Yarisworld Archive

n00b suspension install question

25 posts · 17,898 views

The StigOriginal postNor Cal · Jun 11, 2007#1
If I'm going to install Tein S Springs + TRD Shocks, do I need (aside from tools listed in DIY sticky):

1, Spring compressor?
2, Reuse stock bump stop?
3, What else do I need?

Thanks in advance guys!

Replies 24

nqdBoston, MA · Jun 11, 2007#2
i installed my s techs with the same bump stops but i used the stock shocks.... and yes you will need a spring compressor for the stock spring... i bought a set from my local automotive store and returned it the next day....


and third some beers and a nice sunny day
joey1320Lakewood, Ohio · Jun 11, 2007#3
add a good pizza and some sweaty hot chicks to pass you the tools.

but besides that you will need a spring compressor to switch over the top mount plates. you can either rent them or buy/return it if you don't plan on using it again.
Kaotic LazagnaCentral Valley, CA · Jun 11, 2007#4
when we installed mine (same set up), we didn't need to use spring compressors. and we cut the bump stop like how Chris did.

heh, get ready for a stiff ride (although i wish it is a tad bit stiffer).
The StigThread starterNor Cal · Jun 13, 2007#5
cool, all i need now is about 50 hot chicks to pass me tools 😁

thanks guys!
ROCKLAND TOYOTAROCKLAND COUNTY NY · Jun 13, 2007#6
im also getting ready this saturday to install the same setup. CHRIS or someone else can you tell me how much you cut your bumpstops and do i really need to if i use the stock struts.....
ToyotechOak Ridge, NJ · Jun 13, 2007#7
Originally Posted by ROCKLAND TOYOTA ↑
im also getting ready this saturday to install the same setup. CHRIS or someone else can you tell me how much you cut your bumpstops and do i really need to if i use the stock struts.....
normally cut about 2 ribs off
death is my giftdallas · Jun 13, 2007#8
stupid boys with your tools.
i STILL haven't gotten my Yari lowered.
good luck Stig
kurokoma-kunmy own little world · Jun 13, 2007#9
Originally Posted by death is my gift ↑
stupid boys with your tools.
i STILL haven't gotten my Yari lowered.
good luck Stig
Maybe he will do it for you if you pass him the tools? 😆

Seriously I have a question about the spring compressor... is it completely safe to use at home? Something about handling the spring while its tensioned freaks me out...
ROCKLAND TOYOTAROCKLAND COUNTY NY · Jun 13, 2007#10
Originally Posted by Toyotech ↑
normally cut about 2 ribs off
THIS IS GOOD FOR BOTH THE TRD AND STOCK STRUTS????
The StigThread starterNor Cal · Jun 13, 2007#11
Originally Posted by kurokoma-kun ↑
Maybe he will do it for you if you pass him the tools? 😆

Seriously I have a question about the spring compressor... is it completely safe to use at home? Something about handling the spring while its tensioned freaks me out...
yeah i'm kind of paranoid about the compressor too, but i guess it's ok....it ain't my garage LOL...

death: i'm mechanically challenged...however, i got some mad lego skillz...reading a couple of DIYs got me think that this is just a full size lego set....yeah, i need lots of luck here 😆
churpTropical Minnesota · Jun 13, 2007#12
Originally Posted by ROCKLAND TOYOTA ↑
THIS IS GOOD FOR BOTH THE TRD AND STOCK STRUTS????
Myself I wouldn't cut them for the stock struts...they are designed to keep the strut cylinder from bottoming out. The bump stop bottoming is much softer and less damaging that having the cylinder bottom out. Aftermarket struts are probably different, but I can't imagine any car manufacturer engineering their products with more clearance than needed....it usually costs money!

Has anyone actually checked how far down the strut can go, with and without the bump stops....would be easy to do with the spring off. Then you could tell how much distance the bump stop has to compress before the cylinder bottoms. Of course then you'd have to decide how much you think the bump stop would compress under a severe load. No matter what...the longer the bump stop is the softer the 'thump' will be when it hits.
slothman86Savannah, GA · Jun 13, 2007#13
or some huge guy named Hans to compress the spring for you
JerkrattFair Lawn, NJ · Jul 11, 2007#14
my friend put spings in his mazda prog... and they used 4 ppl holding the spring down lol in his front lawn
slvryarisIndiana · Jul 11, 2007#15
Usually however far you drop it say its an inch then you cut an inch off the bump stop. I believe that is the rule of thumb. Double check Chris's DIY for sure.
MrJesterHomo · Jul 11, 2007#16
I cut ribs down on the bump stop don't notice much rub at all. There a couple pot holes on my way to work that will bottom me out but they are quite large so I just do my best avoid them. :)
nqdBoston, MA · Jul 11, 2007#17
yes i beleive its the same set up as the xb
Kaotic LazagnaCentral Valley, CA · Jul 11, 2007#18
i didn't need a spring compressor when we installed my S.Tech's.
nqdBoston, MA · Jul 11, 2007#19
Originally Posted by Kaotic Lazagna ↑
i didn't need a spring compressor when we installed my S.Tech's.
yea smae here but i DID need them to take off the stock springs
MrJesterHomo · Jul 11, 2007#20
Yeah taking the stock ones out you will need a compressor but for install you do not need a compressor.
brickhardmeatInner City, Dallas · Jul 11, 2007#21
installed my basics this past weekend no compressor for the rear and didn't even take the wheels off the rear, front needed compressor to get to parts, cut bump stops and cut dust covers front and rear
Chris07LBNew Jersey · Jul 11, 2007#22
Re-read my DIY.

Removing stock springs from stock struts - Use a spring compressor.. let's be safe here.

Installing new Tanabe's to stock struts - No spring compressor needed.

Look at the side by side pictures of the stock .vs. tanabe spring, and you will see why. 🙄

Also, for those that wish to follow Tanabe's instructions, cutting the bump stop is also shown in my pictures... and how much to (which part) to reuse.

Just a reminder, this DIY was done using Tanabe DF's with stock struts and shocks.. using other springs and or struts and shocks, may require different measurements for cutting, or no cutting at all of your bump stops.

... back to dinner.
brickhardmeatInner City, Dallas · Jul 11, 2007#23
Originally Posted by Chris07LB ↑
Re-read my DIY.



... back to dinner.
um....tacos?
Chris07LBNew Jersey · Jul 11, 2007#24
nope, better. 🙂