Hard to find an aftermarket console box/armrest for an automatic 2012 LE. Anybody ever had the same issue ?
2012 LE automatic aftermarket armrest
17 posts · 10,578 views
Replies 16
I have the OEM option arm rest in my 2014, works fine. I don't think it was available in Canada, I had to buy one out of the US on eBay. Part number is PT413-52120.
i find em now n then if someone really wants one ill keep my eyes out..they are HARD and not comfy
I found one on Amazon for Yaris2006-2011. Checked measurements and I chanced it. Might have to modify it a little.Originally Posted by mitch9521 ↑I have the OEM option arm rest in my 2014, works fine. I don't think it was available in Canada, I had to buy one out of the US on eBay. Part number is PT413-52120.
Thanks
I found one on Amazon for Yaris2006-2011. Checked measurements and I chanced it. Might have to modify it a little.Originally Posted by sh0rtlife ↑i find em now n then if someone really wants one ill keep my eyes out..they are HARD and not comfy
Thanks
Stay away. These aftermarket armrests are cheap pieces of crap. Nobody has really found a decent one. You can try it, your money, but prepare to be disappointed.
I don't expect any quality from China but couldn't find anything decent on this continent. Worst scenario, I'll make myself one.Originally Posted by WeeYari ↑Stay away. These aftermarket armrests are cheap pieces of crap. Nobody has really found a decent one. You can try it, your money, but prepare to be disappointed.
Actually cancel your order. 06-11 simply will not fit in a '12.
You sure ? By the looks of it, looks like somewhat of a fit. I have a round cavity just behind the hand brake. Mine is automatic, not standard shift and it was rebuilt. I wonder if I have the original 2012 gear box or another year instead.Originally Posted by WeeYari ↑Actually cancel your order. 06-11 simply will not fit in a '12.
Yes I am sure. Both Gen2 and Gen3 have that rear cup holder that the armrest fits into. However, there are molding differences in the centre console which will prevent an Gen2 armrest from properly seating into the Gen3 console. There is a reason why fitment guides specify 06-11, or 12+.
Even my OEM+ one had to be fixed, the hinge on it is plastic and snapped off in the cold on me so I permanently bolted it down by drilling two holes through the storage compartment and getting some longer bolts from lowe's with some blue loctite. I can't tilt it back anymore but its been rock solid for 3+ years now lolOriginally Posted by WeeYari ↑Stay away. These aftermarket armrests are cheap pieces of crap. Nobody has really found a decent one. You can try it, your money, but prepare to be disappointed.
I followed your advice and wasn't too late to cancel it. I'll keep looking around or make myself one.Originally Posted by WeeYari ↑Yes I am sure. Both Gen2 and Gen3 have that rear cup holder that the armrest fits into. However, there are molding differences in the centre console which will prevent an Gen2 armrest from properly seating into the Gen3 console. There is a reason why fitment guides specify 06-11, or 12+.
Thanks
No choice but to make my own.
Picture not included in this copy
Picture not included in this copy
Picture not included in this copy
It's held in place through a longer M6 x 70 mm bolt and perforated piece of 1/2" plywood shaped like the rear half moon cup hole in the back if original console. I then used strap iron and short wood screws tying the new console/armrest to the low original plastic console.
Cover is apiece of 1/2" plywood, 2" soft foam and imitation leather stapled to the underneath of the plywood. Painted the wood box. Screwed a cupboard door catch so the cover snaps in the wood box . Two small hinge so I can lift the cover and put stuff in the box. Don't need to spend countless hours on the internet to look for a comfortable armrest/center console anymore. Both elbows can nom rest while driving. Much more comfortable.
Thanks everyone for their help,
danyboy
Picture not included in this copy
Picture not included in this copy
Picture not included in this copy
It's held in place through a longer M6 x 70 mm bolt and perforated piece of 1/2" plywood shaped like the rear half moon cup hole in the back if original console. I then used strap iron and short wood screws tying the new console/armrest to the low original plastic console.
Cover is apiece of 1/2" plywood, 2" soft foam and imitation leather stapled to the underneath of the plywood. Painted the wood box. Screwed a cupboard door catch so the cover snaps in the wood box . Two small hinge so I can lift the cover and put stuff in the box. Don't need to spend countless hours on the internet to look for a comfortable armrest/center console anymore. Both elbows can nom rest while driving. Much more comfortable.
Thanks everyone for their help,
danyboy
3 attachments not included in this copy
👍 That's works
Glad you made me cancel my Chinese armrest order.Originally Posted by WeeYari ↑👍 That's works
Thanks
I don't hate it lol, my shifter would get in the way though
Of course, if I had a standard shift I couldn't have done this.Originally Posted by mitch9521 ↑I don't hate it lol, my shifter would get in the way though