Yarisworld Archive

A/C Woes - Opinons/Guidance Welcomed

62 posts · 17,941 views · page 2 of 2

Replies continued

06YarisRSThread starterFredericton, New Brunswick, Canada · Dec 23, 2018#51
Originally Posted by atomic_hoji ↑
Woo! Nice - glad it's worked out for you. Good call by WeeYari.

-- Adam
Yes! I have a new theory, unsupported by EWDs or anything wiring related at this point: The last time I introduced R134, it was cold in the garage. As I mentioned the suction tube became heavily ice encrusted. Maybe the pressure sensor/switch froze up. Tapping it and letting it sit allowed it to open and become operational. So, I'm going with WeeYari's pressure sensor suggestion as being the problem.

Merry Christmas, gentlemen! And, as always, thank you for the invaluable help.
tmontagueCaledonia Ont. · Dec 23, 2018#52
Originally Posted by 06YarisRS ↑
How much does your A/C affect idle on the 2ZR? Mine seemed to labour slightly, until I removed a bit of the refrigerant. It still slows a few rpm when I engage A/C. I'm getting the impression that A/C systems are more power-robbing than I had initially thought.
The engine definitely has a noticeable load difference on it. For a small 4 banger it is quite a bit of draw on its overall power. I know dyno's online have shown anywhere from 3-6hp draw iirc. On a low powered engine this is a large percentage of the overall power output so it is more noticeable.

I'd purge a bit of your r134 out but I dont think you need to release much
06YarisRSThread starterFredericton, New Brunswick, Canada · Dec 23, 2018#53
Originally Posted by tmontague ↑
The engine definitely has a noticeable load difference on it. For a small 4 banger it is quite a bit of draw on its overall power. I know dyno's online have shown anywhere from 3-6hp draw iirc. On a low powered engine this is a large percentage of the overall power output so it is more noticeable.

I'd purge a bit of your r134 out but I dont think you need to release much
Yeah, it's significant. When I removed my manifold gauge high side port today, I noticed a bit of refrigerant bubbling around the bottom of fitting. I think the schrader valve is in a little fitting that may have loosened a bit after opening and closing the ports. I tightened it a bit and the bubbling stopped but the little sight glass seemed to not be full as before. My low side is reading 40, but the system didn't kick in today. I may have lost a little charge but I don't think any air was introduced into the system as it's still under pressure. I'll keep the system in its current state and in the spring, test it. At least I know all the components are functioning properly now - or at least I think they are.
WeeYariGeorgetown, Ontario, Canada · Dec 23, 2018#54
Your pressure sensor may be finding its place onto your shopping list. Mine failed in 2014. I lived without a/c until last year when I finally diagnosed my non-functioning a/c.

Sent from my EML-L09 using Tapatalk
06YarisRSThread starterFredericton, New Brunswick, Canada · Dec 23, 2018#55
Originally Posted by WeeYari ↑
Your pressure sensor may be finding its place onto your shopping list. Mine failed in 2014. I lived without a/c until last year when I finally diagnosed my non-functioning a/c.

Sent from my EML-L09 using Tapatalk
You are probably correct. They look fairly inexpensive, but would necessitate another discharge, vacuum and recharge. I think I'll do this in the spring/summer. I'll probably replace the schrader valves too as well as the o-ring at the firewall (expansion valve?).
06YarisRSThread starterFredericton, New Brunswick, Canada · Dec 23, 2018#56
Originally Posted by WeeYari ↑
Your pressure sensor may be finding its place onto your shopping list. Mine failed in 2014. I lived without a/c until last year when I finally diagnosed my non-functioning a/c.

Sent from my EML-L09 using Tapatalk
Just ordered a Denso on eBay for ~$11.00. Do you happen to know, WeeYari, if the schrader valves are just standard R134 valves and if they are both the same size? Also, I think I'll need a special tool. I have one for tire schrader valves, but it may be different.
WeeYariGeorgetown, Ontario, Canada · Dec 24, 2018#57
Good price on the sensor. New? You wouldn't believe the cost of one through Toyota Canada. North of $600. Why is their price so high? Only available as part of a tubing replacement bundle believe it or not.

As for your Schrader valves, I can't imagine any reason for replacement. They sit there for life under their little protective caps.

Sent from my EML-L09 using Tapatalk
06YarisRSThread starterFredericton, New Brunswick, Canada · Dec 24, 2018#58
Originally Posted by WeeYari ↑
Good price on the sensor. New? You wouldn't believe the cost of one through Toyota Canada. North of $600. Why is their price so high? Only available as part of a tubing replacement bundle believe it or not.

As for your Schrader valves, I can't imagine any reason for replacement. They sit there for life under their little protective caps.

Sent from my EML-L09 using Tapatalk
Yes, it's new, unless I'm being scammed. lol.

https://www.ebay.com/itm/For-A-C-Pre...72.m2749.l2649

I think it was mainly leaking around the base of the fitting that holds the schrader valve (turning the manifold gauge dials may have loosened it), though I thought I saw a little bubbling inside the valve toward the base. I gave it a little tap on the top of the schrader valve and it seemed to seat and there were no more bubbles. They may be fine, but I thought since I have to discharge the system again to replace the sensor, I figured I'd do the schrader valves at the same time.
WeeYariGeorgetown, Ontario, Canada · Dec 24, 2018#59
I went with a somewhat more expensive listing. Can't remember why but I suspect it was because shipping on the cheaper ones was stupid high.

Sent from my EML-L09 using Tapatalk
dogsridewithUSAnotCA · Dec 24, 2018#60
often find valve cores loose in schrader stems
06YarisRSThread starterFredericton, New Brunswick, Canada · Dec 24, 2018#61
Originally Posted by dogsridewith ↑
often find valve cores loose in schrader stems
Thanks. I am going to pick up an A/C schrader valve tool as well. May try just snugging them up a bit.
06YarisRSThread starterFredericton, New Brunswick, Canada · Dec 27, 2018#62
Our local APM auto parts store actually had an A/C schrader valve tool - and this after calling half a dozen shops in the city 80 kms away and no one having one. $6.00 + tax out the door. I'm heading across the border tomorrow to pick up my Denso sensor, 2 cans R134 and the schrader kit.

Current plan is to wait for a warmish day, get my garage up to 65 - 70F, aim my big fan at the condensor and try again. I'll evacuate, replace the o-ring at the expansion valve, the schrader valves and pressure sensor. Then, a lengthy vacuum test. Finally a recharge quantity of R134 (~ 13 oz) and pressure tests based on ambient temps.

From both what Trevor said and what I've read, this is work best not done in winter. I wonder if my vacuum tube would have iced up so badly in warmer weather.