Yarisworld Archive

Misc parts clearance sale - Making garage space for pellets

66 posts · 49,163 views · page 1 of 2

CTScottOriginal postUSA, CT · Aug 24, 2014#1
My 6 tons of wood pellets for winter heating are coming this week, so I need to clear off my pellet racks, which are currently loaded with car parts.

Prices including shipping are to continental US address. Shipping elsewhere quoted on request.

06-11 Liftback dash cup holder assembly: $7 shipped
Picture not included in this copy

06-08 Liftback Fog Light Hole Covers: $7 shipped per set (2 sets available)
Picture not included in this copy

06-11 OEM Radio Aux Jack: $20 Shipped
Picture not included in this copy

06-11 Liftback Rear Seat Base: $20 + shipping
The perfect base for making a completely flat rear cargo area or sleeping area (without drilling your original rear seat base or if you have 60/40 seats).
Picture not included in this copy

06-11 Liftback Front kick panel set: $12 shipped
Picture not included in this copy

Exhaust Manifolds: $5 Each + shipping
One has a plug in the O2 sensor hole and the other is without an O2 sensor.
Picture not included in this copy
Picture not included in this copy

06-11 Gas Filler Door Cable: $5 + shipping
Picture not included in this copy

06-11 Hood Latch Cable (2 available) $5 each + shipping
Picture not included in this copy

Replies 65

CrankyOldManWest Michigan · Aug 24, 2014#2
The mud flaps are tempting, but I'm concerned about drilling holes in the bodywork--Michigan uses salt on the roads.
sickpuppy1Kansas · Aug 24, 2014#3
Originally Posted by CrankyOldMan ↑
The mud flaps are tempting, but I'm concerned about drilling holes in the bodywork--Michigan uses salt on the roads.
clear silicone sealant on threads, or a can of undercoating sprayed on the inside( walmart or similar)
NEexpatS.E. New England · Aug 24, 2014#4
^Cranky,

It's been a while since I did mine, but if I remember correctly the front muds line with screws already there for the black wheel well plastic protector thing. On the rears you do drill/screw into the plastic rear bumber. I marked the holes, heated up a finish nail and melted pilot holes then screwed them in with and offset screwdriver, or you could remove the rears.

I don't recall drilling into any metal bodywork at all. Scott would know if my recollection is correct.
CTScottThread starterUSA, CT · Aug 24, 2014#5
Originally Posted by NEexpat ↑
^Cranky,

It's been a while since I did mine, but if I remember correctly the front muds line with screws already there for the black wheel well plastic protector thing. on the rears you do drill/screw into plastic. I marked the holes, heated up a finish nail and melted pilot holes then screwed them in with and offset screwdriver, or you could remove the rears.

I don't recall drilling into any metal bodywork at all. Scott would know if my recollection is correct.
The rears go completely into plastic. The fronts do require screwing into sheetmetal. The OEM ones do line up with the fender well holes. These do not.
ExiwolfmanWasaga beach · Aug 24, 2014#6
ok ..oil cap, horn and micro image pads ...i would like all that please , let me know with shipping to same address as last and same payment method :)
CrankyOldManWest Michigan · Aug 25, 2014#7
Originally Posted by CTScott ↑
The rears go completely into plastic. The fronts do require screwing into sheetmetal. The OEM ones do line up with the fender well holes. These do not.
Ok. I think I'll pass for now. Thanks anyway!
CTScottThread starterUSA, CT · Aug 25, 2014#8
Originally Posted by Exiwolfman ↑
ok ..oil cap, horn and micro image pads ...i would like all that please , let me know with shipping to same address as last and same payment method :)
PM sent
ExiwolfmanWasaga beach · Aug 25, 2014#9
Replied

sent from my S4 on Mars
fnkngrvIn The Hotbox · Aug 25, 2014#10
I will take that valve cover and the starter. hit me up on FB since you k ow the shipping drill. :)
CTScottThread starterUSA, CT · Aug 25, 2014#11
Originally Posted by fnkngrv ↑
I will take that valve cover and the starter. hit me up on FB since you k ow the shipping drill. :)
Will do.
AdriaanMontreal · Aug 25, 2014#12
pm sent.
CTScottThread starterUSA, CT · Aug 25, 2014#13
Added a few more parts
B2FiNiTYUS · Aug 25, 2014#14
nice garage
CTScottThread starterUSA, CT · Aug 26, 2014#15
More parts added
CTScottThread starterUSA, CT · Aug 29, 2014#16
Added brake caliper set and removed bumper, which sold.
ExiwolfmanWasaga beach · Aug 29, 2014#17
Calipers ....shipped can you let me know ...tx

sent from my S4 on Mars
ExiwolfmanWasaga beach · Aug 29, 2014#18
And are the calipers OEM Toyota? Parts

sent from my S4 on Mars
CTScottThread starterUSA, CT · Aug 29, 2014#19
Originally Posted by Exiwolfman ↑
And are the calipers OEM Toyota? Parts

sent from my S4 on Mars
Calipers are OEM. It looks like shipping to Canada would be $56. They are way heavier than I would have imagined. Calipers and frames weigh a total of 18.6 lbs.
ExiwolfmanWasaga beach · Aug 29, 2014#20
Originally Posted by CTScott ↑
Calipers are OEM. It looks like shipping to Canada would be $56. They are way heavier than I would have imagined. Calipers and frames weigh a total of 18.6 lbs.
U got pm
Originally Posted by Exiwolfman ↑
And are the calipers OEM Toyota? Parts

sent from my S4 on Mars

sent from my S4 on Mars
CTScottThread starterUSA, CT · Aug 29, 2014#21
Calipers are sold.
CTScottThread starterUSA, CT · Sep 1, 2014#22
Power mirror switch sold.
ExiwolfmanWasaga beach · Sep 4, 2014#23
Parts arrived ....ty Scott specially for the horn did not know that its an air horn lol its going to be cool making ppl jump .
PS my girlfriend maybe not to happy with the idea ...lmao

sent from my S4 on Mars
CTScottThread starterUSA, CT · Sep 4, 2014#24
Originally Posted by Exiwolfman ↑
Parts arrived ....ty Scott specially for the horn did not know that its an air horn lol its going to be cool making ppl jump .
PS my girlfriend maybe not to happy with the idea ...lmao

sent from my S4 on Mars
LOL. It's not quite as loud as it looks.
ExiwolfmanWasaga beach · Sep 4, 2014#25
Think ,hope its as loud as a truck horn lol
Now to wire it ,should I do direct ..one wire from horn and ground it or go through horn realay

sent from my S4 on Mars
CTScottThread starterUSA, CT · Sep 4, 2014#26
Originally Posted by Exiwolfman ↑
Think ,hope its as loud as a truck horn lol
Now to wire it ,should I do direct ..one wire from horn and ground it or go through horn realay

sent from my S4 on Mars
I would add a relay. You could try a quick test with the OEM wiring and see if the horn fuse blows. The Wolo instructions do not say what the horn actually draws, but it does say to fuse it at 20 Amps, sit is is likely over 10A.

http://www.wolo-mfg.com/419%20english.pdf
ExiwolfmanWasaga beach · Sep 4, 2014#27
That is what I thought wonder if just replacing the fuse would be OK and the harnest could handle the extra courent

sent from my S4 on Mars
CTScottThread starterUSA, CT · Sep 4, 2014#28
Originally Posted by Exiwolfman ↑
That is what I thought wonder if just replacing the fuse would be OK and the harnest could handle the extra courent

sent from my S4 on Mars
Considering that the horn is typically used in short bursts, that would probably be OK. Quite a few people have installed dual horn kits without using a relay.
ExiwolfmanWasaga beach · Sep 4, 2014#29
OK ty ...gone try with stock setup first but think to be safe run a relay ..found your old post on that on how to make it all work on the "stebel nautilus horn"

sent from my S4 on Mars
CTScottThread starterUSA, CT · Sep 5, 2014#30
Mudflaps are sold.
07stlYarisSTL · Sep 9, 2014#31
Got the flaps yesterday. Will install this weekend. Thanks again Scott.
nobodywiseCayman · Sep 11, 2014#32
Hey Scott! Can the engine cover fit a 2007 sedan 2nz-fe? I'm interested
CTScottThread starterUSA, CT · Sep 11, 2014#33
Originally Posted by nobodywise ↑
Hey Scott! Can the engine cover fit a 2007 sedan 2nz-fe? I'm interested
I believe it will. The 1.3L 2NZ and 1.5L 1NZ share the same valve cover.
CTScottThread starterUSA, CT · Sep 18, 2014#34
Engine cover is sold.
nobodywiseCayman · Oct 5, 2014#35
Originally Posted by CTScott ↑
Engine cover is sold.
Engine cover fit perfectly! Just need to get my engine bay cleaned up a bit and I'll bolt it up!

Thanks again!
Picture not included in this copy

I love the back of my car, the front... not so much
TommyYarisCalgary, AB · Oct 21, 2014#36
Any chance the Front Hubs/Assemblies will fit in an 09 HB? No ABS.
CTScottThread starterUSA, CT · Oct 22, 2014#37
Originally Posted by TommyYaris ↑
Any chance the Front Hubs/Assemblies will fit in an 09 HB? No ABS.
Yes they would fit an 09. How do you not have ABS on your 09?
BIGTAZ351North Branch, MN · Dec 21, 2014#38
I had an evil thought with that hood, I always thought about putting Rally Lights on my hood but don't enjoy the fact that they would permanently leave holes in the hood....I used to work 2:30-11 and wish I had 4 KC Deer-lighters, my wife now drives it at night (3-11) hmmmn......
CTScottThread starterUSA, CT · Dec 21, 2014#39
Originally Posted by BIGTAZ351 ↑
I had an evil thought with that hood, I always thought about putting Rally Lights on my hood but don't enjoy the fact that they would permanently leave holes in the hood....I used to work 2:30-11 and wish I had 4 KC Deer-lighters, my wife now drives it at night (3-11) hmmmn......
You need a setup like the Tag Rally Sport Yaris:
Picture not included in this copy
BIGTAZ351North Branch, MN · Dec 21, 2014#40
OH HELL YEAH!!!!!!!!!!!!!!
I just sent that to my wife on FB....
She likes it!
CTScottThread starterUSA, CT · Dec 21, 2014#41
Originally Posted by BIGTAZ351 ↑
OH HELL YEAH!!!!!!!!!!!!!!
I just sent that to my wife on FB....
She likes it!
That's actually a custom light pod that TRS had made. It bolts to the hood and they have it set up where it can easily be removed for races where they don't need it.
BIGTAZ351North Branch, MN · Dec 21, 2014#42
I wish it was mass-Produced w/Hella Lights, I would seriously consider putting it on...
I have an 2004 F150 and Hella discontinued their Rally 4000 F150 Grille right before I discovered it....no more to be had... :(
3cyltrboOttawa · Dec 28, 2014#43
assume the stuff still pictured is still for sale?

if so, how about a combo price / shipped to 13669 for the rear seat base/console and kick panels?

Cheers

Will
CTScottThread starterUSA, CT · Dec 28, 2014#44
Originally Posted by 3cyltrbo ↑
assume the stuff still pictured is still for sale?

if so, how about a combo price / shipped to 13669 for the rear seat base/console and kick panels?

Cheers

Will
Yes. Let me get a weight and measurement on the base and I'll PM you a shipping cost.
invader166Langley, BC · Mar 30, 2015#45
I have 2 questions:

1. Do you still have the dome light posted in the first page? The one I currently have has a loose swich that no longer switches on/off/door without me pushing upward on the switch itself. (not sure if that's a common problem or not)

2. Do you ship to canada? I'll pay for extra shipping.😁
CTScottThread starterUSA, CT · Mar 30, 2015#46
Originally Posted by invader166 ↑
I have 2 questions:

1. Do you still have the dome light posted in the first page? The one I currently have has a loose swich that no longer switches on/off/door without me pushing upward on the switch itself. (not sure if that's a common problem or not)

2. Do you ship to canada? I'll pay for extra shipping.😁
I do have the dome light assembly, but it is just the plastic housing with the lever, not the actual light assembly above it (as that was part of the harness)
invader166Langley, BC · Mar 30, 2015#47
Originally Posted by CTScott ↑
I do have the dome light assembly, but it is just the plastic housing with the lever, not the actual light assembly above it (as that was part of the harness)
That's perfect! The plastic housing is all I need!
badverbUnionville · Apr 15, 2015#48
I need to replace a damaged spring on my 2007 liftback. Do you have the springs for sale?
CTScottThread starterUSA, CT · Apr 15, 2015#49
Originally Posted by badverb ↑
I need to replace a damaged spring on my 2007 liftback. Do you have the springs for sale?

I just have a set of fronts on hand.
TommyYarisCalgary, AB · Apr 15, 2015#50
Originally Posted by CTScott ↑
Yes they would fit an 09. How do you not have ABS on your 09?
Canadian model? I have no ABS or Traction control in my 09 LB.