Yarisworld Archive

Lowing Springs vs Coilovers

61 posts · 56,316 views · page 2 of 2

Replies continued

06YarisRSThread starterFredericton, New Brunswick, Canada · Jul 24, 2020#51
Originally Posted by ern-diz ↑
This is very interesting. Before installing the Bilsteins, which have almost eliminated all of the rub I had, I found that it was always my front wheels that would rub, never the rear.
Well, I'm really glad I don't have any rubbing and I put it through a serious test earlier this evening. I found the bumpiest part of our road around here and tried to see if it would rub. I steered hard into bumps and dips in the road, loading each corner. I have no idea how close it comes to rubbing. The car is utterly transformed. It feels like it's on rails, without any jarring. I know if sounds absurd, but my car is both tighter and seemingly quieter than before. I can't explain it. I expected plastic rattling, dashboard and trim rattling...nothing.

I'm going to let the springs settle in. If the car doesn't come down a tiny bit, I may lower another 1/4" or so. I think I have the perfect balance (height and shock damping) for our road conditions.

Picture not included in this copy

Picture not included in this copy

Picture not included in this copy
Kaotic LazagnaCentral Valley, CA · Jul 25, 2020#52
Those dampers are probably doing a better job of absorbing impacts, so that's probably why you're getting a quieter ride. I'd go a little lower, but like you said earlier, you might be pushing the limit for your local road conditions.

Do you have any chassis bracing by chance? Oddly enough, it made my ride smoother. I think someone told me it deals with frequency balance or something like that. lol
06YarisRSThread starterFredericton, New Brunswick, Canada · Jul 25, 2020#53
Originally Posted by Kaotic Lazagna ↑
Those dampers are probably doing a better job of absorbing impacts, so that's probably why you're getting a quieter ride. I'd go a little lower, but like you said earlier, you might be pushing the limit for your local road conditions.

Do you have any chassis bracing by chance? Oddly enough, it made my ride smoother. I think someone told me it deals with frequency balance or something like that. lol
I believe they are doing a better job of dampening. When I had my exhaust done, I had added in a cylindrical straight through muffler. It was toward the back of the tunnel. The piping form there back to the axle is not exactly tucked up. Right now I have about 3" to the road at the lowest point of the exhaust. If I decided to lower, I might want to remove that cylindrical muffler and have the piping tucked up better. Right now, there are no issues with road contact, though.

I was out again this evening for a drive. All I can say is.. WOW! Even though I haven't gotten an alignment, the car is a sled on rails. Incredible difference!
ern-dizCA all day · Jul 27, 2020#54
So happy to hear about the improvement. Lower or not, it looks superb with the last adjustment you made. I'd personally go for a little more, but it's win-win either way.
06YarisRSThread starterFredericton, New Brunswick, Canada · Jul 27, 2020#55
Originally Posted by ern-diz ↑
So happy to hear about the improvement. Lower or not, it looks superb with the last adjustment you made. I'd personally go for a little more, but it's win-win either way.
Thanks Ernie. I do want to go a touch lower. Interestingly, I am at the lowest setting in the back. I did however use the rubber spring pad from the OE set up. I bolted the HSD spring retainer on top of it. The rubber pad is about 1/4" thick when compressed, I expect. I think if I remove the rubber spring pad and take out the locking ring from the HSD spring retainer, I could get another 1/2" to 3/4". If I remove the spring perch and locking ring, and set the springs right down on the bottom of the spring retainer, I could probably get a whole inch. I may yet do all of the stated. The front has at least another 1/2 drop capability. After that and I'd be running into the end link bracket on the damper.

I'm not sure of the appropriate terms in my explanation above, so here's a labeled pic of what I call the parts:

Picture not included in this copy
ern-dizCA all day · Jul 28, 2020#56
Originally Posted by 06YarisRS ↑
Thanks Ernie. I do want to go a touch lower. Interestingly, I am at the lowest setting in the back. I did however use the rubber spring pad from the OE set up. I bolted the HSD spring retainer on top of it. The rubber pad is about 1/4" thick when compressed, I expect. I think if I remove the rubber spring pad and take out the locking ring from the HSD spring retainer, I could get another 1/2" to 3/4". If I remove the spring perch and locking ring, and set the springs right down on the bottom of the spring retainer, I could probably get a whole inch. I may yet do all of the stated. The front has at least another 1/2 drop capability. After that and I'd be running into the end link bracket on the damper.

I'm not sure of the appropriate terms in my explanation above, so here's a labeled pic of what I call the parts:

Picture not included in this copy
From what you describe, it doesn't sound like that would impact their performance at all, right? The spring sitting down on the retainer is how it comes from the factory. If you're looking for some extra low, sounds like a good way to do it.
06YarisRSThread starterFredericton, New Brunswick, Canada · Jul 29, 2020#57
Originally Posted by ern-diz ↑
From what you describe, it doesn't sound like that would impact their performance at all, right? The spring sitting down on the retainer is how it comes from the factory. If you're looking for some extra low, sounds like a good way to do it.
Yep. Shouldn't affect performance. As soon as I'm done with my liftgate, the car's getting jacked up and the rings removed. I'll drop the front maybe another 1/2" too. 👍 After all, I'm going to a car show (Stance East) in Moncton, NB on Saturday. Not a big fan of super dropped cars or crazy camber, but it should be a fun show nonetheless.
ern-dizCA all day · Jul 29, 2020#58
Originally Posted by 06YarisRS ↑
Yep. Shouldn't affect performance. As soon as I'm done with my liftgate, the car's getting jacked up and the rings removed. I'll drop the front maybe another 1/2" too. 👍 After all, I'm going to a car show (Stance East) in Moncton, NB on Saturday. Not a big fan of super dropped cars or crazy camber, but it should be a fun show nonetheless.
I'm with you there. Fun to connect with people in all aspects of car culture, even if it's not my cup of tea.
06YarisRSThread starterFredericton, New Brunswick, Canada · Jul 30, 2020#59
Originally Posted by ern-diz ↑
I'm with you there. Fun to connect with people in all aspects of car culture, even if it's not my cup of tea.
For sure. I was cruising out of Saint John yesterday and was passed by a right hand drive Supra Turbo. I'm guessing around a 2006. The car looked very tastefully 'stanced'. I'm so hoping that the car is going to be at the show on Saturday.
ern-dizCA all day · Jul 30, 2020#60
Originally Posted by 06YarisRS ↑
For sure. I was cruising out of Saint John yesterday and was passed by a right hand drive Supra Turbo. I'm guessing around a 2006. The car looked very tastefully 'stanced'. I so hoping that the car is going to be at the show on Saturday.
Fingers crossed! I'm hoping for one of your usually detailed posts --but in the photo section, after the meet! 😁
06YarisRSThread starterFredericton, New Brunswick, Canada · Jul 30, 2020#61
Originally Posted by ern-diz ↑
Fingers crossed! I'm hoping for one of your usually detailed posts --but in the photo section, after the meet! 😁
Absoultely, Ernie. I'll take lots of pics.