Yarisworld Archive

Toyota Yaris gs mk1 x reg won't start

30 posts · 10,863 views

InteltechOriginal postMiddlesbrough · Nov 5, 2016#1
Hey all i was wondering if anyone could please help. I have the above car which won't start. When you turn the key it cranks and sounds like it wants to start but won't. Checked all the usual fuel, battery, connections and still won't start. Battery isn't that old in fact less than a year old coming upto a year. I am thinking of scrapping if I can't get it going again. Was working albeit a bit sluggish and throaty until one. Ugh the I was driving and it lost power and started to die until I stopped and engine stalled and won't start back over. I changed the cam shaft sensor to a different one I had spare in the boot and it sounded a bit better but still refused to start. Garage has said it's the ecu but I aren't sure had other people look and say different things. I will try and get a video or sound file of what it sounds like at the moment tomorrow and try and upload somehow. Thank you for taking the time to read and any help you can give is much appreciated

Replies 29

jraIndiana · Nov 6, 2016#2
remove a plug wire-coil and see if it's getting spark, if not and you know your cam sensor is good, it could be the crank sensor? If it's getting spark, check fuel pressure, you can be getting fuel with very little pressure, needs to have enough pressure for injectors to atomize fuel. If fuel pressure is good, put test light on a injector wire and crank engine, light should flash on and off, if not injectors aren't working, could be bad relay bad ground someplace or the ECM. may also want to check mas air flow sensor sensor, maybe give it a good cleaning, but be careful, they are very delicate.
InteltechThread starterMiddlesbrough · Nov 9, 2016#3
Thank you for your reply. What would you recommend to clean the maf sensor? Also I have never removed the sparks plugs in this car so don't have a removal tool what size socket is needed. A garage thinks it is the ecu under the dash where the glove box is. Also how would I perform a pressure test for the fuel? Thank you again for the advice.
Bluevitz-rsOshawa, Ontario, Canada · Nov 10, 2016#4
what year is it?
InteltechThread starterMiddlesbrough · Nov 10, 2016#5
It's an x reg 2000
Bluevitz-rsOshawa, Ontario, Canada · Nov 10, 2016#6
What's an "x reg"?
InteltechThread starterMiddlesbrough · Nov 11, 2016#7
The registration of the car is X247ycu which makes it a 2000 model
Bluevitz-rsOshawa, Ontario, Canada · Nov 11, 2016#8
Spark plugs are a standard 5/8 socket, or 16mm if you can't get one. Fuel pressure can only be tested with an in line gauge installed where the fuel rail connects to the flexible line under the hood.

Why does the garage think it is the computer?
InteltechThread starterMiddlesbrough · Nov 11, 2016#9
They think it's computer cause they couldn't get any codes from the obd2 port and apparently there's no lights on the dash when you try and start it but yet the dash comes on as normal. The check engine light is on but again I have tried reading codes and nothing there.
Bluevitz-rsOshawa, Ontario, Canada · Nov 11, 2016#10
Double check the grounds are clean on the side of the head by the air box. That is where the computer ground to. If they are corroded it can cause the computer problems.
InteltechThread starterMiddlesbrough · Nov 11, 2016#11
Thanks I didn't know that I will check tomorrow and report back any news.
InteltechThread starterMiddlesbrough · Nov 30, 2016#12
I will try and get a picture uploaded later but I have just took all the ignition coils out and going from drivers side to passenger the one closest to the left has brown on it and also the hole where it goes is brown too the same as the one next to it then the two on the right don't have any brown in the holes or on the coils.
InteltechThread starterMiddlesbrough · Dec 27, 2016#13
Finally today managed to take the spark plugs out. The 2 on the drivers side which the holes have quite a bit of browning have a dark brown/black band running around the ceramic part and the threads are dark and the electrode is dark as well gap looks fine though. The 2 on the passenger side have a thin light brown ring going round the ceramic part and the threads and electrode are again dark in colour but not as dark. Out of curiosity I swapped the plugs over so the passenger ones are now the drivers side and same with the ignition coils. The plugs have quite a strong oily and petrol smell to them.
KimmoKekkiFinland · Dec 27, 2016#14
Did it fired up ?
InteltechThread starterMiddlesbrough · Dec 27, 2016#15
No in fact it sounded worse and hardly tried to start this time
InteltechThread starterMiddlesbrough · Dec 30, 2016#16
Well had a friend have a look at the car today which still won't start. Even tried swapping spark plugs with his new ones out of his Peugeot 106 plugs fitted fine but car still wouldn't start however he noticed that both mine and his sparks plugs after being removed had fuel on them which he said isn't normal they are usually dry which I noticed when he took his out of his car. He thinks the engine might be flooded anyone any ideas how to check this and solve it.
Bluevitz-rsOshawa, Ontario, Canada · Dec 30, 2016#17
Change the oil. You'll probably need to put a small amount of oil down the spark plug holes now if it's flooded really bad. A really badly flooded engine can actually start pushing fuel past the rings washing the cylinder bores and contaminating the oil.
InteltechThread starterMiddlesbrough · Jan 2, 2017#18
So do I have to do a full oil change and filter change? Or are you saying put a little oil in each spark plug hole then put spark plugs back in and try again?
Bluevitz-rsOshawa, Ontario, Canada · Jan 3, 2017#19
IF gasoline has contaminated the oil, change everything.

Oil in the cylinders is there to lubricate AND seal the rings to build compression.
InteltechThread starterMiddlesbrough · Jan 3, 2017#20
How do I know though if it is contaminated as when you take the plugs out they aren't exactly oily just wet and smells like petrol
InteltechThread starterMiddlesbrough · Jan 16, 2017#21
Had someone have a look and they seem to think it's an electrical fault somewhere battery is fine but when they tested cables going to ignition coils there was only power indication to one of the wires going into the connector. It was like this on a few different connectors.
Bluevitz-rsOshawa, Ontario, Canada · Jan 16, 2017#22
There is power to only one wire.
InteltechThread starterMiddlesbrough · Jan 16, 2017#23
He said the individual coloured wires that go into the connector there's only power on the end one where each wire should give an indication
Bluevitz-rsOshawa, Ontario, Canada · Jan 16, 2017#24
There should only be 12v on the Black with Red stripe wire. That is the only power source. Black with white wire is ground.
InteltechThread starterMiddlesbrough · Jan 16, 2017#25
TBH that makes sense to me still non the wiser as to why the car won't start
InteltechThread starterMiddlesbrough · Feb 27, 2017#26
Well replaced spark plugs and ignition coils and still won't start tried reading fault codes and the reader won't connect to the car reader just keeps restarting did get it to connect once but no codes found (check engine light is on) so I am at a loss.
jraIndiana · Feb 27, 2017#27
You haven't really said if it's getting spark or not? New coils and plugs won't help if computer isn't telling coils to fire. If you are sure the cam sensor is good, check the crank sensor, if it's good then it is most likely something wrong with wiring, grounds or the ecm it's self.
InteltechThread starterMiddlesbrough · Feb 28, 2017#28
I have tried to check spark but can't see from the drivers door so need to find someone to stand and check or turn key so I can check. As for cam sensor and crank sensor I can't get the code reader to display any codes so I have no idea if these are any good I replaced the cam sensor a while ago with a second hand one pulled from a t sport that was being broken as it was showing as a fault. How would I test these parts with not having any codes displayed to indicate a problem.
jraIndiana · Mar 4, 2017#29
You can remove sensors connect a volt meter to then set on ohms, then move a piece iron or steel in front of it and meter should show current each time iron is moved past sensor.
Bluevitz-rsOshawa, Ontario, Canada · Mar 4, 2017#30
Originally Posted by jra ↑
You can remove sensors connect a volt meter to then set on ohms, then move a piece iron or steel in front of it and meter should show current each time iron is moved past sensor.
You won't read current set on Ohms. To read current you need to set it to amps. To read voltage you need to set it to AC volts on a low scale.

But each sensor will have a resistance measurement according to the repair manual. The best place to measure this is at the connecter of the ECU. That way you are reading any problems with the wire harness along with the sensor