Yarisworld Archive

JDM Yaris hatchback tail lights + other parts (need help to find them) (2008)

38 posts · 11,407 views

ACKING_QCOriginal postQC, Canada · Nov 22, 2016#1
I'm searching for JDM taillights for my car, i searched pretty much everywhere.. And all I found was a sketchy website that seems to sell replicas at 290$ the piece, not the pair... So I want your help, if you have sources or if you wanna go back stock and get rid of yours, I'll take them... As I want my Yaris to be.. Somewhat ready for next summer. This, plus OEM bmw e30 bottlecap wheels (yeaa bit of a rally theme going on there) aannd the best of all, recaro type r seats...

Replies 37

ACKING_QCThread starterQC, Canada · Nov 22, 2016#3
Lip kits ? ? ? I don't want no lip kits this Yaris will be off road themed (so no drop and bodykit)
ern-dizCA all day · Nov 22, 2016#4
Originally Posted by iceage ↑
...I also have the JDM RS tail lights for sale as well.
🙄

If you weren't able to read and comprehend a very short post (that I found for you in zero seconds after your supposedly extensive prior searching), then I'm not sure what I, or anyone else, can do to help you.
ACKING_QCThread starterQC, Canada · Nov 22, 2016#5
I feel stupid.. only looked up for the links :-/
ern-dizCA all day · Nov 22, 2016#6
No worries, my friend. All good 🙂
SirDigbyDenver, Colorado · Nov 22, 2016#7
JDM OEM and JDM aftermarket:

http://jdmautolights.com/tail-lights...ee1144d830616f

I was patient and I found a set on ebay (JDM OEM) for $150 shipped. it took many months to find this good deal. the listing was up for about an hour before I found it and claimed it!
ACKING_QCThread starterQC, Canada · Nov 22, 2016#8
240$ a pair ? + shipping .. well really around 375 (USD or CAD ???) at that price, and being a college student, I'd rather find some used ones with the correct wiring ...
yarisugiハワイ · Nov 23, 2016#9
Good luck
enviriCT · Nov 23, 2016#10
wire pin wizardry is still needed for 08 i believe.
ACKING_QCThread starterQC, Canada · Nov 23, 2016#11
Originally Posted by enviri ↑
wire pin wizardry is still needed for 08 i believe.
I heard that it is only a jdm connector and a correct rewiring that is neede...I need to find wiring diagram for those that I am 99% sure I can find on there
SirDigbyDenver, Colorado · Nov 23, 2016#12
Originally Posted by ACKING_QC ↑
I heard that it is only a jdm connector and a correct rewiring that is neede...I need to find wiring diagram for those that I am 99% sure I can find on there
you hear wrong. connector is the same as USD/CAD you just re-pin connector. and you're complaining about the price but in your first post you said $290 (CAD?) each, so $580. so this is $200 (CAD) cheaper. if you don't want to spend money for quality, there's always an Auto Zone that can accommodate for your cheap stuff. (BTW, the oem ones are $375 USD. the $240 USD ones are aftermarket)
expect to pay $$$ for most things JDM on Toyota. you get what you pay for. I was prepared to pay $400 USD for these lights, (like $5,000 CAD?) but I took my time and found a great deal...
SirDigbyDenver, Colorado · Nov 23, 2016#13
I've been looking for a RS front bumper and rear bumper. can't find either one less than $850USD, and you have to also buy supports and brackets for RS. USDM bumper is like $150USD...
enviriCT · Nov 23, 2016#14
the pain...I know too well.

1 attachment not included in this copy

ACKING_QCThread starterQC, Canada · Nov 23, 2016#15
Jdm tax... Fckin hate it... But it looks soo good !! :(
enviriCT · Nov 24, 2016#16
Originally Posted by ACKING_QC ↑
Jdm tax... Fckin hate it... But it looks soo good !! :(
Picture not included in this copy
I know, right? #shameless
ACKING_QCThread starterQC, Canada · Nov 24, 2016#17
Anyone here bought the AMBER ones from jdm auto lights???

Is there a difference? And do we still need rewiring ?
SirDigbyDenver, Colorado · Nov 24, 2016#18
most likely will need re-pin on connector.

you posted "+other parts."
any other parts you are having issues locating?
ACKING_QCThread starterQC, Canada · Nov 24, 2016#19
Originally Posted by SirDigby ↑
most likely will need re-pin on connector.

you posted "+other parts."
any other parts you are having issues locating?
Sadly yeahh.... OEM bmw e30 bottlecap wheels THIS! Picture not included in this copy

RECARO seats I maybe found someone but I need to save 700 canadian bucks for it.......
SirDigbyDenver, Colorado · Nov 24, 2016#20
I don't have anything on BM parts.
ACKING_QCThread starterQC, Canada · Nov 24, 2016#21
Originally Posted by SirDigby ↑
I don't have anything on BM parts.
does this means you have spare Toy parts ?
SirDigbyDenver, Colorado · Nov 24, 2016#22
uh...I have a spare intake manifold. I could even modify it for 1zz throttle body. I can also do a light port job for better flow. I could even add a 1zz to it, if you want me to source one out. I can paint it. (if you check out my photo album, you can see what I did) i'd even cut the rivets off for chip swap. each one would cost more money. (I can give you materials to make TB spacer, but it took me so long to make it I don't want to make another one) I also have a RS lower grill, but it would not fit on a USDM/CDM bumper.US/C stock Toyota front emblem. US/C stock tail lamps.

that's the only spare parts I have at this time.
ACKING_QCThread starterQC, Canada · Nov 24, 2016#23
1zz throttlebody.. Everyone seems to have one.. What does it do to our beloved punchy egg?
SirDigbyDenver, Colorado · Nov 24, 2016#24
well, the drive by wire limits the TB opening speed and it only opens to 80% at WOT. the 1zz is a little over 10% larger opening. it increases the flow where pedal feels more linier and increases flow at WOT. it's really a great improvement and feeling! (you do need to adjust the cold idle screw upon installation) I get a small stumble at about 2000 rpm on decal where the computer gets a little confused expecting to see one flow number, (mapping) but flow is higher. it just happens once in a great wile. sort of a "hick-up" feeling. not an issue really when the benefit is so much greater.
ACKING_QCThread starterQC, Canada · Nov 25, 2016#25
Hmm might have to dig one of them in a kenny u puul or similar.. Does a 2zz throttlebody does the same ? 'Cause if I remember I have a crashedout matrix in a kenny near me with a 2zz (tottally dead engine) but maybe the TB is still there..
SirDigbyDenver, Colorado · Nov 25, 2016#26
oh sorry. that's what I meant. it's the matrix/vibe/corolla engine. 1.8 I got mine from a matrix.
ACKING_QCThread starterQC, Canada · Dec 7, 2016#27
Finally got my hands on some BMW BottleCap !!! if all my plans are going right, I'm buying them saturday !! gotta put some rubbers on it tho.... the guy who is selling me these awesome things said that it is 185/65/15 and from what I searched on the web, these are some 0 offset wheels .. considering I had 175/65/15 with (IDFK what the stock offset is but I think my mags were stock Yaris offset) I'm sure they will fit in aand they will be flush / maybe stick out a bit which will give her an awesome look I think


I stole the idea of BC Wheels from this guy who them on his Sedan Echo which looks like this : https://www.youtube.com/watch?v=RMkN0odpbDQ (8:28 for final result)
WeeYariGeorgetown, Ontario, Canada · Dec 7, 2016#28
Stock offset is +42, so you'll be looking at nearly 2 inches pushed out further. These will go beyond flush!
ACKING_QCThread starterQC, Canada · Dec 7, 2016#29
Originally Posted by WeeYari ↑
Stock offset is +42, so you'll be looking at nearly 2 inches pushed out further. These will go beyond flush!
now THAT is good !
yarisugiハワイ · Dec 7, 2016#30
Originally Posted by ACKING_QC ↑
the guy who is selling me these awesome things said that it is 185/65/15 and from what I searched on the web, these are some 0 offset wheels .. considering I had 175/65/15 with (IDFK what the stock offset is but I think my mags were stock Yaris offset) I'm sure they will fit in aand they will be flush / maybe stick out a bit which will give her an awesome look I think
I doubt they are 15" tires since bottle caps are 14x6 et35.
ACKING_QCThread starterQC, Canada · Dec 8, 2016#31
How can I be sure of that ?
SirDigbyDenver, Colorado · Dec 8, 2016#32
Originally Posted by ACKING_QC ↑
now THAT is good !
ehh....it can cause some breaking issues...
ACKING_QCThread starterQC, Canada · Dec 9, 2016#33
That is not like the gap will be extreme ... 2" isn't thats bad.. Look at the Camberghini on youtube.. Now THAT is dangerous.. Sick and lit af but dangerous!
ern-dizCA all day · Dec 9, 2016#34
Wow.

I can't stand camber, but Camberghini just became my newest fascination.
ACKING_QCThread starterQC, Canada · Dec 10, 2016#35
forget about the bottlecap.. asked the owner to send me other pics..... aluminium aws damaged.. and rear of the mags was burnt as helll... mybe it was his drifting mags.. but damn !
WeeYariGeorgetown, Ontario, Canada · Dec 10, 2016#36
Good thing since you may have ended up looking something close to this. Maybe not quite as much poke since these wheels shown here are slightly wider. You definitely would not be lowering without stretch, camber, and fender rolling.

Picture not included in this copy

Picture not included in this copy
ACKING_QCThread starterQC, Canada · Dec 12, 2016#37
I do not want to lower the yaris anytime soon, I want a Rally themed one.. The bottlecaps were supposed to be the first touch.. But I need some pretty decent ones.. Not some old ass poked mags used 3 years ago for drifting
enviriCT · Dec 13, 2016#38
I don't know how cheap you are, but you can always get some oz wrc wheels. @ 15x6.5 +37