GogogordyOriginal postWinchester, Ca · Sep 28, 2014#1I will be ordering a TRD rear sway on my '11 LB, and the instructions I downloaded are a bit cryptic. Specifically the speak to backing out the shock bolt on one side but not the other.
Any install tips from those here who have installed these?
Im assuming TRD is the way to go.
Replies 22
CrankyOldManWest Michigan · Sep 28, 2014#2There's only one bolt that holds the shock to the rear beam. IIRC, the kit includes the second bolt. Basically, just jack up the rear of the car until the wheels are off the ground, get a pair of 14mm wrenches/sockets and go to town. Probably one of the easiest mods to do, but I've also done full suspension and gearbox swaps to date.
GogogordyThread starterWinchester, Ca · Sep 28, 2014#3My car is basicallt stock save for a TRD cat-back and wheels. Im hoping the rear sway bar just "tightens up" the handling a bit....Am I barking up the right tree? Downsides?
ExiwolfmanWasaga beach · Sep 28, 2014#4 Originally Posted by
Gogogordy ↑ My car is basicallt stock save for a TRD cat-back and wheels. Im hoping the rear sway bar just "tightens up" the handling a bit....Am I barking up the right tree? Downsides?
It's the best mod u can do for a Yaris , have it on mine and its night and day difference .
sent from my S4 on Mars
IllusionXBrossard, QC · Sep 29, 2014#5You back up the bolt but do not pull it out so you can slide the bar in and bolt it back together.
Anyways, it is pretty much self explanatory once you start installing it.
I did a short video when I installed the "Ultra Racing" one I purchased from Micro Image. It was less expensive and I am very happy with it. The TRD shouldn't be any different to install. Very easy install...
https://www.youtube.com/watch?v=8RKn7vV4fIo WeeYariGeorgetown, Ontario, Canada · Sep 29, 2014#7 Originally Posted by
Gogogordy ↑ I will be ordering a TRD rear sway on my '11 LB, and the instructions I downloaded are a bit cryptic. Specifically the speak to backing out the shock bolt on one side but not the other.
What the instructions are eluding to with that point is to loosen that bolt either from the nut side, or the head side. I can't remember which and don't know what difference it makes if you turn the head or the nut.
The first time I pulled that bolt was to install the TRD and I headed the instructions. Every time I've pulled the bolt since then I just go at it without caring which end I'm turning.
Sent from my iPhone using Tapatalk
IllusionXBrossard, QC · Sep 29, 2014#8 Originally Posted by
WeeYari ↑ What the instructions are eluding to with that point is to loosen that bolt either from the nut side, or the head side. I can't remember which and don't know what difference it makes if you turn the head or the nut.
The first time I pulled that bolt was to install the TRD and I headed the instructions. Every time I've pulled the bolt since then I just go at it without caring which end I'm turning.
Sent from my iPhone using Tapatalk
The impact gun only fits the bolt side anyways. So you would not be able to loosen the bolt side anyways.
WeeYariGeorgetown, Ontario, Canada · Sep 29, 2014#9Just pulled out my old instructions document. What I now believe the OP is unclear on is the following:
(b) Leave one bolt in place and back the other bolt out until flush with the shock mount.
Using left and right for example, what they are saying is remove the nut on the left side but do not move the bolt. Then on the right side, once nut is removed, slid the bolt back only to the point where it is flush with the mount. This then gives you the left side bolt to 'hang' the bar from while aligning the right side and pushing the bolt back into position.
sheekeebutMississauga, GTA, Toronto, ON · Sep 29, 2014#10Just a lesson I learned from my TRD. The nuts are swaged, so your final tightening and torquing will happen on bolt side, lest you want to gouge the metal finish underneath the nut, or worse, strip the nut's flats and still not have it torqued enough. That's why instructions emphasize that in bold, or caps, I forget which.
GogogordyThread starterWinchester, Ca · Sep 29, 2014#11 Originally Posted by
sheekeebut ↑ Just a lesson I learned from my TRD. The nuts are swaged, so your final tightening and torquing will happen on bolt side, lest you want to gouge the metal finish underneath the nut, or worse, strip the nut's flats and still not have it torqued enough. That's why instructions emphasize that in bold, or caps, I forget which.
Swaged?
WeeYariGeorgetown, Ontario, Canada · Sep 29, 2014#12 Originally Posted by
Gogogordy ↑ Swaged?
Locking ridges incorporated into the back side of the nuts.
sheekeebutMississauga, GTA, Toronto, ON · Sep 29, 2014#13One would then infer that the provided washers go on bolt side.
sheekeebutMississauga, GTA, Toronto, ON · Sep 29, 2014#14But by the time I realised all this, I'd tightened on the nut. Don't be dumb like me
GogogordyThread starterWinchester, Ca · Sep 29, 2014#15 Originally Posted by
sheekeebut ↑ But by the time I realised all this, I'd tightened on the nut. Don't be dumb like me
Haha, not dumb...just a trailblazer!
Thanks for the tips. I can do this....
My measure of success this way is typically based on how much blood I shed during the course of the project. Film at 11...
GogogordyThread starterWinchester, Ca · Oct 4, 2014#16Wow...wish I had done this a long time ago. Really composed over a variety of surfaces and conditions. No regrets.
Also put some sound deadening in the spare tire cavity and what a difference there as we'll.
Kar98DFW · Jan 2, 2015#17So because I'm a little bit lazy and didn't feel like crawling around the asphalt parking lot, I asked two places near my apartment how much they would charge to lift up my car, undo two bolts, put in the TRD sway bar, fasten four bolts, and put the lift back down. Sounds to me like 15 minutes at most. Both places said hour, hour and a half. JFC! In an hour, hour and a half, I am sure can do this myself laying in the dirt.
MUSKOKA800Chatham, Ontario, Canada · Jan 2, 2015#18 Originally Posted by
Gogogordy ↑ My car is basicallt stock save for a TRD cat-back and wheels. Im hoping the rear sway bar just "tightens up" the handling a bit....Am I barking up the right tree? Downsides?
No downside. And install is a no-brainer.
Toyota should have added it in manufacturing. Best bang for the buck you can do. Improved safety and 'put a smile on your face' handling improvement.
Kar98DFW · Jan 17, 2015#19 Originally Posted by
Kar98 ↑ So because I'm a little bit lazy and didn't feel like crawling around the asphalt parking lot, I asked two places near my apartment how much they would charge to lift up my car, undo two bolts, put in the TRD sway bar, fasten four bolts, and put the lift back down. Sounds to me like 15 minutes at most. Both places said hour, hour and a half. JFC! In an hour, hour and a half, I am sure can do this myself laying in the dirt.
I did it in 20 minutes in the parking lot.
jcboyAsia · Jan 23, 2015#20 Originally Posted by
Kar98 ↑ So because I'm a little bit lazy and didn't feel like crawling around the asphalt parking lot, I asked two places near my apartment how much they would charge to lift up my car, undo two bolts, put in the TRD sway bar, fasten four bolts, and put the lift back down. Sounds to me like 15 minutes at most. Both places said hour, hour and a half. JFC! In an hour, hour and a half, I am sure can do this myself laying in the dirt.
Haha. i've asked around for that too. apparently the cheapest way to do this is to put it in as an "alignment checkup" with results = no alignment needed. here it costs roughly $2.50 for that. pretty cheap for a lifter use. :)
ExiwolfmanWasaga beach · Jan 23, 2015#21 Originally Posted by
jcboy ↑ Haha. i've asked around for that too. apparently the cheapest way to do this is to put it in as an "alignment checkup" with results = no alignment needed. here it costs roughly $2.50 for that. pretty cheap for a lifter use. :)
Alignment check will still cost money most shop's will charge half hr shop rate and believe me will find something wrong to justify alignment lol
It calls for about 30 min to install done the right way problem may be with the lower shock nuts depending on ur region... Heat may have to be applied to remove had to do that to my car cos of winter's here.
jcboyAsia · Jan 23, 2015#22 Originally Posted by
Exiwolfman ↑ Alignment check will still cost money most shop's will charge half hr shop rate and believe me will find something wrong to justify alignment lol
oh...whoever said that going that "alignment" route was a good idea is a fool. LOL i meant we can all do it in our garage. LOL LOL 🤣
ExiwolfmanWasaga beach · Jan 23, 2015#23 Originally Posted by
jcboy ↑ oh...whoever said that going that "alignment" route was a good idea is a fool. LOL i meant we can all do it in our garage. LOL LOL 🤣
Agree with u 100% lol