Yarisworld Archive

The auto trans > manual trans conversion guide

44 posts · 38,750 views

ArmstrongRacingOriginal postSan Diego · Jul 3, 2016#1
Here we go again with another big project, haha. If your Yaris has a automatic transmission and you want to know what's needed to get a manual trans in there, take a look.

1)Transmission and 75W90 fluid
2)*Axles can be reused*
3)Shift cables
4)Floor shifter assy
5)Clutch/brake pedal assy
6)Brake master cylinder for manual trans car
7)Clutch master cylinder and line to brake reservoir
8)Clutch slave cylinder, bolts and lines
9)Clutch kit and bolts
10)flywheel and bolts
11)ECM/Wiring
12)MT mounts

Replies 43

ArmstrongRacingThread starterSan Diego · Jul 3, 2016#2
I like to remove the engine and trans for this project, it gives you more room to work in the engine bay.

First step, remove the engine and auto trans, then split the two by removing the 6 12mm bolts behind the access cover, then remove the 14mm bell housing bolts and set your engine on a stand while you prep the chassis.

1 attachment not included in this copy

ArmstrongRacingThread starterSan Diego · Jul 3, 2016#3
The pedals:

The AT brake pedal is one piece with one connector. You want to remove the pedal assy by disconnecting the brake light switch, then the return spring, then the pin to the booster. You then need to remove the upper dash pad via the service manual, then remove the top 12mm bolt. Now you can remove the (4) 12mm nuts on the main pedal bracket and pull the pedal out.

The MT pedal assy is 2 pieces, a clutch pedal and a brake pedal. (Before installation of the pedals you should install the clutch master). Start the install by sliding the clutch pedal assy over the clutch master studs and loosely attach the nuts, then install the top 12mm bolt and torque it all down. Attach the clutch master pin into the pedal and the return spring and plug in the clutch switch. Next, follow the same steps to install the brake pedal assy.

1 attachment not included in this copy

ArmstrongRacingThread starterSan Diego · Jul 3, 2016#4
Clutch master install:

The automatic cars have no holes where the clutch master mounts, so you need to line up the clutch pedal withe the top bolt hole, trace the holes in the bracket, then drill out the holes. You can now slide the clutch master in and attach the hydraulic lines.

1 attachment not included in this copy

ArmstrongRacingThread starterSan Diego · Jul 3, 2016#5
The brake master cylinder:

The MT part is different in only one way, it has a port on the bottom for the clutch hydraulics. You need to install the clutch master first because it's hard to get to. Start this by using a little 10mm line wrench to break loose the two brake lines on the master, then remove the (2) 12mm nuts holding the master to the brake booster. Unthread the brake lines the rest of the way then pull the master straight out of the booster.

You install the MT brake master then attach the hose from the clutch master on the side. Don't forget to fill with brake fluid and bleed the brakes/clutch once everything else is complete.

1 attachment not included in this copy

ArmstrongRacingThread starterSan Diego · Jul 3, 2016#6
The shifter and cables:

You can see here the difference in the two cables, MT on the left and AT on the right. This is pretty easy, disconnect the cable ends and then get under the car. Remove the exhaust heat shield and then remove the (3) 10mm nuts securing the cable pass-through seal. Now you can just pull the AT cable out from the bottom, then feed in the 2 MT cables and secure the seal. The AT floor shifter is just (4) 12mm bolts and two electrical connectors, then install the MT shifter and connect the cables.

1 attachment not included in this copy

ArmstrongRacingThread starterSan Diego · Jul 3, 2016#7
Flywheel and clutch:

The clutch and flywheel you need depends on your engine. If you keep your 1nz then a Yaris clutch is fine. But if you have a 2zr like me, you need these parts from a Scion Xd. You will also need flywheel bolts since they are different from the AT. Here is a picture of a Scion Xd disc on my Yaris C50 transmission...

1 attachment not included in this copy

ArmstrongRacingThread starterSan Diego · Jul 3, 2016#8
The Yaris C50 transmission:

This is the easiest MT to swap in, you just need the mounts and this will go right in.

1 attachment not included in this copy

ArmstrongRacingThread starterSan Diego · Jul 3, 2016#9
The trans install.

You will need the lift the engine off of its stand and get someone to hold the engine steady while you line up the transmission. First you put a small amount of grease on the input shaft and dowel pins, then you line up the input shaft with the clutch disc hole and wiggle/rotate the trans to align the two. When the shaft and disc align the trans will slide in and then you just align the dowel pins and install all of the bolts, but don't tighten until you get the starter in too.

1 attachment not included in this copy

ArmstrongRacingThread starterSan Diego · Jul 3, 2016#10
Reserved for clutch slave
ArmstrongRacingThread starterSan Diego · Jul 3, 2016#11
Reserved for wiring
rabbitoThailand · Jul 10, 2016#12
just shift through gears...only 4 speed with tiny little engine...😂😂😂😂😂

Sent from my SM-J700F using Tapatalk
07dirtyarishillview, ky · Jul 11, 2016#13
I'm glad you are doing a write-up on this. I've been sourcing parts for a while to do this same project.
As soon as I get my subie to be a stable DD I'm going to do this same swap.

Look forward to watching your progress
ArmstrongRacingThread starterSan Diego · Jul 12, 2016#14
For those of you like me that want to maximize you acceleration, there is a complete drop-in 4.31 final drive available from the 04-06 Scion Xb. I scored this from a wrecked car and it had case damage, but the gears are still in good condition. This upgrade will change your in-gear top speeds to the following:

1st- 29mph
2nd- 54
3rd- 80
4th- 101
5th- 121

1 attachment not included in this copy

CrankyOldManWest Michigan · Jul 12, 2016#15
So sex. The mechanical engineer in me gets a chubby looking at this stuff. The electrical engineer, on the other hand, doesn't give a flying rat's ass. ;)
ArmstrongRacingThread starterSan Diego · Jul 13, 2016#16
And a bit of engine enamel to spice things up

1 attachment not included in this copy

ArmstrongRacingThread starterSan Diego · Jul 22, 2016#17
Update:

The ARtrackbox case is done and prepared for assembly. We're just waiting on the Cusco LSD

1 attachment not included in this copy

ArmstrongRacingThread starterSan Diego · Aug 10, 2016#18
Update: it should be around 5 weeks for the LSD to get here, that gives me time to decide on a flywheel
rabbitoThailand · Aug 11, 2016#19
👍👍👍👍👍👍

Sent from my SM-J700F using Tapatalk
ArmstrongRacingThread starterSan Diego · Aug 12, 2016#20
We disassembled, cleaned, inspected, and transferred the C50 gears over to the Scion driven shaft today.

1 attachment not included in this copy

brushforhireJohnstown, PA · Aug 12, 2016#21
Love watching this project.
ArmstrongRacingThread starterSan Diego · Aug 12, 2016#22
Here is a side by side comparison of the Yaris & Xb C50 driven shafts. As you can see, the only difference is the number of pinion teeth.

1 attachment not included in this copy

ArmstrongRacingThread starterSan Diego · Aug 22, 2016#23
The differential bearings and seals showed up today, only 7-9 more weeks until the Cusco LSD arrives lol

1 attachment not included in this copy

ArmstrongRacingThread starterSan Diego · Sep 6, 2016#25
Disassembled, cleaned and measured all of the input shaft parts today. All is well, onto the Cusco LSD prep.

1 attachment not included in this copy

Bluevitz-rsOshawa, Ontario, Canada · Sep 7, 2016#26
synchro rigs are all in good shape?
rabbitoThailand · Sep 7, 2016#27
looking great!! 👉👉👉👉👉👉👉👉

Sent from my SM-J700F using Tapatalk
ArmstrongRacingThread starterSan Diego · Sep 7, 2016#28
All syncro gaps are well within spec, and they lock onto the gears.

1 attachment not included in this copy

ArmstrongRacingThread starterSan Diego · Sep 7, 2016#29
Here is the stock open differential on the left, and the Cusco differential on the right... For comparison

1 attachment not included in this copy

ArmstrongRacingThread starterSan Diego · Sep 8, 2016#30
Here is the Cusco LSD assembled and ready for install with the new Toyota bearings and the Scion 4.3 final drive

1 attachment not included in this copy

ArmstrongRacingThread starterSan Diego · Sep 8, 2016#31
Here is the differential in the bell housing

1 attachment not included in this copy

ArmstrongRacingThread starterSan Diego · Sep 8, 2016#32
This is what the differential preload adjusting shim looks like. The one with FF is the shim and the other one is just a case specific washer. They go under the bearing races

1 attachment not included in this copy

ArmstrongRacingThread starterSan Diego · Sep 8, 2016#33
This is how you check preload, the spec is 6.9 - 13.8 inch pounds

1 attachment not included in this copy

ArmstrongRacingThread starterSan Diego · Sep 8, 2016#34
We didn't quite reach the 6.9, so I ordered the one size larger GG shim

1 attachment not included in this copy

ArmstrongRacingThread starterSan Diego · Sep 10, 2016#35
Here is the new GG shim we ordered

1 attachment not included in this copy

ArmstrongRacingThread starterSan Diego · Sep 10, 2016#36
The new shim was the perfect size, we are now at 10.0 inch pounds witch is right in the middle of the specified range (6.9 - 13.8). Now let's assemble the transmission.

1 attachment not included in this copy

ArmstrongRacingThread starterSan Diego · Sep 10, 2016#37
Here we have both shafts and all of the case components installed, time to seal it up.

1 attachment not included in this copy

ArmstrongRacingThread starterSan Diego · Sep 17, 2016#38
The main case is sealed, and 5th gear assembly installed

1 attachment not included in this copy

ArmstrongRacingThread starterSan Diego · Sep 17, 2016#39
Slide the shifter assy in just to verity you can shift to all 6 gears, if so you can seal the end case

1 attachment not included in this copy

ArmstrongRacingThread starterSan Diego · Sep 17, 2016#40
Now you can install the shifter assy and all brackets/switches. Now you're ready to install the transmission

1 attachment not included in this copy

KasbienVancouver, BC · Jul 9, 2020#41
Thanks @ArmstrongRacing for taking the time to put this together! You rock man!

I know this is an old thread and all, but does anyone know if you'll lose your current odometer reading when swapping ECM? Can't seem to find a definitive answer in my searches.
Bluevitz-rsOshawa, Ontario, Canada · Jul 9, 2020#42
Originally Posted by Kasbien ↑
I know this is an old thread and all, but does anyone know if you'll lose your current odometer reading when swapping ECM? Can't seem to find a definitive answer in my searches.
No, the odometer reading is built into the dash.
KasbienVancouver, BC · Jul 10, 2020#43
Originally Posted by Bluevitz-rs ↑
No, the odometer reading is built into the dash.
Music to my ears. Thanks!
Abel teshomeEthiopia · Oct 23, 2022#44
Can u tell as abt the throtel wiring ? Tnx