Santa (me) got my wife a sound system for her 2008 Yaris sedan and I'm now in the process of installing it.
Picture not included in this copy
Of course I need to take care of the lack of sound deadening the car has in its stock form and I'm going with the budget version.
Deadener -Stinger Roadkill Mat on metal to lower resonance.
Decoupler -Ultratouch thermal barrier on top of deadener/metal to decouple the Acoustical Barrier (MLV) and reduce heat transfer (100% coverage) I used aluminum foil tape to seal the seams and to keep the radiant barrier down. I bought the 48 in. x 24 ft. roll @ $59.98 /roll.
MLV - dB-3 Acoustical Barrier MLV (Mass Loaded Vinyl). MLV goes on top of radiant barrier. I bought two rolls @$29.99 / roll so I can do the floor as well as the doors.
Armacell’s 2 inch Armaflex closed cell foam tape as another form of decoupler and to help reduce rattles. I bought at least 4 rolls @ $7.85 / each, Rammat Ensolite IUO Peel and Stick @$17 / yrd would have been a better option but I did not want to wait for it to ship. I planned on using as much of the Ultratouch radiant barrier as I could as the decoupler but this tape is good for the small areas.
Extruded Butyl rope where the door skins meet the side impact beams. I had some left over from a projector headlight project I did on my Mark VIII.
Picture not included in this copy
I also have a 3, 2 inch thick sound deadening sheets that I've been cutting up and stuffing in any empty spaces I could find including the inner wheel wells (front & rear) and trunk area. I got her a set of SYLVANIA SilverStar Ultras for Christmas so I already had the head lights out and that made it easy to stuff the fender wells and add mat to the fenders themselves.
Considering this is a huge project I had to enlist some helpers as well as a supervisor (Jawa) to keep them focused...
Picture not included in this copy
I don't think it's working!
Picture not included in this copy
Picture not included in this copy
Anyway...
Picture not included in this copy
You can see the foam packed in the large open space over the rear wheel.
Picture not included in this copy
Picture not included in this copy
Picture not included in this copy
Picture not included in this copy
Interior gutted.
Picture not included in this copy
I noticed a plug was out when I pulled the carpet up.
Picture not included in this copy
Door speaker wire fishing fun.
Picture not included in this copy
Speaker adapters made the job easy.
Picture not included in this copy
Outer door skin is covered in the thermal barrier and I added some 2 inch foam on the floors as well. I installed the mat on the "other" side of the inner door panels to make room for the decoupler / MLV layers so the door panels would fit easier.
Picture not included in this copy
Pass side door ready for some work... She is driving my modified Focus ST so I need to hurry up on this install!
More to come...
Picture not included in this copy
Of course I need to take care of the lack of sound deadening the car has in its stock form and I'm going with the budget version.
Deadener -Stinger Roadkill Mat on metal to lower resonance.
Decoupler -Ultratouch thermal barrier on top of deadener/metal to decouple the Acoustical Barrier (MLV) and reduce heat transfer (100% coverage) I used aluminum foil tape to seal the seams and to keep the radiant barrier down. I bought the 48 in. x 24 ft. roll @ $59.98 /roll.
MLV - dB-3 Acoustical Barrier MLV (Mass Loaded Vinyl). MLV goes on top of radiant barrier. I bought two rolls @$29.99 / roll so I can do the floor as well as the doors.
Armacell’s 2 inch Armaflex closed cell foam tape as another form of decoupler and to help reduce rattles. I bought at least 4 rolls @ $7.85 / each, Rammat Ensolite IUO Peel and Stick @$17 / yrd would have been a better option but I did not want to wait for it to ship. I planned on using as much of the Ultratouch radiant barrier as I could as the decoupler but this tape is good for the small areas.
Extruded Butyl rope where the door skins meet the side impact beams. I had some left over from a projector headlight project I did on my Mark VIII.
Picture not included in this copy
I also have a 3, 2 inch thick sound deadening sheets that I've been cutting up and stuffing in any empty spaces I could find including the inner wheel wells (front & rear) and trunk area. I got her a set of SYLVANIA SilverStar Ultras for Christmas so I already had the head lights out and that made it easy to stuff the fender wells and add mat to the fenders themselves.
Considering this is a huge project I had to enlist some helpers as well as a supervisor (Jawa) to keep them focused...
Picture not included in this copy
I don't think it's working!
Picture not included in this copy
Picture not included in this copy
Anyway...
Picture not included in this copy
You can see the foam packed in the large open space over the rear wheel.
Picture not included in this copy
Picture not included in this copy
Picture not included in this copy
Picture not included in this copy
Interior gutted.
Picture not included in this copy
I noticed a plug was out when I pulled the carpet up.
Picture not included in this copy
Door speaker wire fishing fun.
Picture not included in this copy
Speaker adapters made the job easy.
Picture not included in this copy
Outer door skin is covered in the thermal barrier and I added some 2 inch foam on the floors as well. I installed the mat on the "other" side of the inner door panels to make room for the decoupler / MLV layers so the door panels would fit easier.
Picture not included in this copy
Pass side door ready for some work... She is driving my modified Focus ST so I need to hurry up on this install!
More to come...