Yarisworld Archive

Anyone replace their oil drain plug with one of these?

13 posts · 6,728 views

SilverkarnOriginal postUnited States · May 14, 2014#1
http://www.qwikvalve.com/

I just read about this on some blog, anyone use one? Any problems? I think this would be great if you change your own oil. And if you decide you don't want to change your own oil once in a while just bring the plastic bit and the hose with you to the oil change place.

So. How long have you had it on your car? And have you had any problems with it?

Replies 12

CTScottUSA, CT · May 14, 2014#2
Yes. I have Fumoto quick valves on all of my vehicles. The oldest one I have had on for over 5 years without issue. If you are lowered, you need to be careful as the valve hangs lower than the drain bolt head would have.
schumePNW · May 14, 2014#3
I put these on every car I own at my first oil change. Sometimes the lever might not be oriented exactly the way you want, but I've never had any leaks or issues. Well built units.
SilverkarnThread starterUnited States · May 14, 2014#4
Originally Posted by CTScott ↑
Yes. I have Fumoto quick valves on all of my vehicles. The oldest one I have had on for over 5 years without issue. If you are lowered, you need to be careful as the valve hangs lower than the drain bolt head would have.
Car is stock height. They have one that is made for cars that have been lowered. I'll probably end up getting that one as i do go over speed bumps quite often.
MyzticZ3r0Las Vegas, NV · May 14, 2014#5
I got one a couple years ago and I had the unfortunately luck of the valve stripping my oil pan and leaked oil. I'm a small percentage of this happening, but thought I'd let you know it does.
marauderNKY · May 14, 2014#6
Originally Posted by CTScott ↑
Yes. I have Fumoto quick valves on all of my vehicles. The oldest one I have had on for over 5 years without issue. If you are lowered, you need to be careful as the valve hangs lower than the drain bolt head would have.
Yep, tried this on my RX-8 and had the same problem. The adapter needed to fit the valve on my vehicle caused the final location of the drain valve tab to be the lowest point of the car and facing the rear of the vehicle. Any minor hit would open the valve. I was told to add washers to adjust the final position, the problem was I needed to clear almost 90 degrees of rotation.

They do recommend you install the safety spring just in case, which I would highly recommend because it also keeps some punk from draining your oil easily should they be crawling around underneath your car for whatever reason.

The valve adapter and safety spring I bought for my RX-8 is still new in the box. I'd give mine to you but it looks like the drain plug size is not the same.
jack blacksoutheast USA · May 14, 2014#7
I just replaced with one of these:
Picture lost · img19.imageshack.us

Monitoring engine wear without paying for UOA.
SilverkarnThread starterUnited States · May 15, 2014#8
Originally Posted by jack black ↑
I just replaced with one of these:


Monitoring engine wear without paying for UOA.

What is that?
marauderNKY · May 15, 2014#9
Looks like a magnetic drain plug to me.
IllusionXBrossard, QC · May 15, 2014#10
It's a goldplug. http://www.goldplug.com/

i have one of those in mine. There are fine metal particles on the plug each time i change oil...
nortonfbmotown · May 15, 2014#11
I have been using those for a long time. Some cars seem to always have a
little bits attracted.
Cheap insurance, if you change your oil.
Steve
monchito18Puerto Rico, Isabela · May 15, 2014#12
I can't have that here, car scrapes everywhere :(
UberSilverAlameda,Ca. · May 16, 2014#13
Got them on my Bike and Land Cruiser, but I don't like the location for the yaris, so I past. Plus I change my oil once per year, so it's not all that needed in my case.