Yarisworld Archive

final installation of nology hotwires

29 posts · 15,277 views

turboyarisOriginal postSouthern New Jersey · Apr 17, 2007#1
alright guys well I got around to remounting the nology hotwires yesterday. I have also included some pics of the engine i recently purchased after taking a few things off. first off though i will start again with the picture of the engine bay the way nology says to install them.
Picture not included in this copy
now i will walk you through the steps of installing them the way I did in case you like the looks of my engine bay, I apologize chino its still not clean haha 😁
First I started by removing the wiper cowl, which consists of popping off the wiper arm covers and removing the 14mm nut underneath, pull off the wipers and remove two plastic screw pieces on the far ends of the cowl, then just pull up and remove, remove the wiper fluid line and you can pull the cowl off and set it aside. From there I drilled two holes in the bracket supplied from nology for the ignition coils and I drilled two holes in the wiper cowl. Take care in measuring the distances to make sure the holes will line up the first time. I then just took two scrap pieces of a 90 degree angle about an inch in thickness and drilled two holes in that. After bolting each ignition coil to the bracket continue to then bolt the bracket to the 90 degree elbows and then to the wiper cowl. Here is a close up to give an idea at least.
Picture not included in this copy
Now on to the tricky part, luckily the engine I bought had extra igntion coils harnesses. This made it easy to run the wires before having to cut into the existing ignition harness run 4 wires for each it is easiest to get 16 different colors, but it is doable with 4. The white wire in each is actually a ground so what I did was splice into each of these wires and did a nearby ground wire connecting to the bolt securing the bracket to the wiper cowl.
Picture not included in this copy
It is easiest to wire everything up first as far as connecting all the wires before you try and hide the wires and everything, I added about 2 - 2 1/2 ft of wire I kept them together and straight out to make the wiring job easier.
Picture not included in this copy
After this I just soldered the wires together and wrapped them all in electrical tape making sure to cover the connections with shrink wrap as well. After that I just tucked the wires underneath the main harness and used black electrical tape to hold them in place. This is the final result before installing the engine cover.
Picture not included in this copy
once that was completed and the wires were connected to the ignition coils you can reinstall the wiper cowl. Oh I forgot to mention but before you tape everything up its a good idea to start the car and make sure all your wiring is done correctly. You do need slight modification to the stock engine cover. You are required to take a small portion off of the back drivers side of the engine cover it is easily done with a hacksaw or air body saw if you have, the plastic is very easy to cut, here is just a shot of the quick cut, it doesnt have to be cut pretty because it isn't possible to see this part of the cover.
Picture not included in this copy
and here is the final result
Picture not included in this copy
I wrote this over a decent amount of time and lost track of my thoughts a few times, if there is a step you feel i have missed or need more explaining just feel free to let me know. Also here are two pics I took while taking the extra engine apart last night
Picture not included in this copy
Picture not included in this copy

Replies 28

turboyarisThread starterSouthern New Jersey · Apr 17, 2007#2
p.s. i installed the TWM short shifter yesterday as well... Very nice I love the feel a lot better, kinda reminds me of my 240 with a B&M shifter. I got the bushings as well and it definately removes a lot of the squishiness in the shifter. Definately a good mod, only thing that gets me is I set real far back from the steering wheel and its a little more of a stretch then stock, but when I get some different seats in the car it will be lower and the reach will be just right.
yrsdrgnSF,CA · Apr 17, 2007#3
sorry to ask such a newbie question but what exactly do these do?
NutzoidsPhiladelphia · Apr 17, 2007#4
Originally Posted by yrsdrgn ↑
sorry to ask such a newbie question but what exactly do these do?
Provide more spark to the Engine!

😈


Tell us more about these Wires...

How much did they cost?
How long did the Installation take?
Has there been a noticable difference in How the Yaris responds?

Please more info!

😈
BlenjarCT · Apr 17, 2007#5
damn..thats alot of messing with engine...

-- Blen
turboyarisThread starterSouthern New Jersey · Apr 17, 2007#6
original post
here is the original post it should answer more of your guys questions sorry I forgot to include it.
yrsdrgnSF,CA · Apr 17, 2007#7
questions answered. Thanks and keep up the good work 👍
joey1320Lakewood, Ohio · Apr 18, 2007#8
turboyaris, what model year engine did you get for the spare? i went to pick up the echo engine from the junkyard but i didn't trust the guys there when they said they had done a compression/leakdown test.

so i asked them if i could get my leakdown tester and do one before taking the engine and they got all mad about me wasting their time. so i walked out.

anyways does it look exactly like the yaris'? or at least be able to swap it out once is build?
Black YarisToledo, OH · Apr 18, 2007#9
Originally Posted by turboyaris ↑
Picture not included in this copy
Holy Chain guide and tensioner, Batman!😲 Those are frickin long.... maybe I am just a noob to imports, never see em that long on domestics
07typeSSouthern California · Apr 18, 2007#10
That is a long ass chain......something you'd see wrapped around snoops neck....
turboyarisThread starterSouthern New Jersey · Apr 18, 2007#11
haha my 240sx had chain guides and a chain of about the same length so I don't think its anything too crazy, it's just a lot of people arent used to seeing the chain anymore everyone has a belt. As for the engine its out of a 2005 scion xb yes the engine looks exactly the same, it is the 1nz-fe only thing i would guess is different is maybe the cams. Esp. since the engine is out of an auto and my yaris is manual. After it is built though it will make no difference castings are probably exactly the same.
turboyarisThread starterSouthern New Jersey · Apr 18, 2007#12
i also didn't really care about doing a leakdown test or compression test, however the place I got my engine from was a very upscale junkyard (if you can believe) they had everything for almost every car, front clips for porsches stuff like that. They actually had a startup warranty on it, not too sure about the details cause once again I didn't really care because it was all being dismantled and taken apart. There are a few very upscale looking junkyards in the pittsburg area I don't really know where in OH you are but I would just go to www.car-part.com and see if the junkyard has a website, just to get an idea of what level of junkyard they are.
joey1320Lakewood, Ohio · Apr 19, 2007#14
thanks man. i checked that link and it says they have 3 in stock for $250. great deal.
Vic-2NZFEPanama · Apr 19, 2007#15
Have you taken your car to the dyno once again to see actual numbers?
nice DIY but kinda a lot of work messing with cables an others.
Yaris RevengeMy own little world. · Apr 19, 2007#16
I'm not very clear on how "more spark" is supposed to help combustion any? If you have a bucket of gasoline, it's gonna blow up the same... doesn't matter if you use a torch or a match to set it off. Can someone explain?

~YR
NimbleChicago, IL · Apr 19, 2007#17
Cool project! And if you got that new of a motor for only $250, I think you did good. So what are the plans for the new motor?
GalavoxxSan Francisco · Apr 19, 2007#18
The re-route looks great. And you making me more and more jealous with your setup. Stop upgrading already!!! Seriously though, nice work. 👍
turboyarisThread starterSouthern New Jersey · Apr 19, 2007#19
I'm not very clear on how "more spark" is supposed to help combustion any? If you have a bucket of gasoline, it's gonna blow up the same... doesn't matter if you use a torch or a match to set it off. Can someone explain?
your best bet is too look on nology's website they have a pretty informative Q&A section basically though your right you can light a pool of gas with a match but have you tried, it actually take a little bit of time for the pool to light, it takes less time with a torch. The same general rule applies.
So what are the plans for the new motor?
well basically no one makes any internals for our engine. Some companies have made custom parts for it, basically though I am going with a fully built engine so it can take some high levels of boost. I'm going for fastest street Yaris in the country. I like being on the forefront and developing new parts. Expect a lot of updates on the engine build as I get more and more of the info about our engines. Custom internals take a lot of work esp piston design and cam design.
The re-route looks great. And you making me more and more jealous with your setup. Stop upgrading already!!! Seriously though, nice work.
sorry i'm a car guy I can never stop tinkering or upgrading. I have two projects in the works already that will hopefully be done or nearing completion soon. The one is the intake/manifold, soon I will post side by side pics of the throttle bodies its quite amusing how small our TB's are. The other is some aero work, with an aluminum underpanel, and maybe some underbracing. I will keep you posted.


And yes it is a lot of work, but personally I feel it is worth it because If i have to show off my engine bay I want it to look nice and clean, plus I am still trying to go for that sleeper look so I wanted it to look semi stock. I haven't been able to dyno the difference, I will get on the dyno soon but it wont be able to give you good before and after dyno results becuase the numbers will be from different conditions.

The only thing to inform you guys about, I'm told that the nology wires will work fine on a stock setup, but just so you guys know, I was able to finally get on it (since I live in the city I havent been able to) I have a miss at the top of 2nd and 3rd gear. I know this is because with the stock ignition system my tune required the timing to be adjusted and now it only needs adjusting again because the way the wires perform. I don't believe you guys should have to adjust your timing at all because the ecu will probably compensate for it, however since my ignition is set, it needs some further adjustment. Just so you guys are aware of the situation.
GalavoxxSan Francisco · Apr 19, 2007#20
Can't wait to hear more. 🤤
joey1320Lakewood, Ohio · Apr 19, 2007#21
Originally Posted by turboyaris ↑
your best bet is too look on nology's website they have a pretty informative Q&A section basically though your right you can light a pool of gas with a match but have you tried, it actually take a little bit of time for the pool to light, it takes less time with a torch. The same general rule applies.

well basically no one makes any internals for our engine. Some companies have made custom parts for it, basically though I am going with a fully built engine so it can take some high levels of boost. I'm going for fastest street Yaris in the country. I like being on the forefront and developing new parts. Expect a lot of updates on the engine build as I get more and more of the info about our engines. Custom internals take a lot of work esp piston design and cam design.

sorry i'm a car guy I can never stop tinkering or upgrading. I have two projects in the works already that will hopefully be done or nearing completion soon. The one is the intake/manifold, soon I will post side by side pics of the throttle bodies its quite amusing how small our TB's are. The other is some aero work, with an aluminum underpanel, and maybe some underbracing. I will keep you posted.


And yes it is a lot of work, but personally I feel it is worth it because If i have to show off my engine bay I want it to look nice and clean, plus I am still trying to go for that sleeper look so I wanted it to look semi stock. I haven't been able to dyno the difference, I will get on the dyno soon but it wont be able to give you good before and after dyno results becuase the numbers will be from different conditions.

The only thing to inform you guys about, I'm told that the nology wires will work fine on a stock setup, but just so you guys know, I was able to finally get on it (since I live in the city I havent been able to) I have a miss at the top of 2nd and 3rd gear. I know this is because with the stock ignition system my tune required the timing to be adjusted and now it only needs adjusting again because the way the wires perform. I don't believe you guys should have to adjust your timing at all because the ecu will probably compensate for it, however since my ignition is set, it needs some further adjustment. Just so you guys are aware of the situation.

well there are aftermarket performance rods/pistons. you can get them here:

http://www.raceeng.com/searchadv.asp...=21&submit.y=9

i have bougth from race eng. and they are great.
awesome customer service and attention to details. good luck.
i can't wait to pick up an extra engine.🙂

http://www.raceeng.com/searchadv.asp...=21&submit.y=9
turboyarisThread starterSouthern New Jersey · Apr 19, 2007#22
thanks for the link the crower rods I was probably going to go with, I might change up some of the specs though haven't fully decided as for the pistons, I am having the block sleeved so I want more then just .5 mm overbore you know. but thats definatly helpful for the people that just want to purchase off the shelf and don't want the hassle of custom work. ZPI also has rods and pistons on their site. Just for fyi for you guys.
joey1320Lakewood, Ohio · Apr 19, 2007#23
Originally Posted by turboyaris ↑
thanks for the link the crower rods I was probably going to go with, I might change up some of the specs though haven't fully decided as for the pistons, I am having the block sleeved so I want more then just .5 mm overbore you know. but thats definatly helpful for the people that just want to purchase off the shelf and don't want the hassle of custom work. ZPI also has rods and pistons on their site. Just for fyi for you guys.


cool man. definitely keep us updated on the build. i will go with stock bore or maybe .5mm over. i never like to take metal away from the cyl. walls if i don't have to, so just a honing' job will be used.

plus the fact that you put down over 180whp with a stock engine, i know with these parts i could easily get over 220whp which is what i'm shooting for.
turboyarisThread starterSouthern New Jersey · Apr 19, 2007#24
on their scion xb zpi actually upped the boost to 12 psi and had about 230 to the wheels but with slicks, the snapped the axles. They said the engine held fine, now for how long is another story. I am shooting for a decent amount higher then 220 to the wheels. but yea a stock bore with beefier components would definately allow for 220 to the wheels. just be careful with our tiny axles. and taking metal away isnt too bad if like i am doing you sleeve it. it allows for a bigger bore, i'm hoping to be able to get a couple mm over bore, maybe have a 1.6 liter engine haha.
joey1320Lakewood, Ohio · Apr 20, 2007#26
Originally Posted by turboyaris ↑
on their scion xb zpi actually upped the boost to 12 psi and had about 230 to the wheels but with slicks, the snapped the axles. They said the engine held fine, now for how long is another story. I am shooting for a decent amount higher then 220 to the wheels. but yea a stock bore with beefier components would definately allow for 220 to the wheels. just be careful with our tiny axles. and taking metal away isnt too bad if like i am doing you sleeve it. it allows for a bigger bore, i'm hoping to be able to get a couple mm over bore, maybe have a 1.6 liter engine haha.
nice to know that zpi got those numbers. and if you are gonna sleeve the block then you should be more than ok to bore it. i just wanna keep the stock sleeves and replace the rods/pistons, headgasket and head bolts.

i'm not sure if i wanna do anything with the head, if any i'll just replace the valvetrain with stock size/angle units and go from there. i don't like messing with the original equipment. i just like to make it stronger.

good luck!
turboyarisThread starterSouthern New Jersey · Apr 22, 2007#27
alright guys just to clear it up, I regapped my spark plugs down to .035 instead of the stock .044 as I was advised to do by nology and now... no more misfires at high rpms. Just to clear that up, I was pretty sure that was the problem.
jiovannyvenezuela · May 14, 2015#28
good afternoon people, great forum, I write from venezuela, I wanted to know more information about the post: cables are? What are the coils? in that I help? If you improve performance?

Thank you very much in advance:burnrubber:
jiovannyvenezuela · May 14, 2015#29
good afternoon people, great forum, I write from venezuela, I wanted to know more information about the post: cables are? What are the coils? in that I help? If you improve performance?

Thank you very much in advance