Yarisworld Archive

Help finding part number

20 posts · 17,519 views

joellOriginal postPanama, Central America · Nov 12, 2014#1
Hello
The clear white plastic part that hold the rubber gromet of the hatch is loose,the water can leak inside the headliner.
I searched the catalog of parts but without luck, the part itself don´t have any marking that indicate a Toyota code XXXX-XXXX.

Silicone sealant and 3M tape cannot hold in place, Japanese Yaris 2013, sorry for the bad english

Picture lost · i61.tinypic.com

Picture lost · i58.tinypic.com

Thanks for any help

Replies 19

bairjoNov 13, 2014#2
I usually find that the local Toyota dealer can give that info in 5 minutes. try that.
CTScottUSA, CT · Nov 14, 2014#3
That white part is considered part of the complete hatch wiring harness. You can't purchase it separately from Toyota.
hondajtUnited States · Nov 14, 2014#4
You can make something out of hose sealer and silicon from Lowe's or Home Depot.
CTScottUSA, CT · Nov 14, 2014#5
Originally Posted by hondajt ↑
You can make something out of hose sealer and silicon from Lowe's or Home Depot.
The white plastic piece snaps into a large hole in the hatch opening and is designed to squeeze the molded lip on the black rubber boot to make a waterproof seal. When the hatch is open the black boot has a significant amount of tension on it as well.

You would have a difficult time making something to replace it and particularly finding a sealing compound that will stick to the painted metal and the rubber and form a completely waterproof seal (particularly for the O.P., who is in Panama, where it is hot and wet).
hondajtUnited States · Nov 14, 2014#6
Originally Posted by CTScott ↑
The white plastic piece snaps into a large hole in the hatch opening and is designed to squeeze the molded lip on the black rubber boot to make a waterproof seal. When the hatch is open the black boot has a significant amount of tension on it as well.

You would have a difficult time making something to replace it and particularly finding a sealing compound that will stick to the painted metal and the rubber and form a completely waterproof seal (particularly for the O.P., who is in Panama, where it is hot and wet).
Yikes, yeah, I don't think I completely understood how it operated.....so in hindsight....the better idea is definitely to go buy the harness (and part) from the dealer or online.

Good luck.
joellThread starterPanama, Central America · Nov 14, 2014#7
Thanks for all the responses 👍

I will evaluate all the options available:
1. Buy the whole harness
2. Search in the junkyard, some new yaris have crashed
3.Another post have a lead for possibles replacements, partial Part Name Code (82819-XXXXX) that will investigate more.

The best advice I can give is: Be careful when installing any reverse camera
Eduardo_mtyNov 14, 2014#8
Ctscott do you know the part number of hatch Wiring harness.

Joell i did the same "error" when i try to install reverse camera
CTScottUSA, CT · Nov 14, 2014#9
Originally Posted by Eduardo_mty ↑
Ctscott do you know the part number of hatch Wiring harness.

Joell i did the same "error" when i try to install reverse camera
Any of these:

82184-52320
82184-52340
82184-52350
ucsmfuvancouver, BC · Nov 15, 2014#11
what is the best way to remove that plastic part when removing the reverse camera ?
CTScottUSA, CT · Nov 15, 2014#12
Originally Posted by ucsmfu ↑
what is the best way to remove that plastic part when removing the reverse camera ?
Squeezing the tabs from below is the only way to remove it without deforming it.
ucsmfuvancouver, BC · Nov 15, 2014#13
Originally Posted by CTScott ↑
Squeezing the tabs from below is the only way to remove it without deforming it.
to access to the tabs below, will I need to remove the headliner ?

thanks
CTScottUSA, CT · Nov 15, 2014#14
Originally Posted by ucsmfu ↑
to access to the tabs below, will I need to remove the headliner ?

thanks
Partially, or get your hand up between it and the roof.
joellThread starterPanama, Central America · Dec 21, 2014#15
Update: I take the broken part to a 3D printing shop, they scanned and printed in black ABS, cost $30 dollars.

Picture lost · i62.tinypic.com

Picture lost · i60.tinypic.com
Eduardo_mtyDec 21, 2014#16
Do you have a finished printing part.


Where are you located ?
Eduardo_mtyDec 21, 2014#17
Picture from finished part printing
joellThread starterPanama, Central America · Dec 21, 2014#18
This is the finished printed part, i dont have the computer archive of the 3D model.But you can search locally for some place that can help you: http://www.3dhubs.com/3dprint
Eduardo_mtyDec 21, 2014#19
I live in México, And Now i stay in Orlando, Florida... For hollydays
joellThread starterPanama, Central America · Jan 6, 2015#20
This is the last chapter of this story,the part keeps the rubber in place and prevents ingress of water and dust, as installed ath the factory.

Picture lost · i61.tinypic.com

Now, I only need to glue (with 3M adhesive) the weatherstrip to be 100% sure no moisture gets inside.Lets see how this 3D printed part hold with the time, vibration, temperature, etc..