Yarisworld Archive

2007 Alternator in a 2012

10 posts · 6,506 views

Frank NecrosisOriginal postYoungstown, Oh · May 30, 2019#1
Will an alternator from a 2007 drop into a 2012?

Replies 9

Frank NecrosisThread starterYoungstown, Oh · Jun 5, 2019#2
Doing some research on this and still coming up with nothing definitive.

The part number for the 2007 alternator is 27060 21150. This part number was superseded around 2009 by 27060 21151.

I am going to drop in the 2007 alternator in my 2012 and see what happens.
seatech30California · Jun 7, 2019#3
Originally Posted by Frank Necrosis ↑
Doing some research on this and still coming up with nothing definitive.

The part number for the 2007 alternator is 27060 21150. This part number was superseded around 2009 by 27060 21151.

I am going to drop in the 2007 alternator in my 2012 and see what happens.
I checked both parts in Toyotapartsdeal, and the 2012 part number shows as compatible with my 2008 yaris, so perhaps it is? They show 12V 80A spec on both. I would imagine you might just run into different connections. I can send you a pick of my alternator if that helps.
Frank NecrosisThread starterYoungstown, Oh · Jun 10, 2019#4
The connections are the same. The 2007 alternator plugs right in.
Jason@SportsCarDebary, FL · Jun 10, 2019#5
The pulley changed at some point, but I don't recall if it was with the bodywork in 2012 or if it happened later. I have interchanged the two, just swapped the pulley - it is visibly different, you can't miss it.
Frank NecrosisThread starterYoungstown, Oh · Jun 11, 2019#6
Originally Posted by Jason@SportsCar ↑
The pulley changed at some point, but I don't recall if it was with the bodywork in 2012 or if it happened later. I have interchanged the two, just swapped the pulley - it is visibly different, you can't miss it.
Thanks for the info. I will check the pulley.

There are two different length belts available for the 2012. The pulley on the alternator may be the difference.
tmontagueCaledonia Ont. · Jun 11, 2019#7
Originally Posted by Frank Necrosis ↑
Thanks for the info. I will check the pulley.

There are two different length belts available for the 2012. The pulley on the alternator may be the difference.
is one for no a/c and the other for the a/c?
Jason@SportsCarDebary, FL · Jun 11, 2019#8
Originally Posted by Frank Necrosis ↑
Thanks for the info. I will check the pulley.

There are two different length belts available for the 2012. The pulley on the alternator may be the difference.
Can't imagine why they would offer two belts. Don't think you could get a non AC Yaris in the U.S.

The pulley change was a shoulder on the backside of the pulley which pushed it out a few mm. Looking at pics I believe this was later than 2012, like 2015ish.

Hard to see here, but in the lower left corner you can see alt pulley with the wider shoulder:
Picture lost · static.cdemo.com

Older Yaris alt pulley:
Picture lost · www.moibbk.com
Frank NecrosisThread starterYoungstown, Oh · Jun 12, 2019#9
Originally Posted by tmontague ↑
is one for no a/c and the other for the a/c?
I don't think it was for an AC delete unless the delete required an idler pulley to replace the AC compressor. Some GM cars have this.

The difference in the belt is about an inch. I always buy both and return the one I don't need.

Thanks for the pics. I really hope I don't have to take the pulley off the 2012. The shaft and nut are a rusted mess.
tmontagueCaledonia Ont. · Jun 12, 2019#10
On older Canadian yaris the diagram without a/c no idler pulley is needed. I have a similar belt set up on my 2zr and when I deleted the a/c no idler pulley was needed.

I guess the only way to know is to find the length difference