Yarisworld Archive

Cold air intake?

73 posts · 54,931 views · page 1 of 2

Yaris709Original postNewfoundland · Apr 10, 2017#1
Anyone on here running a cold air intake? Wondering if it's worth the money on the yaris or just a waste

Replies 72

Bluevitz-rsOshawa, Ontario, Canada · Apr 10, 2017#2
It makes a difference. But it also makes for some better induction noise.
invader166Langley, BC · Apr 10, 2017#3
Unless you plan on doing the wholle induction system (intake, throttle, and manifold) than I it's kind of a waste.

Unless of course you want extra induction noise with no real extra power. 😆
tarkusYYZ · Apr 10, 2017#4
The Yaris' stock intake is already placed to take in cooler air. So that's not really an issue. On my Yaris, I've just put in a drop-in replacement AfE filter, which provides higher airflow and is also washable. Then I removed the carbon filter from the air box as well. It gives the car a little more go, and a bit more growl.

Sent from my phone with Tapatalk. Please excuse any typpos.
rabbitoThailand · Apr 13, 2017#5
just like tarkus said..stock box is already cool enough...go with throttle body or manifold...had the intake but took them off, no real gain...i went with 1zz throttle body with custom piping thay matches the exact size of t.b and intake box

Sent from my SM-N920C using Tapatalk
CrankyOldManWest Michigan · Apr 13, 2017#6
It's absolutely hilarious on a supercharged 1NZ with a 1ZZ throttle body. Lots of loud supercharger noises and some serious HP gains to boot. On an otherwise stock engine, you may see a few HP gained.
ecamposCosta Rica · Apr 26, 2017#7
I have a cold air intake on my Yaris, I think it mostly just adds kind of a growl throttle noise. Performance gains are minimal if any.

If you want to get a mod and actually feel a slight difference go with exhaust headers, you'll feel that more than the CAI.
ncp13Athens Greece · Apr 27, 2017#8
Anyone has dynoed before and after?
I also love a good intake growl but with added benefits :)
SirDigbyDenver, Colorado · Apr 27, 2017#9
Originally Posted by vitz rs gs ↑
I don't have a dyno test but I have tested on the same road my accelaration from 0 to 100 km/h. Before 12 sec after its aprox 10 sec
you shaved 2 seconds off 0-62mph with an intake and a muffler? that's the most amazing thing i've heard this week! i've seen people pay $5,000 to accomplish this, who knew all they needed was an intake and a muffler....
tmontagueCaledonia Ont. · Apr 28, 2017#10
I don't even think my 2zr swap netted me 2 seconds....
ncp13Athens Greece · Apr 28, 2017#11
You better check your timing device :) 2 sec sounds very optimistic !
miisergreece · Apr 28, 2017#12
Originally Posted by SirDigby ↑
you shaved 2 seconds off 0-62mph with an intake and a muffler? that's the most amazing thing i've heard this week! i've seen people pay $5,000 to accomplish this, who knew all they needed was an intake and a muffler....


I saw the comment yesterday and I had write like 100 lines of response but then I said nahhh let it be :p


Sent from my iPhone using Tapatalk
miisergreece · Apr 28, 2017#13
Originally Posted by miiser ↑
I saw the comment yesterday and I had write like 100 lines of response but then I said nahhh let it be :p

It's the feeling when someone spent like 320$ on a filter and he is trying to convince himself that he did a good choice :p

I mean common 300$ for a filter? I searched it on amazon yesterday and that's the price.
Really with this amount of money you can do so maaaany better things:
•put a spoiler
•put a good sound system with touchscreen and amp + new speakers
•convert the cloth seats to leather by a professional workshop
And much more things
They don't change the power, but neither the filter does

Sent from my iPhone using Tapatalk





Sent from my iPhone using Tapatalk
thebarberGrand Rapids, MI · Apr 28, 2017#14
its worth it especially if you plan on some day getting a header and full exhaust (not just a muffler section)
Yaris709Thread starterNewfoundland · Apr 28, 2017#15
Will probably go with an intake soon and sometime in the future maybe a header will be installed. Probably wait for the manifold to leak and replace it with a header then
SirDigbyDenver, Colorado · Apr 28, 2017#16
sound system and leather adds weight=slows vehicle down.
spoiler adds drag=slows vehicle down
i have an injen intake. i think it was $130
injen flow tunes intake tube=speeds vehicle up (maybe .2 second faster 0-62)
k&n flow tune (???)
tarkusYYZ · Apr 28, 2017#17
Originally Posted by Yaris709 ↑
Will probably go with an intake soon and sometime in the future maybe a header will be installed. Probably wait for the manifold to leak and replace it with a header then
Install a 1zz (Corolla/ Matrix) throttle body to really open up the performance.

Sent from my phone. Please excuse any typpos.
rabbitoThailand · Apr 29, 2017#18
Originally Posted by tarkus ↑
Install a 1zz (Corolla/ Matrix) throttle body to really open up the performance.

Sent from my phone. Please excuse any typpos.
not just opens up the performance...it really kick in :)

Sent from my SM-N920C using Tapatalk
miisergreece · Apr 29, 2017#19
Originally Posted by SirDigby ↑
sound system and leather adds weight=slows vehicle down.
spoiler adds drag=slows vehicle down
i have an injen intake. i think it was $130
injen flow tunes intake tube=speeds vehicle up (maybe .2 second faster 0-62)
k&n flow tune (???)


Wait you really think that a sound system will slow down your car?? Picture not included in this copy about 0.001 sec?
As I said they don't give any speed upgrade but neither filter gives any speed bump.

Sent from my iPhone using Tapatalk
thebarberGrand Rapids, MI · Apr 30, 2017#20
Originally Posted by Yaris709 ↑
Will probably go with an intake soon and sometime in the future maybe a header will be installed. Probably wait for the manifold to leak and replace it with a header then
Won't happen
SirDigbyDenver, Colorado · May 5, 2017#21
sorry. when i think "sound system" i think lots of heavy gauge wire, amplifiers, subs, etc. i forgot we were talking $300...
NJP440Ohio · Jun 15, 2017#22
Ok time for me to jack this thread. I ordered an intake for my 2010 yaris 3dr and the air sensor does not bolt up at all! Very far off on the bolt holes. Yes I bought a cheap intake but for those who are on the facebook page and remember Aimee and her 3rd gen "laboon" she had the same problem with her AFE intake. Now we are talking $50 intake vs a $300 intake so I can't call quality here, there must be something else at play. Anyone run into this issue? Does our car have 2 different model air sensors?
Pic of my cheap intake for hilarity purposesPicture not included in this copy

Sent from my LG-H918 using Tapatalk
ecamposCosta Rica · Jun 15, 2017#23
Originally Posted by NJP440 ↑
Ok time for me to jack this thread. I ordered an intake for my 2010 yaris 3dr and the air sensor does not bolt up at all! Very far off on the bolt holes. Yes I bought a cheap intake but for those who are on the facebook page and remember Aimee and her 3rd gen "laboon" she had the same problem with her AFE intake. Now we are talking $50 intake vs a $300 intake so I can't call quality here, there must be something else at play. Anyone run into this issue? Does our car have 2 different model air sensors?
Pic of my cheap intake for hilarity purposesPicture not included in this copy

Sent from my LG-H918 using Tapatalk
I ran into the same issue and had to do this:

Picture not included in this copy

Basically modify the stock depurator cap, cut the intake, fit it with couplings. No issues so far.
NJP440Ohio · Jun 15, 2017#24
Originally Posted by ecampos ↑
I ran into the same issue and had to do this:

Picture not included in this copy

Basically modify the stock depurator cap, cut the intake, fit it with couplings. No issues so far.
I'm trying so hard not to cut up my stock parts 😭

Sent from my LG-H918 using Tapatalk
ecamposCosta Rica · Jun 15, 2017#25
Originally Posted by NJP440 ↑
I'm trying so hard not to cut up my stock parts 😭

Sent from my LG-H918 using Tapatalk
Oh I didn't... I put away the stock piece and ordered a new one to experiment, it was like $30 xD
NJP440Ohio · Jun 15, 2017#26
Originally Posted by ecampos ↑
Oh I didn't... I put away the stock piece and ordered a new one to experiment, it was like $30 xD
Ohhh ok ill take a look on eBay see if anything pops up

Sent from my LG-H918 using Tapatalk
ecamposCosta Rica · Jun 15, 2017#27
Originally Posted by NJP440 ↑
Ohhh ok ill take a look on eBay see if anything pops up

Sent from my LG-H918 using Tapatalk
So the part number for your car I think is: 17705-21100 CAP SUB-ASSY, AIR CLEANER

Found this on eBay: http://www.ebay.com/itm/2006-11-TOYO...1RP7ry&vxp=mtr
NJP440Ohio · Jun 15, 2017#28
Originally Posted by ecampos ↑
So the part number for your car I think is: 17705-21100 CAP SUB-ASSY, AIR CLEANER

Found this on eBay: http://www.ebay.com/itm/2006-11-TOYO...1RP7ry&vxp=mtr
Oh boy I'm def not a fan of trying to make that work 😂 ill be searching other options

Sent from my LG-H918 using Tapatalk
SirDigbyDenver, Colorado · Jun 15, 2017#29
your options are; cut up stock box and aftermarket tubing and use 3 couplers and filter. buy another intake. use aftermarket tubing with stock air box. use stock tubing and stock air box.
NJP440Ohio · Jun 15, 2017#30
Originally Posted by SirDigby ↑
your options are; cut up stock box and aftermarket tubing and use 3 couplers and filter. buy another intake. use aftermarket tubing with stock air box. use stock tubing and stock air box.
So no matter what you're 50/50 odds with ordering an intake?

Sent from my LG-H918 using Tapatalk
alias06MN · Jun 16, 2017#31
Originally Posted by vitz rs gs ↑
I don't have a dyno test but I have tested on the same road my accelaration from 0 to 100 km/h. Before 12 sec after its aprox 10 sec


Sent from my iPhone using Tapatalk
Stock 0-60 time is in the 10 sec range. I seriously doubt that an intake did anything.
DiCaprioGermany · Jun 16, 2017#32
Originally Posted by alias06 ↑
Stock 0-60 time is in the 10 sec range. I seriously doubt that an intake did anything.
It all comes down to the launch and conditions.
I've done a before and after test with new tires, lightweight alloys and air intake.
The car was stock before.

Before with winter tires and stock air intake the best i could do was 11.1 sec
After with new sticky summer tires and aftermarket air intake the best i could do was 11.3 sec.

So after i did the mods my 0-62 times were worse than before.
So i guess my winter tires stick well enough to put the power down and it all comes down to the launch and your shifting.
You can scrape off some time with good shifting.

But with a bad launch my times are always in the 12-13 sec range.

My engine is the 1.3l 2SZ-FE
Bluevitz-rsOshawa, Ontario, Canada · Jun 16, 2017#33
Originally Posted by NJP440 ↑
Ok time for me to jack this thread. I ordered an intake for my 2010 yaris 3dr and the air sensor does not bolt up at all! Very far off on the bolt holes. Yes I bought a cheap intake but for those who are on the facebook page and remember Aimee and her 3rd gen "laboon" she had the same problem with her AFE intake. Now we are talking $50 intake vs a $300 intake so I can't call quality here, there must be something else at play. Anyone run into this issue? Does our car have 2 different model air sensors?
Pic of my cheap intake for hilarity purposesPicture not included in this copy

Sent from my LG-H918 using Tapatalk
I know it seems simple to me, but are you sure you were mounting the MAF in the correct direction. It only goes in one way because the holes are offset.
NJP440Ohio · Jun 16, 2017#34
Originally Posted by Bluevitz-rs ↑
I know it seems simple to me, but are you sure you were mounting the MAF in the correct direction. It only goes in one way because the holes are offset.
110% sure. There's a 4mm difference in mounting hole spacing and even the hole for the sensor to go in is 1mm too small

Sent from my LG-H918 using Tapatalk
Bluevitz-rsOshawa, Ontario, Canada · Jun 16, 2017#35
^^ok just making sure. That really sucks though.
alias06MN · Jun 19, 2017#36
Originally Posted by DiCaprio ↑
It all comes down to the launch and conditions.
I've done a before and after test with new tires, lightweight alloys and air intake.
The car was stock before.

Before with winter tires and stock air intake the best i could do was 11.1 sec
After with new sticky summer tires and aftermarket air intake the best i could do was 11.3 sec.

So after i did the mods my 0-62 times were worse than before.
So i guess my winter tires stick well enough to put the power down and it all comes down to the launch and your shifting.
You can scrape off some time with good shifting.

But with a bad launch my times are always in the 12-13 sec range.

My engine is the 1.3l 2SZ-FE

The biggest difference that comes into play between your time and mine is that our engines are different. I have the 1NZ, and even with a wheel/tire setup that is heavier than stock and an axleback I've been able to get a 10 second range 0-60 with everything stock otherwise.

Sticky tires can take away performance of a car also. They have a higher rolling resistance, which basically means that you need more energy to move them than a tire with lower rolling resistance tires such as snow tires or energy conserving tires. With the 2SZ being limited on power already as is, sticky tires can negatively impact the performance.

Honestly, just by adding an intake and exhaust isn't going to make any car much faster (there are exceptions). It will however make your car louder, and if that is what floats your boat then 👍
Yaris709Thread starterNewfoundland · Jun 20, 2017#37
Originally Posted by NJP440 ↑
Ok time for me to jack this thread. I ordered an intake for my 2010 yaris 3dr and the air sensor does not bolt up at all! Very far off on the bolt holes. Yes I bought a cheap intake but for those who are on the facebook page and remember Aimee and her 3rd gen "laboon" she had the same problem with her AFE intake. Now we are talking $50 intake vs a $300 intake so I can't call quality here, there must be something else at play. Anyone run into this issue? Does our car have 2 different model air sensors?
Pic of my cheap intake for hilarity purposesPicture not included in this copy

Sent from my LG-H918 using Tapatalk
I have the exact same issue with an intake I ordered. It sucks haha and I can't return it now cause I had it forgot about. Have to find a way to rig it up to work somehow. I could file out the maf sensor hole and try to find a way to secure the sensor down tight. The maf sensor is literally less than a mm to big but screw holes are off quote a bit.
Yaris709Thread starterNewfoundland · Jun 26, 2017#38
Bump if anyone could point me in the right direction to get my intake to work
heeroyuy01195Florida · Jun 27, 2017#39
If the screw holes are that far off it might be better to drill new holes and tap them if there's enough material. If not then I would say try and find a different intake or at least a section with a MAF mount. I think someone had one posted in the classifieds section on the forum. Can you put up a picture or two of the hole alignment?
Bluevitz-rsOshawa, Ontario, Canada · Jun 27, 2017#40
Does the sensor fit in the hole? The screws aren't esencial, they're just there to locate its orientation and keep it in place.
NJP440Ohio · Jun 27, 2017#41
Originally Posted by Bluevitz-rs ↑
Does the sensor fit in the hole? The screws aren't esencial, they're just there to locate its orientation and keep it in place.
Sensor is maybe 1mm bigger than the hole

Sent from my LG-H918 using Tapatalk
Bluevitz-rsOshawa, Ontario, Canada · Jun 27, 2017#42
Well if you have tools to make the hole bigger and get the sensor in there you can just seal it with a little silicone and zip ties.
NJP440Ohio · Jun 27, 2017#43
Originally Posted by Bluevitz-rs ↑
Well if you have tools to make the hole bigger and get the sensor in there you can just seal it with a little silicone and zip ties.
That works

Ill post updates

Sent from my LG-H918 using Tapatalk
Bluevitz-rsOshawa, Ontario, Canada · Jun 27, 2017#44
Just make sure it's oriented in the right direction and dead nuts straight.
NJP440Ohio · Jun 27, 2017#45
Originally Posted by Bluevitz-rs ↑
Just make sure it's oriented in the right direction and dead nuts straight.
I think I can bolt one bolt in? I don't remember honestly. When I saw it didn't work I ripped out the intake pipe and chucked it across the drive lmao. I'm off this weekend ill try it then

Sent from my LG-H918 using Tapatalk
Yaris709Thread starterNewfoundland · Jun 27, 2017#46
Never thought about zip tying the sensor down. That'll work! I'm guessing if I take a metal file to the hole ill be able to get it to fit. It's not off by much but enough to piss me off hahaha
NJP440Ohio · Jun 27, 2017#47
Originally Posted by Yaris709 ↑
Never thought about zip tying the sensor down. That'll work! I'm guessing if I take a metal file to the hole ill be able to get it to fit. It's not off by much but enough to piss me off hahaha
Does one bolt hole line up? I can't remember at all I was in rage lol

Sent from my LG-H918 using Tapatalk
Yaris709Thread starterNewfoundland · Jun 27, 2017#48
Nope neither lined up on mine. Both were off about 3-5 mm or so. The maf is less than a mm from fitting but it wouldn't go down. I'd say I'll be installing it this weekend coming & I'll let you know how it works out
NJP440Ohio · Jun 27, 2017#49
Originally Posted by Yaris709 ↑
Nope neither lined up on mine. Both were off about 3-5 mm or so. The maf is less than a mm from fitting but it wouldn't go down. I'd say I'll be installing it this weekend coming & I'll let you know how it works out
Ill be doing the same haha ill get crafty with some zip ties

Sent from my LG-H918 using Tapatalk
NJP440Ohio · Jul 1, 2017#50
Originally Posted by NJP440 ↑
Ill be doing the same haha ill get crafty with some zip ties

Sent from my LG-H918 using Tapatalk
Well I did it. Bore the MAF hole out 1mm shoved the MAF in and ziptied it on snug. Intake is onPicture not included in this copyPicture not included in this copy

Sent from my LG-H918 using Tapatalk