Yarisworld Archive

Build: Sound Quality In-Cabin Dual 10” Woofer Enclosure (Lots of PICS!)

13 posts · 4,801 views

juicyjoshOriginal postSan Francisco · Jan 8, 2016#1
Greetings Yaris Owners,

This build has the usual goals:


Sound Quality: Tight, accurate bass that would sound good regardless of whether it's hip hop, EDM, vocals or orchestra music, and anything else

No rattles

Bass energy focussed on the two front passengers

Kick in the back

Easy to move around

System flexibility/No compromise with regards to space

Stealth to avoid attracting unwanted attention



Hopefully sharing this build with the Yarisworld may spark some ideas for others for their own builds.

Positive constructive comments are welcome 🙂


Calculations and planning:

Picture not included in this copy

Replies 12

Bluevitz-rsOshawa, Ontario, Canada · Jan 8, 2016#3
is this going in a HB or Sedan?
mr_milesPortland, OR · Jan 9, 2016#4
All I care about is that rotor in the first picture. BRAP BRAP BRAP. I miss my RX7....
juicyjoshThread starterSan Francisco · Jan 10, 2016#5
Originally Posted by Bluevitz-rs ↑
is this going in a HB or Sedan?
This:

Picture not included in this copy



Originally Posted by mr_miles ↑
All I care about is that rotor in the first picture. BRAP BRAP BRAP. I miss my RX7....
mr_miles,

That's the dented rotor from my first blown engine.

Yeah, I miss it too.

Picture not included in this copy

aaand... the 17.4 lbs. of boost on a new engine with new Efini turbos 👍

Picture not included in this copy


Built a stealth system in the RX-7, too 🙄

Picture not included in this copy

Picture not included in this copy


We're back on topic in the next post 😉
MedMantleSouth Africa · Jan 10, 2016#7
I am so loving this so far. I have an 8" sub in a prefab box which was made for 2 subs that takes up my whole boot. I'm also in the process of making a stealth setup that's gonna look OEM. May even upgrade the 8" kicker for a 10" while I'm busy to get the best of both worlds :P \m/
1nz revolutiontx · Jan 10, 2016#8
A little Focal might sound better.

1 attachment not included in this copy

MedMantleSouth Africa · Jan 10, 2016#9
Hot stuff! I reckon I wanna see your build complete though for some inspiration as I am a total novice when it comes to woodwork etc.
juicyjoshThread starterSan Francisco · Jan 10, 2016#10
Originally Posted by 1nz revolution ↑
A little Focal might sound better.
1nz revolution,

I agree. That's why I bought a a set of open-boxed Focal 3-way components for the 2003 MR-S.

For subs, however, I've really been impressed with SoundQubed for their ultra-rigid lightweight cone, serious suspension, spring-loaded terminals, insane voice coil and completely exceptional quality.

This HDS208 dual 2-ohm 8" woofer is rated at 600 RMS, but it easily handles closer to 1000 off a Pioneer D-class without bottoming out.

Picture not included in this copy

Picture not included in this copy


Typical box-building materials. Maybe should have posted this earlier 😁

Picture not included in this copy


Ported enclosure mockup (for the 8" sub for the MR-S). Flush-mounted woofer, dual ports (for aesthetic symmetry) and rounded panels for improved efficiency, port aerodynamics and reduced port noise:

Picture not included in this copy


Ported enclosure construction. Notice the rounded port channels, pilot-drilled screw holes and straight-through 12-gauge OFC wires for the dual voice coils.

My dremel broke, and I didn't want to spend $40 to buy a new one 🤷 so all rounded panels were actually done by hand.

Picture not included in this copy


Open-box purchase for $360 on the Focal 3-ways 🤘

Picture not included in this copy


Removed the cheap soft rubber dust caps from the Focal 6-3/4 woofers to be replaced with homemade polypropylene caps:

Picture not included in this copy




Originally Posted by MedMantle ↑
Hot stuff! I reckon I wanna see your build complete though for some inspiration as I am a total novice when it comes to woodwork etc.
MedMantle,

Thanks! It just comes from creativity, experience and doing it right the first time, even if it means your project might take a little longer.
1nz revolutiontx · Jan 10, 2016#11
A little Audison will brighten it up.

1 attachment not included in this copy

09GLHBaltimore, MD · May 4, 2016#12
Updates?