fnkngrvOriginal postIn The Hotbox · Jun 7, 2016#1So we are halfway into the 2016 year and pretty much my update path for 2015 has been completed so I figured that I would catalog new setup changes in a new thread.
So if you missed the fact that I needed to upgrade my radiator once the built engine was put in and I started putting down at least 240whp/238tq back in 2014 I did a bunch of research and ended up going with a 92-00 Honda Civic 3 core aluminum half rad. My OEM rad/fan was hitting between 230-240° in stop-n-go. The rad over all seems like it is a good choice as my temps across the board dropped about 15°, but I'm not getting the temps I would like to see with the fan that came with it. Cruising at 60-65 she will sit between 180-195° and if in mild traffic in city around 200-205°. In constant yo-yo traffic on roadways it didn't take too long to sit at around 208-212° and then in true stop-n-go city stoplight type traffic she hits 225° and stays there. I have reached out to the site below to verify the mounting dimensions of their kit as I don't have much room to work with anymore with the IC piping and hose for the catch can. I have also picked up a Mishimoto Low Temp thermostat from someone which should help as well. I am thinking that this kit below especially having the shroud that it does will do the trick. Worse come to awful if the fan isn't enough the shroud will accept most universal fans out there so I could go with a different fan, but Honda guys with boosted builds on a bunch of forums have been pretty happy. I had been looking at a Spal or Proform, but to get higher CFMs (over 1k) is tough since those fans are typically almost 4" deep at the back of the fan motor.
92-00 Honda Radiator Fan and Shroud For reference I am using AMSOIL's Heavy-Duty Antifreeze & Coolant and water since it is allowed at venues where I race as the glycol in it is more environmentally friendly than the Toyota pink.
Replies 70
fnkngrvThread starterIn The Hotbox · Jun 7, 2016#2I finally got my Ecliptech iShift Progressive Shiftlight installed and working. Just need to tweak the calibration. I picked it up from MI during their clearance of inventory. To be honest it is so feature rich it is kind of a detractor from the product, but I have it now so will use it.
I decided to not use my Samsung Charge phone anymore as my GPS Speedo and plan on picking up a Speedhut 200mph unit eventually. I am reusing the custom mount I had for the iShift for now. I may end up moving the iShift later. Time will tell.
Picture not included in this copy
fnkngrvThread starterIn The Hotbox · Jun 7, 2016#3reserved.......
fnkngrvThread starterIn The Hotbox · Jun 7, 2016#4reserved.............
LTHatchNewark NJ · Jun 8, 2016#5Will the low temp thermostat affect your tune? Are there any hidden downsides to a low temp thermostat?
fnkngrvThread starterIn The Hotbox · Jun 9, 2016#6 Originally Posted by
LTHatch ↑ Will the low temp thermostat affect your tune? Are there any hidden downsides to a low temp thermostat?
It won't affect the tune at all. As for downsides the only upside is that low load driving will usually see lower operating temps. The biggest downside is that it will cause more wear since you generally sit below normal operating temp during that low load driving. The real results for the cooling system comes with the rad, shroud, and fan. Then lastly water pump if need be.
Sent from m-o-b-i-l-e
LTHatchNewark NJ · Jun 10, 2016#7Will you be uploading pictures of the new fan/shroud setup when you get it(review also)?
fnkngrvThread starterIn The Hotbox · Jun 10, 2016#8Most likely, but I think I am the only guy in the USA or even in North America with a Civic rad...haha
Sent from m-o-b-i-l-e
LTHatchNewark NJ · Jun 10, 2016#9Lol well you're one of the very few pushing these cars so it comes with the territory. Have you considering a oil cooler for your setup?
fnkngrvThread starterIn The Hotbox · Jun 10, 2016#10I have considered both an oil cooler and trans cooler for the last few years, but the biggest problem is real estate under the hood at this point. What could be a clever idea would be putting each down under the headlights where I have the openings for the fog lights. It would create drag, but the benefits may be worth it. They are traditionally small enough that I could possibly do it.
Sent from m-o-b-i-l-e
LTHatchNewark NJ · Jun 10, 2016#11How would you go about running a trans cooler on your MT?
fnkngrvThread starterIn The Hotbox · Jun 10, 2016#12It isn't easy and requires a dedicated pump and other components, but isn't something that I would need unless I decided to get into other types of racing. Nascar and some of the other racing orgs use them to include fuel dragsters. It would most likely be overkill in my situation, but sometimes my mind wanders into crazy ideas :-)
Sent from m-o-b-i-l-e
LTHatchNewark NJ · Jun 12, 2016#13What modifications are you looking to do this year?(other than the fan/shroud and shift light)
fnkngrvThread starterIn The Hotbox · Jun 12, 2016#14Mainly safety equipment. May be some other tidbits, but it all depends on a lot of other outside forces.
Sent from m-o-b-i-l-e
fnkngrvThread starterIn The Hotbox · Jun 15, 2016#15Roll cage tubing arrived and delivered. 1.75" x .120. Fingers crossed it and other safety equipment can get finished in time for the races mid July!
Picture not included in this copy
Picture not included in this copy
Sent from m-o-b-i-l-e
fnkngrvThread starterIn The Hotbox · Jun 15, 2016#16104k miles on the original rear brakes. Out with the old and in with the new.
Picture not included in this copy
Picture not included in this copy
Picture not included in this copy
Sent from m-o-b-i-l-e
Bluevitz-rsOshawa, Ontario, Canada · Jun 16, 2016#17did you have a hole burning in your pocket?
What's wrong with the old ones?
fnkngrvThread starterIn The Hotbox · Jun 16, 2016#18I felt more comfortable replacing them now with the increase in speeds I am looking to attain. Also I had my parking brake fully adjusted out and it wasn't really holding anymore on inclines out of gear. The rotors and shoes cost me $70 so it was cheap enough especially doing them myself.
They made it ten years so as far as I am concerned they had a good service life. You do the type of racing I do and you learn to not take "rule of thumb" to heart for reliability just at its face value.
Sent from m-o-b-i-l-e
Bluevitz-rsOshawa, Ontario, Canada · Jun 16, 2016#19No, if I did the racing you did, I'd be swapping in rear disc. Though, I already did that.
fnkngrvThread starterIn The Hotbox · Jun 16, 2016#20There has been plenty of discussions within the LSR community about rear drums and most keep them.
Sent from m-o-b-i-l-e
Bluevitz-rsOshawa, Ontario, Canada · Jun 16, 2016#21I would think that disc carry far less weight, especially at their outer edge and would lower rotating mass and improve acceleration
LTHatchNewark NJ · Jun 16, 2016#22How crazy are you going to go with that cage?
fnkngrvThread starterIn The Hotbox · Jun 17, 2016#23 Originally Posted by
Bluevitz-rs ↑ I would think that disc carry far less weight, especially at their outer edge and would lower rotating mass and improve acceleration
There have been a few guys that I have talked to that have made the change and they really didn't notice any difference when it came to speed or acceleration. Braking yes, but that is because they went not only disc, by also big brake. To me the cost being several hundred to upwards of a grand isn't worth it. Time will tell.
Sent from m-o-b-i-l-e
fnkngrvThread starterIn The Hotbox · Jun 17, 2016#24 Originally Posted by
LTHatch ↑ How crazy are you going to go with that cage?
It has to be a six point for up to 175. Over that will require a full. This one will have the main hoop, harness bar, front and rear legs. Depending I may go with a mid hoop angle leg however that isn't likely at this stage.
It should look something like this:
Picture not included in this copy Originally Posted by
LTHatch ↑ How crazy are you going to go with that cage?
It has to be a six point for up to 175. Over that will require a full. This one will have the main hoop, harness bar, front and rear legs. Depending I may go with a mid hoop angle leg however that isn't likely at this stage.
Sent from m-o-b-i-l-e
Bluevitz-rsOshawa, Ontario, Canada · Jun 18, 2016#25The cage doesn't require a diagonal section across the main hoop?
fnkngrvThread starterIn The Hotbox · Jun 18, 2016#26Every chassis is different on what they require. That above is just an example they provide. The cage design actually requires approval.
Sent from m-o-b-i-l-e
LTHatchNewark NJ · Jun 19, 2016#27Pretty good, did you get the chance to re-tune for even more power?
fnkngrvThread starterIn The Hotbox · Jun 19, 2016#28Not yet and may end up being on the fly if I do get to race in a month. Too much to get done and getting to the Dyno is tough as it is. Plans may be shifting some as the house just went under contract yesterday, but the goal is to still race in July and LDW.
Sent from m-o-b-i-l-e
fnkngrvThread starterIn The Hotbox · Jun 21, 2016#29Kill switch and associated wire ordered. Also ordered a hood pin/cable set as well.
Sent from m-o-b-i-l-e
fnkngrvThread starterIn The Hotbox · Jun 22, 2016#30Hood pins arrived
Picture not included in this copy
Sent from m-o-b-i-l-e
Bluevitz-rsOshawa, Ontario, Canada · Jun 22, 2016#31Just curious, how much is a good pin set like that?
fnkngrvThread starterIn The Hotbox · Jun 22, 2016#32Surprisingly cheap:
Picture not included in this copy
$19 with free prime shipping in the US
Sent from m-o-b-i-l-e
fnkngrvThread starterIn The Hotbox · Jun 24, 2016#33Kill switch and additional wire he arrived.
Picture not included in this copy
Sent from m-o-b-i-l-e
fnkngrvThread starterIn The Hotbox · Aug 3, 2016#34Been a while again. Been super busy with selling the house and getting ready to move to Texas.
Roll cage complete. Now to paint. Cage is 100% removable as well. 1 3/4" @ .120 sidewall. Good for up to 200mph. Then would need to go full cage then.
Picture not included in this copy
Picture not included in this copy
Picture not included in this copy
Picture not included in this copy
Picture not included in this copy
Picture not included in this copy
Picture not included in this copy
Sent from m-o-b-i-l-e
LTHatchNewark NJ · Aug 9, 2016#35Completely removable, so i assume you're going to bolt it into the car? That sounds almost insane a bolt in cage is rated to that speed, it looks damn good as always.
Hows the comfort of that Kirkey seat? You know you mean business when you have 10+ c16 5 gal tanks sitting in your garage lol
fnkngrvThread starterIn The Hotbox · Aug 9, 2016#36The cage has the 3/8" thick 6*6 top plats and then 3/8" 6*12 plates under the car. It is a standard setup for many subcompact cars out there. If I seem to have much more speed available then I will most likely go weld in because it will require me to upgrade to a full cage.
We use a ton of fuel each weekend. Carl's Mustang goes through 3-4 gallons alone per pass. Back in 2014 with the previous setup at 15psi I went through a half gallon per pass.
Sent from m-o-b-i-l-e
fnkngrvThread starterIn The Hotbox · Aug 9, 2016#37The racing seat isn't too bad. We are quite possibly cutting it and adding in an extra 1.5" because it is pretty snug already without the fire suit. I bought it used from my buddy (seat) for a fraction of the cost and he is only a 28" waist where right now I am a 38".
Sent from m-o-b-i-l-e
fnkngrvThread starterIn The Hotbox · Aug 9, 2016#38Hood pins installed. Pretty tight fit for sure, but managed.
Picture not included in this copy
Sent from m-o-b-i-l-e
LTHatchNewark NJ · Aug 10, 2016#39Half a gallon of C16 per run, its crazy to think any Yaris would ever consume that much. The hood pins look good, do you have weather stripping between your hood and bumper? Also where did you bolt the hood pins to (factory hood bump stomps?)?
fnkngrvThread starterIn The Hotbox · Aug 10, 2016#40I have weather molding but haven't installed it yet. As for the mounting location I can snap a picture of that too here later on today. Have to pick up the Highlander from Jason. He did repairs on it from a deer hit this spring.
Sent from m-o-b-i-l-e
LTHatchNewark NJ · Aug 10, 2016#41Please do take a picture of the mounting location, the Highlander survived a deer impact? You and yours are very fortunate, deer total loss everything they run into usually.
fnkngrvThread starterIn The Hotbox · Aug 10, 2016#42Had a deer try to jump over the hood of the truck. It laid onto the windscreen and then rolled along the driver's side to the fuel door. $2800 in damages. The last part to get fixed was the two doors which was done yesterday. Can't really tell but there were five heavy dents. Insurance wouldn't replace the door skins even though it would have been cheaper.
Picture not included in this copy
Here are the mounting points for the pins.
Picture not included in this copy
Picture not included in this copy
Also ditched the OEM upper grille in favor of a much less restrictive one from Thailand.
Picture not included in this copy
Sent from m-o-b-i-l-e
LTHatchNewark NJ · Aug 14, 2016#43That front grille looks aggressive, what are you going to do with the empty fog light holes?
fnkngrvThread starterIn The Hotbox · Aug 14, 2016#44I have LED angel eye fog lights, but haven't decided on if I will be installing them. Having the holes open means less resistance.
Sent from m-o-b-i-l-e
LTHatchNewark NJ · Aug 14, 2016#45Do things like fog lights or even the grille actually increase your top speed mph? I'm curious would removing your front bumper really add to your top speed run, or even slow you down a good bit.
fnkngrvThread starterIn The Hotbox · Aug 14, 2016#46Bumper removal will slow you down a lot. Having the fog holes open allows that air to pass through and roll over the tire rather than slam into the light housing and effectively cause it to build up a wall and then have to cascade around the bumper.
Sent from m-o-b-i-l-e
fnkngrvThread starterIn The Hotbox · Aug 14, 2016#47As for the grille I am mainly concerned about airflow to the radiator and intercooler.
Sent from m-o-b-i-l-e
LTHatchNewark NJ · Aug 14, 2016#48How does the grille affect the flow to the radiator and intercooler?
fnkngrvThread starterIn The Hotbox · Aug 14, 2016#49It is an open design. If you look at the OEM grille it has a lot more restrictive flow due to the plastic accents in it.
Sent from m-o-b-i-l-e
LTHatchNewark NJ · Aug 14, 2016#50At your top speed range, do little improvements like grille or fog lights give a noticeable gain? What's the biggest mph you had for a simple modification?