zeroslOriginal postNY · Oct 17, 2017#1So I have an 08 but can't figure out where to start with this exhaust leak.
It is likely near the exhaust headers or downpipe as exhaust smell comes into the cabin if i have my HVAC to vent from outside.
Any suggestions for techniques or places to start looking?
Thanks
Replies 28
WeeYariGeorgetown, Ontario, Canada · Oct 17, 2017#2With 99% certainty, it is the donut gasket between the header and the down pipe. An '08 is past due for replacement if still on the original Open the hood, start the car, and reach into that area with an open hand. You should be able to feel the gases puffing against your fingers.
This is what the gasket in my '06 looked like in November 2011. I am once again due for a replacement.
Picture lost · uploads.tapatalk-cdn.com
Sent from my Elite_5_5_Octa using Tapatalk
06YarisRSFredericton, New Brunswick, Canada · Oct 18, 2017#3^ +1 My money's on WeeYari's diagnosis. Mine was gone, but so was the entire flange. The cat pipe had completely separated from the manifold and was hanging down about 1/4".
zeroslThread starterNY · Oct 20, 2017#4do you have any part numbers?
WeeYariGeorgetown, Ontario, Canada · Oct 20, 2017#5Toyota OE part numbers;
Gasket 17451-21070
Bolts 90080-10291
They are not what one would consider cheap.
Sent from my Elite_5_5_Octa using Tapatalk
06YarisRSFredericton, New Brunswick, Canada · Oct 20, 2017#6govtecPhila, PA · Oct 21, 2017#7How hard is this job to do it myself and what are the steps involved to change out the gaskets and bolts? Thanks
IllusionXBrossard, QC · Oct 21, 2017#8 Originally Posted by
govtec ↑ How hard is this job to do it myself and what are the steps involved to change out the gaskets and bolts? Thanks
If you live in salt belt. The bolt is likely rusted, and you will need to heat the bolt till red to take it out. It's not a job to crawl under to do.
Sent from my SM-G930W8 using Tapatalk
govtecPhila, PA · Oct 21, 2017#9Ok, I might just take it to Midas.
06YarisRSFredericton, New Brunswick, Canada · Oct 21, 2017#10 Originally Posted by
govtec ↑ Ok, I might just take it to Midas.
That's probably the best thing to do because they do tend to rust badly with moisture and continual heating/cooling cycles. That said I have removed pretty rusty ones by soaking them a few times with ReleasAll or similar and used my electric impact gun. I can't see a muffler shop charging much at all to replace that donut.
IllusionXBrossard, QC · Oct 21, 2017#11 Originally Posted by
06YarisRS ↑ That's probably the best thing to do because they do tend to rust badly with moisture and continual heating/cooling cycles. That said I have removed pretty rusty ones by soaking them a few times with ReleasAll or similar and used my electric impact gun. I can't see a muffler shop charging much at all to replace that donut.
It was a good 20mins job.
Sent from my SM-G930W8 using Tapatalk
zeroslThread starterNY · Oct 23, 2017#12Ordered the parts from RockAuto
Order Parts List:
EASTERN EXHAUST EE4979 Springs
EASTERN EXHAUST EE4978 Bolts
FEL-PRO 61502 {#1745121070} Flange Donut Gasket
Parts should arrive friday and will tackle on saturday
I have access to a four post lift and will hopefully will tackle this quickly
xdarkxfirexhamilton, on · Oct 23, 2017#13I had the same problem, no leak, but a noise and couldnt figure out where it was coming from. Turned out to be this flange gasket. Toyota wanted almost $50 for it and I got it from a local parts shop aftermarket for $8. Had to sand it a little to get a perfect fit. After that it was fine. Reused same bolts and put antiseize on threads.
zeroslThread starterNY · Oct 28, 2017#14well, I started on this job and the bolts were so corroded that they both snapped.
I may well call it a day
zeroslThread starterNY · Oct 28, 2017#15I was able to cut away the bolts between the flanges, but will need a longer drill. I replaced the donut gasket and clamped it shut with a U bolt until I come back to it after purchasing the correct parts
Noise is gone, but now I have a P0031 fault code.
I wonder if I damaged the O2 sensor while messing around?
nightmare fuel
06YarisRSFredericton, New Brunswick, Canada · Oct 28, 2017#16 Originally Posted by
zerosl ↑
I wonder if I damaged the O2 sensor while messing around?
Maybe the wiring which is not far from the flange. Could you have nicked a wire with your drill bit? The downstream sensor has 4 wires. Not sure about the upstream wideband sensor.
zeroslThread starterNY · Oct 29, 2017#17yea, its possible, I'll start checking the part once I have a free cycle
zeroslThread starterNY · Nov 16, 2017#18zeroslThread starterNY · Nov 27, 2017#19Flange repair was too small, if anyone else decides to go this route, I recommend getting a slightly bigger size
zeroslThread starterNY · Nov 28, 2017#20Walker 31871
or any other flange repair kit that is about 2 1/4 inch
They run about 15 bucks for two from rockauto
Good luck to anyone who needs to do this, hopefully this helps at all
grilled cheeseussnowbirding in Tucson · Mar 25, 2018#21Just replaced the original gasket on my 2007 hatchback with 120k miles and 10 salty upstate NY winters. :D
Photos Before trying to loosen the flange bolts, I used a MAP-Pro torch ($50 at the Homeless Despot) to get the nuts red-hot. You can hit the nuts with a torch from the engine bay -- I unclipped a wiring harness to make more room to work. Watch your aim -- there are O2 sensor wires just above the flange on the driver's side.
After heating each nut, I crawled underneath, hammered a socket with long extension onto the rusty bolt head, and carefully(!) applied torque. Got them both loose with no fuss, and the rest of the job was easy. I used new bolts but kept the original captive nuts.
The replacement gasket I used was a
Walker 31619. May be a little different than OEM gasket size (definitely different material), but it seems to make a good seal. Car sounds
much quieter now and less rough when accelerating. I'm probably breathing cleaner cabin air too.
ezhacker1San Francisco · Mar 26, 2018#22Time to do mine as well. I can taste the fumes with the hood open.. and a shot of SeaFoam shows it's leaking there, also be a good idea to take the header off and check that as well. Good info on the or replacements.
zeroslThread starterNY · Mar 26, 2018#23Yes, I would definitely monitor this in the future and for anyone else who owns this vehicle.
My spring bolts were just corroded to pieces which is why they snapped so quickly.
But yes, Definitely torch/Heat before torquing anything exhaust in the future!
hodginsaBrantford, Ontario · Dec 4, 2018#24I've got to do this soon. Winter is here and heating the car with re-circulation on just fogs the windows bad. Driving with it off the car just fills up with fumes.
Good to know its likely just the gasket. I haven't investigated yet though.
Mike DexterOntario · Dec 7, 2018#25 Originally Posted by
zerosl ↑ I was able to cut away the bolts between the flanges, but will need a longer drill. I replaced the donut gasket and clamped it shut with a U bolt until I come back to it after purchasing the correct parts
Same thing happened to me. I was able to helicoil it by using an adapter to hold the bit/tap/helicoil tool to a 12" extension bar.
myfirstyotaToronto Canada · Dec 7, 2018#26 Originally Posted by
grilled cheeseus ↑
Before trying to loosen the flange bolts, I used a MAP-Pro torch ($50 at the Homeless Despot) to get the nuts red-hot. You can hit the nuts with a torch from the engine bay -- I unclipped a wiring harness to make more room to work. Watch your aim -- there are O2 sensor wires just above the flange on the driver's side.
After heating each nut, I crawled underneath, hammered a socket with long extension onto the rusty bolt head, and carefully(!) applied torque.
Has never failed me. I've done 3 of these gaskets now. Gasket from Toyota (canada) $50-60, I think the bolts are $7 and change each.
dogsridewithUSAnotCA · Dec 7, 2018#27This spring-bolt joint is special. Circa 1990 Corolla and Tercel used a down pipe w/ a flex section, so all stock exhaust connections were flanged. On all of these I used 3/8 stainless nuts and bolts from the hardware store...no more rusty stuck fasteners next time a pipe or muffler was replaced.
DarkShadowFoxMassachusetts · Dec 7, 2018#28flex seal
dogsridewithUSAnotCA · Dec 8, 2018#29Isn't "flex seal" polyurethane glue and caulk sold on TV? (Guy cuts a boat in half, glues it together and zooms across the lake.)