Yarisworld Archive

ZPIracing Turbo Pistons

22 posts · 14,049 views

ZPIracingOriginal postLouisville, KY · May 11, 2007#1
I know a lot of you guys want the added security of turbo pistons. The ZPIracing turbo pistons is the only piston you can get with Total Seal rings. Nothing but the best from ZPIracing.

http://www.zpiracing.net/store/produ...roducts_id=347

Replies 21

CASTREXCosta Rica · May 11, 2007#2
$3000 Turbo kit
$600 Pistons
$500 race clutch
$200 Exhaust


I'm going right now to buy some lottery!
DragonaccAtl, GA · May 11, 2007#3
How are the rods on the 1nz? If changing pistons it usually makes sense to toss in new rods at the same time.
ZPIracingThread starterLouisville, KY · May 11, 2007#4
Stock rods have been holding up well, we are working on them. We will have some race bearings out soon with engine packages.
dngzvancouver · May 11, 2007#5
wont the engine internals of the xb work with our yarii??
nebulightPA · May 11, 2007#6
Originally Posted by Dragonacc ↑
How are the rods on the 1nz? If changing pistons it usually makes sense to toss in new rods at the same time.
If the stock pistons are going before the rods, then I'd say somethings wrong with the tune.

Who manufactures the pistons?
ChinoCharlesOH · May 11, 2007#7
From what I hear, rods go first on the 1NZ... along with the axles. Feel free to confirm or deny.
dngzvancouver · May 12, 2007#8
we want rods!
spkrman2 · May 12, 2007#9
Originally Posted by dngz ↑
we want rods!

Picture not included in this copy
dngzvancouver · May 12, 2007#10
what kinda rods are those?!! eeeww
SabretoothSt Cloud FL · May 12, 2007#11
Not paying any amount for those rods...
Turbo Rods, might be an add on when I go lotto!
sam07yarisTiverton, RI · May 12, 2007#12
Originally Posted by spkrman ↑
Picture not included in this copy
.............................WTF!!!!!!!!!!!!!.. HAHA
joey1320Lakewood, Ohio · May 12, 2007#13
rods should definitely come before pistons. no ?s about that!!!
who makes the pistons?


do you guys sell the e-manage pretuned for the yaris?
can i get that?
ZPIracingThread starterLouisville, KY · May 14, 2007#14
all ZPI pistons are made by CP. We will have rods out very soon.
nebulightPA · May 14, 2007#15
Originally Posted by ZPIracing ↑
all ZPI pistons are made by CP. We will have rods out very soon.
👏 CP makes some of the best pistons around! 👍
spkrman2 · May 15, 2007#16
Would it make sense for me to pick these up?
nebulightPA · May 15, 2007#17
Originally Posted by spkrman ↑
Would it make sense for me to pick these up?
No, not with your power levels. You'd snap a rod before you'd melt a piston. In most applications, you can usually double your stock HP and be fine on stock internals...but if it's a honda, you can quadruple your stock HP ;)
Doc ZaiusOttawa, ON, Canada · May 15, 2007#18
I'm sure there are some Toyota engines that'll take crazy amounts of power. The problem with boosting the NZ1-FE is the offset crank design... puts a lot of side-loading pressure on the rod. But its supposed to be a more fuel efficient design...!

I'd say wait for new rods! (IMVHO) 😁
spkrman2 · May 15, 2007#19
Yea i think rods would make more sense at this point... but of course, if I was to open her up I'd probably do it all at once.
nebulightPA · May 15, 2007#20
Originally Posted by spkrman ↑
Yea i think rods would make more sense at this point... but of course, if I was to open her up I'd probably do it all at once.
Smart move. My thought, if you are going to build a motor, do the whole thing.
VanderkittenBerkeley, CA · May 29, 2007#21
The thing I've seen that snaps rods is higher RPMS more so than 50HP on a stock motor. Figure the increase of 100 HP is 25hp per cylinder, about what a 150cc Honda CRF150R makes with a rod the size of a spoon. high RPM's will increase piston speed, and it's the point at which the piston stops traveling upward that the rod recieves the greatest stress.

I think this is why a lot of guys like the Supercharger idea, because your operating RPMs do not change drastically. I think leaving the rev-limiter stock, or within a couple hundred RPM's of the stock set-up would help against snapage. I could be talking out my a$$ thoguh, I am a motorcycle guy, and we deal with redlines in the 16,000 range. =) I know cars are more sensitive.

D
blacksanVirginia · May 29, 2007#22
Originally Posted by Vanderkitten ↑
I am a motorcycle guy, and we deal with redlines in the 16,000 range. =) I know cars are more sensitive.D
How about 19,000 range that F1 cars operate in.😲