dieselphreakOriginal postoklahoma · Feb 21, 2015#1Thanks in advance for any help. This is my mothers car, and became my problem after my step dad replaced the fuel pump in hopes of a cure. Lets start with the background. 2009 yaris, automatic, 170k. It died while driving, wouldn't start back up. Cranks just fine. I scanned it for codes with none found. I found that the fuel pump had voltage and would run during crank, but not for the initial key on. I can spray starting fluid down the intake and it will start but dies as soon as i stop spraying, with the fuel pump running the entire time, so it appears that I'm not getting any injector pulse. Any help would be MUCH appreciated ( my mom seems to want to call every hour and ask if I figured it out yet 🆘)
-Brian
Replies 47
WeeYariGeorgetown, Ontario, Canada · Feb 21, 2015#2CTScott is the man you need to hear from, but since he lives in the Northeast, he is probably out clearing snow.
dieselphreakThread starteroklahoma · Feb 21, 2015#3yeah we are supposed to get some of that tonight too. However, in oklahoma you can't believe what they say, its sunny and 65 right now, high of 23 tomorrow...
nortonfbmotown · Feb 21, 2015#4Did you pull the fuel line at the motor to make sure it's flowing?
Could be a filter.
CTScottUSA, CT · Feb 21, 2015#5It really sounds like the engine immobilizer is not happy and therefore not allowing the injectors to be driven. If the engine immobilizer light (on the dash by the windshield) is still flashing when the key is placed into the ignition, then the ECM is preventing the injectors from firing.
dieselphreakThread starteroklahoma · Feb 21, 2015#6I dont believe this model has an immobilizer, no light on the dash like my camry, and no extra plastic hardware around the ignition
CTScottUSA, CT · Feb 21, 2015#7 Originally Posted by
dieselphreak ↑ I dont believe this model has an immobilizer, no light on the dash like my camry, and no extra plastic hardware around the ignition
OK. I always want to say that it was standard on 09+, but forget that it was part of certain packages.
Check the following:
20 A EFI fuse in the under hood fuse panel
At the injectors, with the ignition switch in the on position, remove the connector from injector #1 (closes to the belt) and check for 12V on the green wire.
If that is present, check the following:
If you remove the lower steering column cover (two screws behind the steering wheel, which are visible when it is rotated slightly and a third by the tilt wheel lever) you can access the ignition switch connector.
On it, check the following:
Yellow and Grey wires should have 12V with ignition off
White should have 12V with ACC on
Green and Pink should have 12V with IG in ON position
Black should have 12V while cranking the starter
bronsinnj · Feb 21, 2015#8My 09 3 door basic hatch with auto....definitely no immobilizer! 🙇
dieselphreakThread starteroklahoma · Feb 22, 2015#9 Originally Posted by
CTScott ↑ OK. I always want to say that it was standard on 09+, but forget that it was part of certain packages.
Check the following:
20 A EFI fuse in the under hood fuse panel
At the injectors, with the ignition switch in the on position, remove the connector from injector #1 (closes to the belt) and check for 12V on the green wire.
If that is present, check the following:
If you remove the lower steering column cover (two screws behind the steering wheel, which are visible when it is rotated slightly and a third by the tilt wheel lever) you can access the ignition switch connector.
On it, check the following:
Yellow and Grey wires should have 12V with ignition off
White should have 12V with ACC on
Green and Pink should have 12V with IG in ON position
Black should have 12V while cranking the starter
Thank you sir! I will investigate this morning and report back my findings!
dieselphreakThread starteroklahoma · Feb 22, 2015#10 Originally Posted by
CTScott ↑ OK. I always want to say that it was standard on 09+, but forget that it was part of certain packages.
Check the following:
20 A EFI fuse in the under hood fuse panel
Voltage good, fuse good
Originally Posted by
CTScott ↑
At the injectors, with the ignition switch in the on position, remove the connector from injector #1 (closes to the belt) and check for 12V on the green wire.
12v present
Originally Posted by
CTScott ↑ If that is present, check the following:
If you remove the lower steering column cover (two screws behind the steering wheel, which are visible when it is rotated slightly and a third by the tilt wheel lever) you can access the ignition switch connector.
On it, check the following:
Yellow and Grey wires should have 12V with ignition off
White should have 12V with ACC on
Green and Pink should have 12V with IG in ON position
Black should have 12V while cranking the starter
all of the ignition wires checked out as well. Now I'm getting worried that it may be an injector driver issue in the PCM.
CTScottUSA, CT · Feb 22, 2015#11Try one more thing - Listen closely to the injectors while trying to start it to see if you can hear them clicking away.
dieselphreakThread starteroklahoma · Feb 22, 2015#12Negative. No noise
CTScottUSA, CT · Feb 22, 2015#13 Originally Posted by
dieselphreak ↑ Negative. No noise
OK.
Also, check the following:
AM2 fuse (in under hood)
Put your ear against the plastic block that that fuse is mounted to and listen for the relays inside to click. When someone inside the car turns the ignition from off to on, you should hear two relays click.
dieselphreakThread starteroklahoma · Feb 22, 2015#14That fuse is good, I also physically removed the integrated relay block and pulled them out and can physically watch them close also found out the third relay was the horn when I didn't see it close I used a toothpick to close it lol. The bruise on the back of my head should be gone in a few days lol
CTScottUSA, CT · Feb 22, 2015#15 Originally Posted by
dieselphreak ↑ That fuse is good, I also physically removed the integrated relay block and pulled them out and can physically watch them close also found out the third relay was the horn when I didn't see it close I used a toothpick to close it lol. The bruise on the back of my head should be gone in a few days lol
I LOLed on that one. Nothing better than physical comedy.
So, it really does sound like the ECM is the issue. If you can get your hands on one from a same tranny type 07-09, you can verify that very quickly. If you grab an 09, make sure it too is a non-immobilizer one.
Since you don't have the immobilizer, there are no issues with swapping it. If you happen to have a manual transmission, I have a spare one on hand that I could program with you VIN and ship to you.
dieselphreakThread starteroklahoma · Feb 22, 2015#16Its an automatic..
IllusionXBrossard, QC · Feb 22, 2015#17CTScott is really not the only one to LOL at the relay tooth picking. :)
dieselphreakThread starteroklahoma · Feb 23, 2015#18 Originally Posted by
IllusionX ↑ CTScott is really not the only one to LOL at the relay tooth picking. :)
yeah i'm 6'3" and was all hunched over that little thing, If i had a video it would be viral by now i promise that!
IllusionXBrossard, QC · Feb 23, 2015#19My horn decided to stick when i was doing something in the car in the garage.. i was almost deaf by the time i was able to pop the hood, get a 10mm wrench and disconnect the battery.
/offtopic
mario98cPuerto Rico · Feb 23, 2015#20Bad crankshaft sensor?
CTScottUSA, CT · Feb 23, 2015#21 Originally Posted by
mario98c ↑ Bad crankshaft sensor?
Not a bad thought. If the O.P. has access to a code reader, one would be stored if this is the case.
dieselphreakThread starteroklahoma · Feb 23, 2015#22no codes stored. I do have an rpm signal while cranking, however not sure where this particular car gets its rpm signal, be it the cam or crank sensor
dieselphreakThread starteroklahoma · Feb 23, 2015#23is it possible on this car that one sensor drives the coils while the other fires the injectors? However it should of set a code by now I'm sure.
CTScottUSA, CT · Feb 23, 2015#24 Originally Posted by
dieselphreak ↑ is it possible on this car that one sensor drives the coils while the other fires the injectors? However it should of set a code by now I'm sure.
With the way it dies, if it was the sensor, it would have thrown a code.
Does the CEL light when you turn the key to the on position?
ttr125fan09corpus christi, texas · Feb 23, 2015#25Just a shot in the dark, but did you try filling the tank? Alot of time the fuel level sensor is off by up to a quater tank. I've replaced dozens of them. Just worth a shot putting gas in it. Easy way to check injector pulse, take a led out of something and put it in the injector connector. See if it flashes. Simply a noid light.
Bluevitz-rsOshawa, Ontario, Canada · Feb 23, 2015#26And just to add, the fuel pump only operates while cranking until the engine has started.
dieselphreakThread starteroklahoma · Feb 24, 2015#27no injector pulse, that i have verified
interesting to know on the fuel pump, figured it would of had some sort of key on prime function
yes i get a cel with key on
CTScottUSA, CT · Feb 24, 2015#28 Originally Posted by
dieselphreak ↑ no injector pulse, that i have verified
interesting to know on the fuel pump, figured it would of had some sort of key on prime function
yes i get a cel with key on
The fuel pump actually comes on and stays on when the key is on. It does not shut off until the ignition is turned back off.
The CEL on tells me that the ECM is at least partially functioning, but I still think that it is the problem.
Bluevitz-rsOshawa, Ontario, Canada · Feb 24, 2015#29 Originally Posted by
CTScott ↑ The fuel pump actually comes on and stays on when the key is on. It does not shut off until the ignition is turned back off.
The CEL on tells me that the ECM is at least partially functioning, but I still think that it is the problem.
My bad, it only operates while cranking on my echo until the engine starts.
dieselphreakThread starteroklahoma · Feb 24, 2015#30Same with this car. Pump only runs while cranking or when it's running on starting fluid. Never with just key on
CTScottUSA, CT · Feb 24, 2015#31 Originally Posted by
dieselphreak ↑ Same with this car. Pump only runs while cranking or when it's running on starting fluid. Never with just key on
It should. If you listen by the rear of the car, you should hear the pump as soon as the key is in the ON position.
bronsinnj · Feb 25, 2015#32Definately the pump runs upon switching on the ignition. All the FI vehicles I ever owned did.
Bluevitz-rsOshawa, Ontario, Canada · Feb 25, 2015#33WeeYariGeorgetown, Ontario, Canada · Feb 25, 2015#34It would be messy, but would it not be advantageous at this point to disconnect the fuel line from the fuel rail?
If gas immediately flows out, you know your line is at least pressurized which is good. After that, if fuel still flows out of the line with key on or cranking, even better. Eliminates pump as a suspect would it not?
You know the coils are working as you can run the car by feeding fluid into the TB. That would leave you with an injector issue.
CTScottUSA, CT · Feb 25, 2015#35 Originally Posted by
WeeYari ↑ It would be messy, but would it not be advantageous at this point to disconnect the fuel line from the fuel rail?
If gas immediately flows out, you know your line is at least pressurized which is good. After that, if fuel still flows out of the line with key on or cranking, even better. Eliminates pump as a suspect would it not?
You know the coils are working as you can run the car by feeding fluid into the TB. That would leave you with an injector issue.
He has verified that the injectors are not pulsing. The fuel pump is definitely not the issue.
dieselphreakThread starteroklahoma · Mar 4, 2015#36Ok I'm still ready to condemn the ecu. However, let me clarify a few things.
The back seat is out of the car and I have wired up an LED to monitor pump operation. Nothing with key on, only while cranking or running on starting fluid
The new issue I noticed is AFTER you try to start the car and give up, there is a high pitched noise coming from the throttle body that only quits when you either unplug the throttle body or cycle the key. The battery isn't low either as I have been keeping a charger on it.
Also, my final question, since this car does NOT have the immobilizer, if I get a used ecu that came out of a 09 automatic with no immobilizer does it still need to be programmed?
dieselphreakThread starteroklahoma · Mar 14, 2015#37update: New pcm, still same results. I'm at a total loss here.
WeeYariGeorgetown, Ontario, Canada · Mar 14, 2015#38Your wasting time and money now. Time to get it hauled to a shop.
CTScottUSA, CT · Mar 14, 2015#39 Originally Posted by
dieselphreak ↑ Ok I'm still ready to condemn the ecu. However, let me clarify a few things.
The back seat is out of the car and I have wired up an LED to monitor pump operation. Nothing with key on, only while cranking or running on starting fluid
The new issue I noticed is AFTER you try to start the car and give up, there is a high pitched noise coming from the throttle body that only quits when you either unplug the throttle body or cycle the key. The battery isn't low either as I have been keeping a charger on it.
Also, my final question, since this car does NOT have the immobilizer, if I get a used ecu that came out of a 09 automatic with no immobilizer does it still need to be programmed?
Not really. The only reason to reprogram it is if your state does OBD emissions, where they plug into the car and expect it to respond with its proper VIN.
dieselphreakThread starteroklahoma · Mar 15, 2015#40ok, mild update,
i just ASSumed since the new pçm, that the injectors were not firing since it would still run off of starting fluid, however,
i have spark and injector pulse with the new pcm, just the fuel pump doesn't run,
old pcm the fuel pump runs, no injector pulse... *&$@$&*
CTScottUSA, CT · Mar 15, 2015#41 Originally Posted by
dieselphreak ↑ ok, mild update,
i just ASSumed since the new pçm, that the injectors were not firing since it would still run off of starting fluid, however,
i have spark and injector pulse with the new pcm, just the fuel pump doesn't run,
old pcm the fuel pump runs, no injector pulse... *&$@$&*
What's the ten digit (5-5) part number on the new one?
dieselphreakThread starteroklahoma · Mar 15, 2015#42ok, not sure what the deal was or what happened. but i went out there a few hours ago and tried it, it started, been running fine ever since. tried the old pcm just to see, no injector pulse, new pcm it runs. not sure but i'm damn sure happy! lol
Thanks everyone for your help!
Bluevitz-rsOshawa, Ontario, Canada · Mar 15, 2015#43👍
CTScottUSA, CT · Mar 15, 2015#44 Originally Posted by
dieselphreak ↑ ok, not sure what the deal was or what happened. but i went out there a few hours ago and tried it, it started, been running fine ever since. tried the old pcm just to see, no injector pulse, new pcm it runs. not sure but i'm damn sure happy! lol
Thanks everyone for your help!
If everything remains OK, I'd love to get my hands on the bad one to see what failed within it.
JEducateMilwaukee, Wisconsin · Mar 15, 2015#45Over the winter, my car's gas gauge was going back and forth to one bar to two bars left. It ended up stalling. Then, about a month ago, it said there was two bars left, and it stalled. I was hoping that it would be just frozen pipes. We have had a few warm days. I had to fill up my tank because it was stuck on three bars from the bottom. It will show it being filled up, but will stop at the third line. I read that it could be the indicators could be dirty. Any suggestions? Can I fix it myself, or do I have to go to a mechanic?
CTScottUSA, CT · Mar 16, 2015#46 Originally Posted by
JEducate ↑ Over the winter, my car's gas gauge was going back and forth to one bar to two bars left. It ended up stalling. Then, about a month ago, it said there was two bars left, and it stalled. I was hoping that it would be just frozen pipes. We have had a few warm days. I had to fill up my tank because it was stuck on three bars from the bottom. It will show it being filled up, but will stop at the third line. I read that it could be the indicators could be dirty. Any suggestions? Can I fix it myself, or do I have to go to a mechanic?
That would be a a bit if a threadjack, as your post is completely unrelated to that of the O.P. Typically when a gas gauge does that it is due to the resistive strip for the fuel level sender either being dirty or being worn. You can try adding fuel system cleaner to the tank, but if that doesn't help, then you are looking at having to have the sender removed and replaced.
JEducateMilwaukee, Wisconsin · Mar 16, 2015#47I know this was not related to the O.P. This is my first time on here and did not know how to do a new thread. Thanks for helping.
bronsinnj · Mar 16, 2015#48 Originally Posted by
JEducate ↑ I know this was not related to the O.P. This is my first time on here and did not know how to do a new thread. Thanks for helping.
Welcome to the forum, an excellent place to learn about your Yaris!👏