Lol I’m guessing it was anything. I was able to use it on the sway bar and a main breaker for my house.
2012 L with SE front, SC and other racing goodies
75 posts · 24,226 views · page 2 of 2
Replies continued
did you also buy a #1 dad mug and condoms? 🙄Originally Posted by Dliverance ↑Lol I’m guessing it was anything. I was able to use it on the sway bar and a main breaker for my house.
Got my Megan acleback on today. I was expecting more sound but I can hardly hear it over the loud federals. Did pretty good at today’s event though. I’m hoping the sway bar will be here this week so I can have it installed for the next event.
Picture not included in this copy
Picture not included in this copy
I also need to lower the rear. That’s as low as it goes in that picture. I need to remove the adjustable perches to go lower.
So the supercharger kit is for a 2ng gen and I didn’t realize the ecu’s were different between the 2nd and third gen. The piggyback needs tapped into the tach, maf, o2 sensor, and power. I was able to figure out all of the 2nd gen wiring but I can’t find a pinout for a 2012 ecu anywhere.
The previous owner also said that power enterprise told him to leave out the wire for the o2 to get rid of the check engine light that he was having. This seems odd to me. The controller tricks the maf and has a vacuum line hooked up to see how much boost it’s making but it doesn’t seem right to not have the controller hooked up to the o2.
I’m going to keep looking for a 2012 ecu pinout and try to get in touch with power enterprise tomorrow. I don’t feel right without the controller knowing if it’s adding the right amount of fuel.
The previous owner also said that power enterprise told him to leave out the wire for the o2 to get rid of the check engine light that he was having. This seems odd to me. The controller tricks the maf and has a vacuum line hooked up to see how much boost it’s making but it doesn’t seem right to not have the controller hooked up to the o2.
I’m going to keep looking for a 2012 ecu pinout and try to get in touch with power enterprise tomorrow. I don’t feel right without the controller knowing if it’s adding the right amount of fuel.
I have a pinout somewhere 😎Originally Posted by Dliverance ↑So the supercharger kit is for a 2ng gen and I didn’t realize the ecu’s were different between the 2nd and third gen. The piggyback needs tapped into the tach, maf, o2 sensor, and power. I was able to figure out all of the 2nd gen wiring but I can’t find a pinout for a 2012 ecu anywhere.
The previous owner also said that power enterprise told him to leave out the wire for the o2 to get rid of the check engine light that he was having. This seems odd to me. The controller tricks the maf and has a vacuum line hooked up to see how much boost it’s making but it doesn’t seem right to not have the controller hooked up to the o2.
I’m going to keep looking for a 2012 ecu pinout and try to get in touch with power enterprise tomorrow. I don’t feel right without the controller knowing if it’s adding the right amount of fuel.
You should find it and share the wealthOriginally Posted by DarkShadowFox ↑I have a pinout somewhere 😎
I got sent an email off to power enterprise. They have a kit specific to the 3rd gen and it uses the same controller so that’s good. I asked them for the installation manual for my year. Hopefully they get that sent off soon. I really want to get the kit installed before the next event.
what does a pinout diagram look like i have a shit ton of options on my GSIC:Originally Posted by Dliverance ↑You should find it and share the wealth
Picture not included in this copy
okay i have two diagrams for 'ECM' let me know if these help:
Picture not included in this copy
Picture not included in this copy
Picture not included in this copy
Picture not included in this copy
I need this one ^ but for the 2012 connector with descriptions
it is for the 2012. the 2012 is the 2011 in europe. and so on and so forth.Originally Posted by Dliverance ↑I need this one ^ but for the 2012 connector with descriptions
Picture not included in this copy
Looks a little different to me
Looks a little different to me
i dunno dude your gonna have to wire trace your harness or find a more updated version.Originally Posted by Dliverance ↑Picture not included in this copy
Looks a little different to me
Thank you for the effort though
It’s been a long few days of dealing with this piggyback. I finally got an email back from power enterprise and they were super helpful. They sent me the wiring diagram for the ncp131 but unfortunately, they use a newer controller. The new controller from them would have cost me about $1200 shipped but while I was looking, I found the mapecu3 looks remarkably similar to the power enterprise pmap controller. The connectors and wire colors are all the same. After learning this, I started looking for mapecu controllers. The mapecu3 (newest model with features I don’t need) costs about $650 new but I was able to find the mapecu gen 1 for $200. The only problem now is that the map ecu 1 has one 18 pin connector and the 3 has an 18 and a 16. Right now I’m waiting for an email back from mapecu to get a copy of the diagram for the gen 3. Once I get that, the only thing I need is the map for the ncp131 from power enterprise.
It sounds like a complicated cluster f but it’s really not that bad. Best part is that I’ll be able to sell the 07-11 piggyback to recoup some funds for the mapecu purchase.
It sounds like a complicated cluster f but it’s really not that bad. Best part is that I’ll be able to sell the 07-11 piggyback to recoup some funds for the mapecu purchase.
I was able to find the pinout for the newer mapecu. I need the 2 or 3 to run the supercharger. The gen 1 doesn’t have ignition timing capabilities. I was able to find the pinout and identify the wires on the ecu side too. The good news is that power enterprise got ahold of me and let me know that it’s the same programmer and their map will work. I’m just trying to source a gen 2 now. I’m pretty stoked.
Awesome score! I saw the box shape and then I saw the part number. I thought, hey! I know what that is! I am installing mine in the next few days. 👍🏽Originally Posted by Dliverance ↑
Haha awesome. I’ve been procrastinating on installing mine.
Here’s the mapecu2 I found. $300 on Facebook.
Picture not included in this copy
Here’s the mapecu2 I found. $300 on Facebook.
Picture not included in this copy
Woohoo!!! Just paid for the map. I can start the installation when I get back from my trip to Florida.
Originally Posted by Dliverance ↑Got my Megan acleback on today. I was expecting more sound but I can hardly hear it over the loud federals. Did pretty good at today’s event though. I’m hoping the sway bar will be here this week so I can have it installed for the next event.
Picture not included in this copy
will that exhaust fit a 2014 2 door hatch?
If it fits on a 2012 it will fit on a 2014.
Originally Posted by Dliverance ↑Hi gang. I made the upgrade to a 2012 from my 2008. I’ll be putting all of my other oarts on the new car. For those of you who haven’t seen my other thread, I have some BC racing coilovers, a Recaro seat, Sparco wheel, some volk TE37V’s and a power enterprise supercharger that will be going on the new car.
I will also be swapping the front end of the ‘12 to an SE front end. I think I’ll have the only two door SE car :). So far I’ve ordered everything I need and I’m just waiting for parts to show up. Hopefully the bumper reinforcement and headlights are the same. Here’s an almost complete list of the parts I’m using. The only part that I ordered that’s not on this list is the chrome surround piece for the lower dam. I ordered that the next day.
I can list the part numbers individually if someone else wants them. All in it cost me about $380 for the parts. Fog lights not included since I already had them from my other car.
Picture not included in this copy
Picture not included in this copy
what website did you buy your parts from?
Looks terrific, good job !