mjl1297Original postTennessee · Aug 9, 2022#1I have the car mentioned above built in Japan for the US market. The wiring harness is already run and I was wondering if anyone could recommend a good set of plug and play aftermarket lights and reference any installation threads/videos that might be useful for this particular model?
Many thanks.
Replies 23
mitch9521Red Deer, AB · Aug 9, 2022#2Morimoto XB
mjl1297Thread starterTennessee · Aug 9, 2022#3Not a complete kit--no bezels or mounting hardware as far as I can tell.
mannycheckersNYC · Aug 10, 2022#4I doubt you will find a complete kit.
For my 2009, I bought fog light housings, bezels, and bulbs on ebay. I looked up the OEM part numbers on Toyota online part store. I also purchased a toyota wiring assembly, of which I spliced with the fog light wiring, to connect the fog lights to the engine-side fuse panel (behind the battery).
From there, I purchased a steering column stock with the fog light switch, installed the correct fuse (inside fuse panel), and I installed a relay.
Attached is a guide that I followed. Should be very similar for a 2014.
mitch9521Red Deer, AB · Aug 12, 2022#52012+ Yaris' are all pre-wired for fogs, get a pair from a junkyard or rockauto and a multifunction turn switch from a Toyota of the same era with fogs and they'll work. I got my switch from a 2010 Tundra. Even the fog light indicator in the cluster works.
sh0rtlifepacific north WET · Aug 15, 2022#6the set i got off ebay was non desript but was as good as oem even with glass lenses
mjl1297Thread starterTennessee · Jan 8, 2023#7Actually, I did find a complete kit and one that is OEM compatible.
I installed the lights in the proper place and connected them to the two wiring connectors which were already hanging there since the 2014 is pre-wired for fogs.
Now I have a push-in push-out switch to go in the spot recently vacated by a dummy plate on my dashboard but where do I find the connector that should already be there to plug into the back of that switch?
Thanks in advance.
sh0rtlifepacific north WET · Jan 9, 2023#8 Originally Posted by
mjl1297 ↑ Actually, I did find a complete kit and one that is OEM compatible.
I installed the lights in the proper place and connected them to the two wiring connectors which were already hanging there since the 2014 is pre-wired for fogs.
Now I have a push-in push-out switch to go in the spot recently vacated by a dummy plate on my dashboard but where do I find the connector that should already be there to plug into the back of that switch?
Thanks in advance.
do yourself a favor and get the fog headlight stalk either new or used this way the fog light on the dash will light..also makes controling them easier
mjl1297Thread starterTennessee · Jan 9, 2023#9How would I be doing myself a favour as it still seems there would be a connection up top that needs to be made somewhere even with the stalk?
Anyone else?
Really don't understand why it is so hard to get straight answers on this topic.
mitch9521Red Deer, AB · Jan 9, 2023#10 Originally Posted by
mjl1297 ↑ How would I be doing myself a favour as it still seems there would be a connection up top that needs to be made somewhere even with the stalk?
Anyone else?
Really don't understand why it is so hard to get straight answers on this topic.
There is no connector behind the filler panels. The fog light trigger wires run to the harness on the multifunction turn switch. Go grab a multifunction turn switch from a compatible vehicle that has the fog lights built in, swap it on and it will work.
mjl1297Thread starterTennessee · Jan 9, 2023#11So you're saying the only way to do this is to take the entire steering column assembly apart?!?
There has got to be another way.
sh0rtlifepacific north WET · Jan 10, 2023#12 Originally Posted by
mjl1297 ↑ So you're saying the only way to do this is to take the entire steering column assembly apart?!?
There has got to be another way.
in fact you just need to pull 2 covers and the air bag and make 2 connections
thetutMontreal · Jan 10, 2023#13mjl1297Thread starterTennessee · Jan 10, 2023#14And that video truly applies to my 2014 Toyota Yaris? Just want to make certain there are no unwelcome surprises once the wheel comes off.
mjl1297Thread starterTennessee · Jan 10, 2023#15Is the STANDARD MOTOR PRODUCTS CBS1234 multifunction turn switch compatible? I don't have the time to try and run one to ground through the salvage yards.
mjl1297Thread starterTennessee · Jan 10, 2023#16Looks like it does!
mitch9521Red Deer, AB · Jan 10, 2023#17That tutorial is 90% accurate for 3rd gens too, BUT the airbag on the steering wheel is held together with some silver tabs you need to press with a screwdriver, kind of a pain to do but its not too bad. Otherwise its the same procedure.
Be very careful with the clockspring. Its not cheap if you mess it up, highly recommend using some painters tape like in the video to secure it so you don't accidentally move it. Also no, you do not need threadlocker on the steering wheel nut, just snug it up and it will be fine.
mjl1297Thread starterTennessee · Jan 10, 2023#18Well, I was good to go until I saw the "90% accurate" and the "kind of a pain to do". Sounds like a REAL headache in the making...and then there's the clockspring.
I think I will continue to look around and see if there isn't another way. A way that apparently can't be found in this forum.
Thanks anyway guys.
sh0rtlifepacific north WET · Jan 10, 2023#19i could have sworn the wheel doesnt need to come off, just that the bag need to be out of the way to bolt in the switch, and the clock spring needs nothing more than plugged into
WeeYariGeorgetown, Ontario, Canada · Jan 10, 2023#20😎
Originally Posted by
sh0rtlife ↑ i could have sworn the wheel doesnt need to come off, just that the bag need to be out of the way to bolt in the switch, and the clock spring needs nothing more than plugged into
He is talking about a difference between 2nd and 3rd gen.
sh0rtlifepacific north WET · Jan 11, 2023#21 Originally Posted by
WeeYari ↑ 😎
He is talking about a difference between 2nd and 3rd gen.
yeah i know but doesnt the 3rd gen still have the same pre wired clock spring that only needs plugged into? and the only reason you need to pull the wheel is to swap the rear cover?
thetutMontreal · Jan 11, 2023#22mitch9521Red Deer, AB · Jan 11, 2023#23 Originally Posted by
mjl1297 ↑ Well, I was good to go until I saw the "90% accurate" and the "kind of a pain to do". Sounds like a REAL headache in the making...and then there's the clockspring.
I think I will continue to look around and see if there isn't another way. A way that apparently can't be found in this forum.
Thanks anyway guys.
If you're tapping out over a couple of clips that require a bit of patience to pop, maybe modifying cars isn't for you. 🤷
mjl1297Thread starterTennessee · Jan 12, 2023#24 Originally Posted by
thetut ↑
Not really. The alternate approach is one worth considering though!
Originally Posted by
mitch9521 ↑ If you're tapping out over a couple of clips that require a bit of patience to pop, maybe modifying cars isn't for you. 🤷
No, just don't want to go into a project like this unless I am 100% properly prepared especially since this is my daily driver.