Yarisworld Archive

Spare tire relocation forward plan photo red Yaris 2007

17 posts · 6,332 views

dogsridewithOriginal postUSAnotCA · Sep 29, 2016#1
Picture not included in this copy
For weight redistribution to drive wheels, and to maximize a flat low load floor when rear seats and all the trays and lids are removed. Not FOR cosmetic, but wouldn't consider it if unpleasing or likely to increase aerodynamic drag.
Mount will probably extend through grill opening(s) to structure behind. Any direction on where here to find bumper cover removal method will advance this project. Also, any examples of Yaris set up to tow behind an RV might reveal useful attachment points.

Replies 16

WeeYariGeorgetown, Ontario, Canada · Sep 29, 2016#2
Wait! It's not April 1st is it?


Sent from my iPhone using Tapatalk
SirDigbyDenver, Colorado · Sep 29, 2016#3
this is silly.
bumper cover removal is super easy. remove 5 clips on top, 1 clip in each wheel well. like 4 bolts underneath. pull at a corner/wheel well, press clipped in under lights.
tmontagueCaledonia Ont. · Sep 30, 2016#4
I'm still not sure if this is a joke or not...
dogsridewithThread starterUSAnotCA · Sep 30, 2016#5
Not joking on spare or difficulty figuring out clips. When first got the car had to replace different location marker lights on each side for inspection. Looked like bumper cover removal should be easier than pulling battery and air-box and a couple other things. Got all the obvious clips on top and bolts underneath, but something on each side just didn't reveal how to release without blind yanking risking breaking plastic. Does the shop manual show any little pictures? or just say "release clips?"
(How many of your wiring problems are because some frustrated mechanic couldn't find the release tooth lever in one of Toyota's no-two-connectors-can-be-the-same...so just pried and pulled on the harness until it opened?)
Sorry to dis on your favorite car, but some stuff is just too hard to service. First step in my 91 Corolla's heater core replacement is "Disassemble interior, dash and centerstack. See Chapters..." A forum thread here indicated Yaris heater core might be similar?
WeeYariGeorgetown, Ontario, Canada · Sep 30, 2016#6
It seems scary. Feels scary, but to release the clips where bumper cover meets fender it is just a matter of giving it a good quick sharp tug. The clips will pop out. I was nervous as hell doing it the first time.
dogsridewithThread starterUSAnotCA · Sep 30, 2016#7
Thanks!
WeeYariGeorgetown, Ontario, Canada · Sep 30, 2016#8
Bumper cover off and this is what you'll looking at.

Picture not included in this copy
dogsridewithThread starterUSAnotCA · Sep 30, 2016#9
Looks like a mount will be easy. Thanks for that photo.
(Too bad Toyota Mind didn't put the towing eyebolt in the center...like the world instrument pod.)
WeeYariGeorgetown, Ontario, Canada · Sep 30, 2016#10
Originally Posted by dogsridewith ↑
(Too bad Toyota Mind didn't put the towing eyebolt in the center...like the world instrument pod.)
Well they did have to tie it into the frame rail in order to get a strong enough attachment point to haul the vehicle out of a ditch.

How 'bout you kill two birds with one stone. Take the recent thread where some dude is asking about mounting a Tacoma brush bar onto the Yaris, figure that out, then attach your spare to it.
MadMaxSan Antonio, Texas! · Sep 30, 2016#11
Why would you want to add all that weight in front of the front axle? It will throw off the handling of the car. The spare makes the most sense being stored where it already is.

I honestly doubt your sincerity with this...
Jason@SportsCarDebary, FL · Sep 30, 2016#12
Originally Posted by dogsridewith ↑
Picture not included in this copy
For weight redistribution to drive wheels, and to maximize a flat low load floor when rear seats and all the trays and lids are removed. Not FOR cosmetic, but wouldn't consider it if unpleasing or likely to increase aerodynamic drag.
Mount will probably extend through grill opening(s) to structure behind. Any direction on where here to find bumper cover removal method will advance this project. Also, any examples of Yaris set up to tow behind an RV might reveal useful attachment points.
You are doing it wrong. Notch the wiper tray and mount it on top of the engine. 🎉 😆

Picture not included in this copy
ern-dizCA all day · Sep 30, 2016#13
🤣
DeatheggCA · Oct 1, 2016#14
Oh Lord....

My Renault 5 (Le Car) had the spare on top of the engine. Not sure why! Leave the spare where it's at, build your flat load floor on top of that, when you remove the rear seats, etc.
ezhacker1San Francisco · Oct 1, 2016#15
Picture not included in this copy

attach it to the hatch outside, make a tiny SUV, like scotts Crashy.
Bluevitz-rsOshawa, Ontario, Canada · Oct 3, 2016#16
That's going to seriously hinder airflow to the rad and condenser.
alias06MN · Nov 17, 2016#17
I don't think that it'll have any real adverse affects on the cooling system. I have installed a custom grill that basically blocks off the top grill and haven't had any cooling issues, been driving as is for many years now.