Yarisworld Archive

High beam indicator stopped working

8 posts · 8,929 views

teddyOriginal postOntario, Canada · Jul 7, 2021#1
I noticed the other day I was driving with my high beams on, turns out the blue indicator in the dash isn't lighting up anymore. Is this simple enough to replace? What part would I need to buy?

The garage I take my car into replaced my headlight bulbs with LEDs a few months back. I had a blown bulb and they asked if I'd like to swap them out for LED, so I figured why not. I'm not sure if this would contribute to it. I'm about 95% sure the high beam indicator was working since.

Replies 7

mitch9521Red Deer, AB · Jul 7, 2021#2
As far as I know all of the indicator lights on the cluster are LED. I doubt the LED blew but you can pull the cluster out and check the circuit board on the back of it.
TommyWasabiAlabama · Aug 21, 2022#3
Did you ever figure this out? I replaced my headlights with LED's as well and I'm experiencing the same problem.
teddyThread starterOntario, Canada · Aug 22, 2022#4
Originally Posted by TommyWasabi ↑
Did you ever figure this out? I replaced my headlights with LED's as well and I'm experiencing the same problem.
Unfortunately no. I ultimately went back to the original non-LED bulbs. The LED lights had flicker in the DRL and were way too bright. Once I was back on the old bulbs the indicator worked again.
TommyWasabiAlabama · Aug 22, 2022#5
Originally Posted by teddy ↑
Unfortunately no. I ultimately went back to the original non-LED bulbs. The LED lights had flicker in the DRL and were way too bright. Once I was back on the old bulbs the indicator worked again.
I did some digging on the interwebs last night and it looks like most with this problem added a resistor in line and it fixed the problem. Apparently the LED's can cause some tricky problems. Anyway, I found a solution that essentially is a plug in. Just in case you ever want to go back to LED's in the future.

There are various ways to do this but this will work as a plug and play solution:
https://www.superbrightleds.com/moto...-load-resistor
teddyThread starterOntario, Canada · Aug 22, 2022#6
Originally Posted by TommyWasabi ↑
I did some digging on the interwebs last night and it looks like most with this problem added a resistor in line and it fixed the problem. Apparently the LED's can cause some tricky problems. Anyway, I found a solution that essentially is a plug in. Just in case you ever want to go back to LED's in the future.

There are various ways to do this but this will work as a plug and play solution:
https://www.superbrightleds.com/moto...-load-resistor

Huh, that looks simple enough. I wouldn't go back to LEDs - the housing isn't designed for them so at night I was blinding oncoming traffic.



I'm waiting for my Corolla Hybrid to come in, so will be saying good bye to Yaris after almost 15 years :)
sh0rtlifepacific north WET · Aug 22, 2022#7
you dont even need a real resistor just 2 tiny 12v to 3v resistors paired up run from the LOW to ground on the bulb socket...its how i fixed my HID's and its been since dec with no issues

to be clear im talking aboutthe same resistors you get in a bulk pack of LED's

i belive what i used was a pair of 1ohm

Picture lost · www.bpesolutions.com
TommyWasabiAlabama · Aug 24, 2022#8
Originally Posted by sh0rtlife ↑
you dont even need a real resistor just 2 tiny 12v to 3v resistors paired up run from the LOW to ground on the bulb socket...its how i fixed my HID's and its been since dec with no issues

to be clear im talking aboutthe same resistors you get in a bulk pack of LED's

i belive what i used was a pair of 1ohm

Picture lost · www.bpesolutions.com
Good stuff, I know I have a few resistors some where...