Yarisworld Archive

at what point do the stock rods/pistons fail?

29 posts · 10,022 views

TidOriginal postUnited States · Mar 27, 2014#1
so im looking to buy a yaris and turbo it (i have built 3 neon engines from the ground up for boost and put together a sealed itb turbo intake motor with a efr 7064 turbo pushing 450whp on e85and self tuned it so i know a thing or two but looking for a newer platform)
any way now to my question
at what horse power/ tq point do the stock rods or pistons ring lands fail on these motors?
thanks
Taylor

Replies 28

fnkngrvIn The Hotbox · Mar 27, 2014#2
that is a loaded question to be honest. there isn't necessarily a cut and dry answer because there are a LOT of variables. The rule of thumb however on the 1nz has been proven to be for the most part around 8psi for longevity and you can 10psi with the right tune and correct fuel setup, etc. There are supposedly however people down in PR that say they are running 12-16psi on stock internals. I am kind of at a loss honestly on that one. I blew 2 rods but my wastegate stuck on me. We had another previous member who went around 4 months at 12psi and then came out on a crisp, cool fall morning only to get a couple blocks and have a rod bend.

I am currently running 200/190+ hp/tq on my setup on pump gas. I hit 220/210 on VP100.

Welcome to the forum. Your best bet would be to do a search in the Forced Induction section. Over the last 7+ years we have had a lot of discovery. Feel free as well to shoot me a PM if you wish to discuss my experiences. 🎉
TidThread starterUnited States · Mar 28, 2014#3
from my digging around here with a solid tune the rods fail at approx 200-190whp/tq
now what is the min for a built block rods ,pistons, head studs,

now who makes the cheapest forged rods and pistons (no being cheap just on a budget)
fnkngrvIn The Hotbox · Mar 28, 2014#4
Oh I know you're not trying to be cheap everybody has to be on a budget and if I had any sense at all I would be on one too...lol

Sent from my SCH-I545 using Tapatalk
kounj · Mar 28, 2014#5
Molnar rods would be the cheapest I would use. I am running @10psi on a stock block.
TidThread starterUnited States · Mar 28, 2014#6
please dont refer to psi withought stating the turbo your running cause psi is independent of horsepower and tq
also im
and does anyone else beside aria and cp make pistons for the 1nz-fe i googled but couldnt find any
BEEFnorth carolina · Mar 28, 2014#7
a lot of guys use microimageonline.com around here for their forged internals.

you may want to check them out.
TidThread starterUnited States · Mar 28, 2014#8
Originally Posted by BEEF ↑
a lot of guys use microimageonline.com around here for their forged internals.

you may want to check them out.
i have been there i have only seen the pauter rods on their site its not very user friendly.
TidThread starterUnited States · Mar 28, 2014#9
dezod looks to have the best budget options
molnar rods $395 and cp pistons $599 which beats TBR by like $100
or i can go with BC sportsman rods for $417 even if they only can take 100hp per cyl thats a big safty margin from what im looking to get out what im planing to build. im thinking 300whp will be scary enough for my blood,
kounj · Mar 28, 2014#12
Sorry, I am running a TDO4H-15G-6
TidThread starterUnited States · Mar 28, 2014#13
yeah im looking to run a bw efr 6256 which is kind of an awesome setup if you have ever looked at them wg bov all are intergrated into the turbo
Bluevitz-rsOshawa, Ontario, Canada · Apr 2, 2014#14
The EFR does look like a really good efficient turbo
YodaFL · Apr 3, 2014#15
12 psi with a t25 and you will start to have problems.
cali yarisCanoga Park, CA · Apr 4, 2014#16
I can compete with Dezod, or anyone. I personally wouldn't use Molnar rods, but it is a less expensive option.

I'm actually shipping off a set of CP pistons and Carillo rods today. 👍
NT05usa · Apr 7, 2014#17
what seems to be the issue with the Molnar Rods? They appear to be of good quality and on a engine like this I see no real difference between them or Carillo. What kills me is you can buy a v8 set from Crower and still pay the same price for a 4cyl set.
fnkngrvIn The Hotbox · Apr 7, 2014#18
I would assume it is supply and demand. There is a lot more demand for v8 rods and pistons.

From my m-o-b-i-l-e. Land Speed with a Yaris filled with AMSOIL lubricants as a T-1 Certified Dealer.
NT05usa · Apr 7, 2014#19
That's my point. I don't believe the Molnar rods are any less of a rod than Carillo. It seems to me the owner of Molnar just keeps things in better perspective.
cali yarisCanoga Park, CA · Apr 15, 2014#20
I don't believe the Molnar rods are any less of a rod than Carillo.
Did you use them in your build?
yariSB86OH · Apr 16, 2014#21
I'm seeing 8-10 psi from my td04. On stock internals. Been going strong for almost a year now.
xnamerxxso cal · Apr 22, 2014#22
Out of curiosity does anyone have the weights of the stock pistons compared to the aftermarket options? All of the aftermarket pistons appear to be quite heavy compared to the stock ones.
fnkngrvIn The Hotbox · Apr 22, 2014#23
Originally Posted by xnamerxx ↑
Out of curiosity does anyone have the weights of the stock pistons compared to the aftermarket options? All of the aftermarket pistons appear to be quite heavy compared to the stock ones.
That is an interesting question indeed. I can ballpark the stock weight prolly next week once I get my crank back. I would suppose aftermarket will dependent upon design (I or H beam) and manufacturer.

sent from my m-o-b-i-l-e
xnamerxxso cal · Apr 22, 2014#24
I'm not so concerned about the rod weights since I'm not allowed to change those under the rules anyway, and there is very little to gain, but the pistons I'm very interested in.
fnkngrvIn The Hotbox · Apr 22, 2014#25
Originally Posted by xnamerxx ↑
I'm not so concerned about the rod weights since I'm not allowed to change those under the rules anyway, and there is very little to gain, but the pistons I'm very interested in.
Oh crud...missed that sorry. I don't have any way to hook you up with just the piston weight. I really don't want to take this apart since it has twisted (pardon the pun) sentimental value.

Picture not included in this copy

sent from my m-o-b-i-l-e
xnamerxxso cal · Apr 22, 2014#26
Is the stock rod bushed?
Paris vvt-iAthens · Apr 26, 2014#27
Originally Posted by yariSB86 ↑
I'm seeing 8-10 psi from my td04. On stock internals. Been going strong for almost a year now.
How much horsepower/torque are you making and how usually do you floor the pedal? thats very important.

By the way here in greece we have 2 1nzfes working on 150whp/ 19wkgm for over 4 years with mild/agressive driving without issues
yariSB86OH · Apr 27, 2014#28
I haven't dynoed my car yet. they say the td04 gives an extra 100 hp. i drive aggressively when i need to.
kounj · Apr 27, 2014#29
Originally Posted by xnamerxx ↑
I'm not so concerned about the rod weights since I'm not allowed to change those under the rules anyway, and there is very little to gain, but the pistons I'm very interested in.
Cp piston 9:1 data sheet say they are 235grams