Yarisworld Archive

Blitz NuR Spec Exhaust Review (07 Liftback)

49 posts · 14,318 views

Ran KizamaOriginal postCanton, GA · May 7, 2007#1
Got in the exhaust today at work. I've got finals at 5:45 and then I'm off to my friend's house to put the exhaust on. I gotta admit that the promotion pictures are misleading. I expected a one-piece canister/tip like you see on most cars, but ours is designed similar to the Fujitsubo. The "installation kit" also only included two nuts and an O-Ring for the mounting point. I guess you don't need much for an axle-back. 😛 Anyway, here are some pics to entertain you until I get it on and get a video/sound clip.

The whole thing...
Picture not included in this copy

My arm in the exhaust tip...
Picture not included in this copy

Rear View
Picture not included in this copy

Quarter View
Picture not included in this copy

Close Up
Picture not included in this copy

The Burn (BUY NEW HANGERS BEFORE INSTALLING)
Picture not included in this copy

Initial results are in after an install, outside hearing, inside hearing with both windows up and down, and a highway acceleration test.

Install
Takes about 10mins. If the install takes you more than 15-20mins, you're retarded. The exhaust fitment is good, but you will need longer hangers. Go ahead and buy these in advance. Right now, my muffler tip sits on the bottom of my rear bumper and has smoldered the bottom of it thru the paint. That's about it for the install. Very simple.

Sound
VERY QUIET. I was very surprised. During idle, the car is almost stock aside from a slight pulsing sound. Sounds kinda cool, but not loud at all. During regular cruising speeds, the exhaust is mellow and deep, but not loud in any sense. The tone is louder during a good downrev than it is when accelerating. Upon hard acceleration, the tone last a few seconds but then the Fujita intake drowns it out. Sounds about the same outside the car as well. I had a buddy do a driveby, and the car doesn't really have an exhaust tone, just a loud growl from the intake.

Replies 48

5spBlazerFlorida · May 7, 2007#2
thats a big can.
Ran KizamaThread starterCanton, GA · May 7, 2007#3
True, but judging the way that the exhaust is mounted and such, you shouldn't be able to see most of it from behind. I don't think...maybe...
R0ME0Seattle, WA · May 7, 2007#4
can't wait to hear sound clips
but i was really hoping it'd be a canister too! Hopefully the sound makes up for it!
501oregon · May 7, 2007#5
thats fookin sexy. if my car doesnt sell that might be just what the doctor ordered.

who did you get it from? was it a good price? well i dont care as much about the price other than that is a quality peice.

hope it sounds good you lucky bastid
YarisGuyUSA · May 7, 2007#6
That thing is beautiful 🤤

brickhardmeatInner City, Dallas · May 7, 2007#7
He is fisting his exhaust! eww
BlenjarCT · May 7, 2007#8
nice!~!

-- Blen
PetersRedYarisThe Black Hills of South Dakota · May 7, 2007#9
Look's like it's made very well. Oh wait, everything looks well made when comparing it to the ZPI exhaust. 🙄 Actually I really like it, the Blitz, not the ZPI.
ZeeksRsBlastCanada · May 7, 2007#10
I wan't the same one... now I really wan't to order now!🙇
Ran KizamaThread starterCanton, GA · May 7, 2007#11
Initial results are in after an install, outside hearing, inside hearing with both windows up and down, and a highway acceleration test.

Install
Takes about 10mins. If the install takes you more than 15-20mins, you're retarded. The exhaust fitment is good, but you will need longer hangers. Go ahead and buy these in advance. Right now, my muffler tip sits on the bottom of my rear bumper and has smoldered the bottom of it thru the paint. That's about it for the install. Very simple.

Sound
VERY QUIET. I was very surprised. During idle, the car is almost stock aside from a slight pulsing sound. Sounds kinda cool, but not loud at all. During regular cruising speeds, the exhaust is mellow and deep, but not loud in any sense. The tone during a good downrev are louder than accelerating. Upon hard acceleration, the tone last a few seconds but then the Fujita intake drowns it out with a loud growl. Sounds about the same outside the car as well. I had a buddy do a driveby, and the car doesn't really have a tone, just a loud growl.

I'll try to get some vids tomorrow and add them to the first post. (^_^)
yrsdrgnSF,CA · May 8, 2007#12
That looks pretty cool. I wonder how it compares to the Tanabe Concept G axle back exhaust in sound
CASTREXCosta Rica · May 8, 2007#13
Installed pics??????????????????????????😕
Ran KizamaThread starterCanton, GA · May 8, 2007#14
Originally Posted by CASTREX ↑
Installed pics??????????????????????????😕
I should have some this afternoon (7PM EST) once I get the longer hangers on it. 👍
wahLA, CA · May 8, 2007#15
Beautiful exhaust! 👍

I know this is going to sound nuts, but do you guys think performance would be effected if someone were to lose the tip for a more "sleeper" look?

Can't wait to hear this thing
Ran KizamaThread starterCanton, GA · May 8, 2007#16
Originally Posted by wah ↑
Beautiful exhaust! 👍

I know this is going to sound nuts, but do you guys think performance would be effected if someone were to lose the tip for a more "sleeper" look?

Can't wait to hear this thing
I don't think ditching the tip will affect the performance as all. The primary thing you need to look for is the piping structure and the breathability of the muffler. To be honest, there's not a lot of room back there to really hide a muffler unless you have a rear skirt/body kit. Even with as high as the Blitz and Tanabe exhausts sit, you can still see them from behind the car. 🙂
wahLA, CA · May 8, 2007#17
Thanks, that's what I figured. Didn't know if the tip worked as some sort of voodoo harmonic diffuser. I think this one of these higher sitting setups in a grey or black ceramic coat might de just sleepy enough for my taste.
Chris07LBNew Jersey · May 8, 2007#18
Ran, 🙇 🙇

Can wait to see the installed pics!!!

Looks like an exhaust for me... tired of all these other fart can sounding 'backs.
Vic-2NZFEPanama · May 8, 2007#19
nice exhaust! need pics of the installation and price azap pleaze 😁
Ran KizamaThread starterCanton, GA · May 8, 2007#20
Got a good deal from iptuned.com, a site sponsor. Hit them up for a deal. 🙂

Pics are coming guys, be patient. lol
Ran KizamaThread starterCanton, GA · May 9, 2007#21
Pics added to first post. (^_^)d
Doc ZaiusOttawa, ON, Canada · May 9, 2007#22
Nice burn! Ouch!!

What did you use for longer rubber hangers? Did you replace both hangers on the muffler?
Ran KizamaThread starterCanton, GA · May 9, 2007#23
No, I just got a longer hanger from AutoZone for the very rear hanger. Lowered it about 1/2 an inch. Just enough.
nqdBoston, MA · May 9, 2007#24
did you have to re-weld?
Doc ZaiusOttawa, ON, Canada · May 9, 2007#25
Originally Posted by Ran Kizama ↑
No, I just got a longer hanger from AutoZone for the very rear hanger. Lowered it about 1/2 an inch. Just enough.
Dammit. I got the JDM TRD muffler sitting in a box waiting to be installed. Everybody else on the board simply bought a 89 Civic rubber hanger for the very rear, and it hung fine. Mine still contacts the bumper for some reason!! (Maybe I have a droopy bumper?? 😛) Any larger-sized hanger has holes that are too large! I'm going to have to take it to a shop and get a longer metal hanger bracket welded on! 🙁
PetersRedYarisThe Black Hills of South Dakota · May 9, 2007#26
Originally Posted by Ran Kizama ↑
No, I just got a longer hanger from AutoZone for the very rear hanger. Lowered it about 1/2 an inch. Just enough.
A new exhaust shouldn't need a longer hanger. By looking at your first picture it appears the rear hanger is bent down about 1/2 inch, perhaps damaged in shipping. Maybe that's the problem?? 🤷 I just noticed it looked bent and wondered.

I want this exhaust now!!! Damn you Ran, I don't have the money.
Ran KizamaThread starterCanton, GA · May 9, 2007#27
Originally Posted by PetersRedYaris ↑
A new exhaust shouldn't need a longer hanger. By looking at your first picture it appears the rear hanger is bent down about 1/2 inch, perhaps damaged in shipping. Maybe that's the problem?? 🤷 I just noticed it looked bent and wondered.
Probable, but it's a pretty heavy duty hanger and not very easy to bend. The packaging was also undamaged so who knows? 🤷 I do recall that somebody else on here had to get longer hangers for their Tanabe exhaust I think.

Originally Posted by ToTo ↑
Any video/sound clips or driveby clips yet?
Not yet. Hopefully my buddy will bring me the camera tomorrow. I'll be busy thru Saturday with birthday parties and Formula D, but I should have time to record and post on Sunday. 🙂
GalavoxxSan Francisco · May 9, 2007#28
My only issue is with the size of the tip. That thing is huge. I though my tip was over-the-top. A nice square tip with rounded edges would look hot. I also agree about there not being much room to hide the muffler. Does anyone make a nice Euro looking skirt extension? SOmething like the stock GTIs have? That would be nice.
ChinoCharlesOH · May 9, 2007#29
Not to diss on the product, but I expect more from a company like Blitz than to ship a product any less than perfect. That is extremely disappointing. They should be buying you a new rear bumper.
GalavoxxSan Francisco · May 9, 2007#30
Agreed.
Ran KizamaThread starterCanton, GA · May 9, 2007#31
Originally Posted by ChinoCharles ↑
Not to diss on the product, but I expect more from a company like Blitz than to ship a product any less than perfect. That is extremely disappointing. They should be buying you a new rear bumper.
Again, not sure if it was damaged or just a production error. Either way, it's half my fault. Realizing the potential hazard, I should have put the stock one back on until I got the proper hangers. I was just too pressed for time at the moment.

Like I said before, I'd be a lot more upset if I wasn't going to do the INGS+ kit in the near future. A rear skirt should cover the burn well enough and if I don't put on a rear skirt, I'll cover it with an aluminum heat shield. 🙂
Doc ZaiusOttawa, ON, Canada · May 9, 2007#32
Guys guys.... its because it was built for the Japanese RS bumper, which has an indentation cut out for the muffler. Exact same reason you need longer hangers for the JDM TRD muffler. Not a product defect.

Just all the more reason to go import the rear RS bumper! 😁
ChinoCharlesOH · May 9, 2007#33
No, see, it isn't your fault. You paid good money for a quality product only for it to arrive defective. You said there was no obvious visible damage to the box, but if outside forces were to bend the hanger you'd know by looking at the box. That takes a lot of force. So, Blitz fucked up and you're left with a scorched bumper. If you don't e-mail them I'm doing it for you. 🙂

I think this is symptomatic of an issue I see with a lot of companies making parts for this car. These well-established companies think they're so talented anymore that they don't need to test fit products before shipping. If Blitz put that exhaust on the car before they started shipping them, why in the hell did you get one that scorched the bumper? My bet? A hiccup in their research department and a lack of testing led to your little problem. This isn't the only time I've seen this... how many parts have we seen now that have minor (or major) fitment issues? I know the car is hard to get a hold of for testing, but Jesus...

EDIT: Doc, you're probably right... but the seller and/or the company producing the product didn't care to mention this to US buyers? I expect better service and support from companies charging big bucks for their products. This exhaust isn't cheap! 😠
Ran KizamaThread starterCanton, GA · May 9, 2007#34
Thanks Charles, I appreciate the enthusiasm. (^_^) Still, the scorch isn't visible at all from the rear and since I plan on covering it, I'm not that all mad. A little, yes, but I think I'll live. If Blitz tells you that they'll fix/replace my bumper, let me know. 😁
Doc ZaiusOttawa, ON, Canada · May 9, 2007#35
Originally Posted by ChinoCharles ↑
... but the seller and/or the company producing the product didn't care to mention this to US buyers? I expect better service and support from companies charging big bucks for their products. This exhaust isn't cheap! 😠
TRDSparks doesn't mention it, and lots of members bought the TRD muffler from them. I dunno... as a consumer, I would definitely appreciate being told that the muffler is meant for a particular bumper, and if used on a different one (i.e. USDM) and it's touching, you should not drive with it or expain how to fix it, etc.

My $0.02.
Chris07LBNew Jersey · May 9, 2007#36
Ran that exhaust looks like shit.. you should pack it all up at once, and send it to New Jersey to be taken care of. 😉

No, really.. you should!
501oregon · May 10, 2007#37
Originally Posted by Doc Zaius ↑
TRDSparks doesn't mention it, and lots of members bought the TRD muffler from them. I dunno... as a consumer, I would definitely appreciate being told that the muffler is meant for a particular bumper, and if used on a different one (i.e. USDM) and it's touching, you should not drive with it or expain how to fix it, etc.

My $0.02.

the trd muffler was put on a stop sale from toyota. you have to convince the parts guy to go ahead and order that part. trdsparks had ordered alot of them beforehand and i believe two months ago he only had 4 left.i havent checked latley. toyota is/was going to release a usdm version due to the fact of possible fitment issues. any imported muffler will be only designed for the jdm body versions unless otherwise noted.

as a consumer we must remeber to ask about fitment issues. if that company tells you that fitment will not be an issue then they should be liable.most of us are aware of the body differences
Ran KizamaThread starterCanton, GA · May 10, 2007#38
So I e-mailed Blitz-Performance.com and notified them about the issue with their current NuR Spec Exhaust. Here is there reply.
___________________________________________

Dear Nathaniel,

We're sincerely sorry about your situation. We were not aware of the
fitment issue on the Yaris exhaust due to the rear bumper, we are greatly
appreciated that you shared this info with us. We will take proper
action to modify this exhaust for the US market. We are not able to offer you
reimbursement for the cost of repair of your bumper, but we can offer
you a heavy discount on any part that we offer for the Yaris like the R-Viti-Color, intake, etc.

Thank you for your interest in our products.


Staff
Blitz Performance Sales, Inc.
___________________________________________

I replied and thanked them for noting the situation and offering me a discount on another performance part. I humbly requested a deal on the R-FIT (Fuel Intensity Controller) for my Yaris. I'm now waiting for their reply. So far, the customer service at Blitz has been good. 👍
Chris07LBNew Jersey · May 10, 2007#39
Tell them you need a second exhaust for more testing.. asap. 😆
Ran KizamaThread starterCanton, GA · May 10, 2007#40
Originally Posted by Chris07LB ↑
Tell them you need a second exhaust for more testing.. asap. 😆
😆 😆 😆
ChinoCharlesOH · May 10, 2007#41
Cool Ran! Glad to see you got something out of the ordeal.
AstromanWenatchee, WA · May 10, 2007#42
I already melted my bumper with the TRD exhaust. At least you can't tell unless your underneath the car. Still not super excited that it happened though. I am glad nothing caught fire at least, and now that the tip melted part of the bumper off, no more issues! 😳
Ran KizamaThread starterCanton, GA · May 10, 2007#43
UPDATE!
_____________________________________

Dear Nathan,

For the R-Fit controller, we will be able to offer it to you for $250 shipped. List price on that product is $398.

Thank you for your interest in our products.


Staff
Blitz Performance Sales, Inc.
_____________________________________

Looks like I gotta schedule a dynotune. 😁 Blitz customer service FTW!!!
Chris07LBNew Jersey · May 10, 2007#44
😳

Tell them to become a vendor here!!
AlphaFoxSpringfield, Mass · May 11, 2007#45
Not to be a wise guy, but if the muffler is touching the bumper isnt it kind of obvious that it will melt?
nqdBoston, MA · May 11, 2007#46
yea makes sense but probably too excited to hear it
Chris07LBNew Jersey · May 11, 2007#47
Originally Posted by AlphaFox ↑
Not to be a wise guy, but if the muffler is touching the bumper isnt it kind of obvious that it will melt?
As mentioned already...........

Originally Posted by Ran Kizama ↑
Again, not sure if it was damaged or just a production error. Either way, it's half my fault. Realizing the potential hazard, I should have put the stock one back on until I got the proper hangers. I was just too pressed for time at the moment.
AlphaFoxSpringfield, Mass · May 11, 2007#48
Thanks Chris............................................. .................................................. .................................................. .................................................. .................................................. .....
YarisGuyUSA · May 15, 2007#49
Originally Posted by Ran Kizama ↑
UPDATE!
_____________________________________

Dear Nathan,

For the R-Fit controller, we will be able to offer it to you for $250 shipped. List price on that product is $398.

Thank you for your interest in our products.


Staff
Blitz Performance Sales, Inc.
_____________________________________

Looks like I gotta schedule a dynotune. 😁 Blitz customer service FTW!!!

That is some serious customer service! 🙌


.