abstractmethodOriginal postAustralia · Feb 21, 2014#1Hi guys,
just wanted to post some progress shots of my stage 1 turbo build, more so i can keep track and not loose photos in the process.
Purchased my self a 1NZ-FE motor to work on so my car wouldnt be off the road, just landed a job with Samsung and a 2 minute walk from home so wouldnt have mattered any way.
So far we've got the following parts:
* 2ZZ injectors
* Zage manifold (custom one to be built by Brae manifolds down the track, check him out at
https://www.facebook.com/pages/Brae-...7816811564704_ *T28 turbo running customer oil and water lines (yes im using both)
* Turbosmart black FPR800 fuel pressure reg
* Turbosmart Kompact plumb back BOV
* Golden eagle black fuel rail
* Microtech LTX-8
* Custom black piping
* Bosch 040 fuel pump - in tank mod needed
Ill keep up to date with some photos as the build progresses.
Picture not included in this copy Picture not included in this copy Picture not included in this copyReplies 21
abstractmethodThread starterAustralia · Feb 22, 2014#2All the water lines and oil lines were ordered today, used a mob in Japan who stock Kinugawa turbo's, their stuff has always been really good quality. Will post pics once they arrive and they have been installed.
bebeeloStockton, CA · Feb 22, 2014#3just curious...how much is this build going to cost?
abstractmethodThread starterAustralia · Feb 22, 2014#4There is no budget. Stage 1 will be manifold, turbo, microtech and injectors. Stage 2 will built on a separate motor were I can take time to fit rods, pistons, valves and cam so the car is not taken off the road.
cali yarisCanoga Park, CA · Feb 22, 2014#5THUMBS UP! [subscribed]
abstractmethodThread starterAustralia · Feb 26, 2014#6So after a lot of thought, research and thinking of building the motor, then installing it, running it in, driving it around, removing it for stage 2, i just decided to bite the bullet and skip straight to stage 2...
Today's progress consisted of removing the intake manifold, water pump, spark plugs, engine mount, timing cover, cams and turbo.
Unfortunately for me i stripped three of the head bolts, will rectify this next monday and finally get the head off, get it sussed out and order rods, pistons, bearings, block guard etc...
I also decided not to go the microtech route, I will be ordering a Haltec P1000 ECU or Link G4.
Here are a few photos from today.
Picture not included in this copy
Picture not included in this copy
Picture not included in this copy
Picture not included in this copy
Picture not included in this copy
Picture not included in this copy
Picture not included in this copy
cali yarisCanoga Park, CA · Feb 26, 2014#7I believe ARP has a head stud kit now. Let us know if you need any parts for your build, we are very competitive.
abstractmethodThread starterAustralia · Feb 26, 2014#8 Originally Posted by
cali yaris ↑ I believe ARP has a head stud kit now. Let us know if you need any parts for your build, we are very competitive.
Hi there and thanks for the reply. Already sent you a Msg just waiting on reply
GolddeenohColumbia, SC · Feb 26, 2014#9Just be like me and have MI set to speed dial.👍 why do I ,because
abstractmethodThread starterAustralia · Feb 27, 2014#10Haha I'm from Aus so I'd be paying a hefty bill in international call charges.
Doing some research on rods and pistons. Seems Cp-corello are about the only guys doing forged pistons off the shelf... Do MI normally reply quickly?
fnkngrvIn The Hotbox · Feb 27, 2014#11CP is a great choice for pistons. There are several options for rods; pauter, carillo, cunningham, etc.
Bluevitz-rsOshawa, Ontario, Canada · Feb 27, 2014#12Garm do you know what rods require the block to be notched?
abstractmethodThread starterAustralia · Feb 27, 2014#13What's the deal with notching the block? I haven't heard of this needing to be done before?
Bluevitz-rsOshawa, Ontario, Canada · Feb 27, 2014#14Well the 1NZ block has the crankshaft 3° offset to the bore to improve power stroke pushing angle. It reduces loads in the power stroke but increases stress on the rod on compression. The aftermarket rods being beefier hit the side of the block. Well some do and some don't. Actually I think it's more the side of the bore than the block.
abstractmethodThread starterAustralia · Feb 28, 2014#15I'm still waiting in MI to get back to me regarding rods and piston advice.. I guess most engine workshops will have the ability to notch the block if needed.
Today I ordered my haltech p1000 ecu, wide and sensor and march boost controller which integrates with the p1000.
cali yarisCanoga Park, CA · Feb 28, 2014#16^ I got back to you. You PM'ed me four hours ago. 🙂
Garm do you know what rods require the block to be notched?
All of them. They are all thicker than stock (that's kind of the point), and so require the mod.
abstractmethodThread starterAustralia · Feb 28, 2014#17Thanks mate. I had issues sending you a message for days hahaha. Every time I sent one it wouldn't give me confirmation so I was like "uhhhhhh has it sent".. downside to using this forum from a phone lol
abstractmethodThread starterAustralia · Mar 3, 2014#18So as you know I stripped the head bolts.. Mainly because I used the wrong tool.. finally found the right 12" spline after purchasing 2 supposedly correct splines that were listed in online 1nz-fe engine disassembly threads.. aus delivered engines must use different studs for some reason.. any ways I eventually got the right one $84 later :S ridiculous huh!
Picture not included in this copy
Paris vvt-iAthens · Mar 12, 2014#19If you want my opinion DO NOT use a block guard!
Bluevitz-rsOshawa, Ontario, Canada · Mar 12, 2014#20Why does it cause cooling issues?
abstractmethodThread starterAustralia · Mar 13, 2014#21Thanks mate. I've been told this a few times. Any reasoning behind it. I've been told it stops effective cooling to the block...
Paris vvt-iAthens · Mar 13, 2014#22two reason:
1) they can cause hot spots and overheating
2) there is no proof stock sleeves can hold more power and torque with a block guard than without it ==>> completely useless (this from the honda b16 world wich have weaker sleeve design). the block guard has a little space bettwen itself and the sleeve. it does not hold the sleeve.
what power/ torque level are you aiming for?