Yarisworld Archive

blitz supercharger problem

15 posts · 4,749 views

Black_griffin6Original postAtlanta Georgia · Mar 16, 2014#1
Hey guys, I recently bought a used blitz supercharger kit. I have it all wired up and ready to go, and I can't get the clutch on the compressor to engage. I even tried bypassing the switch and hooking a 12 volt connection directly to it and it doesn't engage.
Help? XD

Replies 14

Black_griffin6Thread starterAtlanta Georgia · Mar 16, 2014#2
Can the clutch go bad? Do I need to replace it?
CTScottUSA, CT · Mar 16, 2014#3
Measure the resistance between the two clutch wires. If it reads as open, then the solenoid within the clutch is bad.
Black_griffin6Thread starterAtlanta Georgia · Mar 17, 2014#4
Alright. So if it is bad, what are my options in terms of fixing it?
47_MasoN_47Northwest Alabama · Mar 17, 2014#5
I've heard Blitz USA's customer support is pretty bad. Maybe look into just switching it for a fixed pulley?
Black_griffin6Thread starterAtlanta Georgia · Mar 17, 2014#6
That might be an option. I've been looking for one just in case. Although I would like to stay around safe boost levels because I'm only on stock internals.
Do you know where I can get one?
CTScottUSA, CT · Mar 17, 2014#7
Check with Micro Image as well. Garm seems to have somewhat of a spare Blitz parts supply.
Black_griffin6Thread starterAtlanta Georgia · Mar 18, 2014#8
Alright, I'll check with Garm too.
So if I get a fixed pulley can I just bolt it onto the supercharger?
CTScottUSA, CT · Mar 18, 2014#9
Originally Posted by Black_griffin6 ↑
Alright, I'll check with Garm too.
So if I get a fixed pulley can I just bolt it onto the supercharger?
Yes - In place of the clutch pulley assembly.

At that point you will no longer use the Blitz fuel controller though. You will need to go with another form of fuel management.

You could also modify the existing clutched pulley to make it fixed.
Black_griffin6Thread starterAtlanta Georgia · Mar 18, 2014#10
Originally Posted by CTScott ↑
Yes - In place of the clutch pulley assembly.

At that point you will no longer use the Blitz fuel controller though. You will need to go with another form of fuel management.

You could also modify the existing clutched pulley to make it fixed.
I have the Aem F/IC hooked up, but it's not currently on. I'm using the bypass wire.
When I tried to start the car after the installation of the supercharger, I had the FIC hooked up and it wouldn't start, not sure what the map is on there since it's a used unit.

Do you think the Aem piggyback would work?
How could I mod the current clutch pulley to be fixed?
CTScottUSA, CT · Mar 18, 2014#11
Originally Posted by Black_griffin6 ↑
I have the Aem F/IC hooked up, but it's not currently on. I'm using the bypass wire.
When I tried to start the car after the installation of the supercharger, I had the FIC hooked up and it wouldn't start, not sure what the map is on there since it's a used unit.

Do you think the Aem piggyback would work?
How could I mod the current clutch pulley to be fixed?
The F/IC would be fine for tuning it.

For converting the bad clutch to fixed, the simplest way to do so would be to weld the two sides together.
Black_griffin6Thread starterAtlanta Georgia · Mar 18, 2014#12
Originally Posted by CTScott ↑
The F/IC would be fine for tuning it.

For converting the bad clutch to fixed, the simplest way to do so would be to weld the two sides together.
Okay, excellent.
Would I need a waste gate or blow off valve?
CTScottUSA, CT · Mar 18, 2014#13
Originally Posted by Black_griffin6 ↑
Okay, excellent.
Would I need a waste gate or blow off valve?
No. The clutch does not disengage to allow the unit to blow off, so it seems to be internally limited, or perhaps limited by RPM.

I did see someone with an underdrive pulley mention producing more than the 6psi that mine tops out at.
Black_griffin6Thread starterAtlanta Georgia · Mar 19, 2014#14
so it appears that the solenoid my clutch is bad. Do you have a diagram of what the clutch looks like so I may attempt to weld it?
It's currently still on car, so I'm trying to avoid taking the supercharger off the car again due to it being kind of a hassle to do so.
CTScottUSA, CT · Mar 19, 2014#15
Originally Posted by Black_griffin6 ↑
so it appears that the solenoid my clutch is bad. Do you have a diagram of what the clutch looks like so I may attempt to weld it?
It's currently still on car, so I'm trying to avoid taking the supercharger off the car again due to it being kind of a hassle to do so.
The picture below shows the pulley. The outermost plate rotates freely if you try while the engine is off. You would need to weld it to the actual pulley (with the belt groove) to make it become fixed.



Picture not included in this copy