite direction. If that is the case then it can be safely placed back.
BilliamUSA · Feb 27, 2024#3
Not worth the hassle. It's a $10 part from your local dealer. Replace it.
snowblowerThread starterCanada · Feb 27, 2024#4
That's what I've always done for my Hondas. This is my first Toyota. I may just do that. We'll see. I'm trying not to break the parts bank with this car.

Do you happen to know if there is a spring in Toyota's PCV valve for the 1NZ-FE, or just a simply check valve? I'm more inclined to replace PCV valves that have a spring due to the spring relaxing with age.

Originally Posted by Billiam ↑
Not worth the hassle. It's a $10 part from your local dealer. Replace it.
BilliamUSA · Mar 1, 2024#5
Originally Posted by snowblower ↑
That's what I've always done for my Hondas. This is my first Toyota. I may just do that. We'll see. I'm trying not to break the parts bank with this car.

Do you happen to know if there is a spring in Toyota's PCV valve for the 1NZ-FE, or just a simply check valve? I'm more inclined to replace PCV valves that have a spring due to the spring relaxing with age.
It's been 2 or 3 years since I replaced it and frankly don't remember. But I'm fairly certain it's just a check valve. There just wasn't a significant price difference between aftermarket and OEM....especially when you're taking about a $10 part.
esse10richmond TX. · Mar 7, 2024#6
once a year just remove, clean with denatured alcohol or contact cleaner and put back.
alanwagenTexas · Mar 7, 2024#7
How easy is it to get to though? I can't find it. 2015 Yaris 1.5l L
snowblowerThread starterCanada · Mar 16, 2024#8
I took mine out finally. I cleaned it with brake clean. Sprayed it and let it soak in cleaner for a while (my wife will never know what that egg cup was used for). It was leaking a bit of reverse flow before cleaning. Leak free after cleaning. The service manual just says it should flow in one direction freely, not flow at all in the other direction. I'm going to leave it at that. Also, there is a spring in it. I can see it in the service manual diagram and I can tell when inspecting the physical valve. The inlet side of the valve will depress easily and spring back to its original position, if anyone cares to see for themselves.
snowblowerThread starterCanada · Mar 16, 2024#9
Originally Posted by alanwagen ↑
How easy is it to get to though? I can't find it. 2015 Yaris 1.5l L
In my 2014 with a 1NZ-FE engine, it's at the back right of the engine at the corner of the valve cover. You have to remove the plastic engine cover to get at it.
snowblowerThread starterCanada · Mar 16, 2024#10
Finally, the service manual says 27 N-M, 20 ft-lb. It also says "precoated part". Which I expect means thread sealant. So I'm reinstalling mine with Permatex High Temp thread sealant.
snowblowerThread starterCanada · Mar 16, 2024#11
Originally Posted by snowblower ↑
Finally, the service manual says 27 N-M, 20 ft-lb. It also says "precoated part". Which I expect means thread sealant. So I'm reinstalling mine with Permatex High Temp thread sealant.
Don't follow that 20 ft-lb blindly. The "precoating" on the factory part is probably dry. With a liquid sealant it will be lower. I put a torque wrench on it out of curiosity. I wasn't conformortable going beyond about 15 ft-lb. It was very snug.