Yarisworld Archive

minimum Turbo'n

27 posts · 7,202 views

GolddeenohOriginal postColumbia, SC · Feb 8, 2014#1
What are the minimum requirements to have a simple turbo set up on the Yaris?

for instance

turbo
exhaust manifold
down pipe
piping
(maybe inter-cooler)
bov/waste gate (7psi)
boost controller
boost guage
oil feed to and from turbo back to engine
Coolant lines to and from turbo
Piggy back required at minimum(and some way to connect it)
Air/Fuel Ratio gauge

anti-foulers needed(depends on tune)
ungraded injectors 1ZZ (depends on tune)

Additional Information from one of the Yaris Turbo masters:
Ultimate Turbo Pre-Install Guide

Replies 26

cali yarisCanoga Park, CA · Feb 8, 2014#2
You can't boost the car on just the stock ECU.

psi depends on the wastegate spring. You can just run the spring and not use a controller to save money. (but I don't recommend it)

You left out oil and water lines.
ilikericesavannah, ga · Feb 9, 2014#3
drop the boost to about 2-3 and you can use the stock ECU... but they why have a turbo to begin with?
like Garm said
Engine management is a requirement to keep your motor safe or you will be buying a new motor not too long after that turbo is put on.
cali yarisCanoga Park, CA · Feb 9, 2014#4
drop the boost to about 2-3 and you can use the stock ECU...
Is there a thread where someone did this?
BEEFnorth carolina · Feb 9, 2014#5
I want to say malibuguy did this on his echo (the low boost thing)
GolddeenohThread starterColumbia, SC · Feb 9, 2014#6
there isn't much point to boosting unless there is at least 7 psi of boost, giver or take 1 psi, so the management is a must.

I updated the list to include the fluid line and managment

what about injectors and o2 sensor anti-foulers?
cali yarisCanoga Park, CA · Feb 9, 2014#7
There's only one anti-fouler, between the cats. if you are running a stock exhaust you may or may not need it.

Injectors, you have to see, as you are basically tuning the car with them. I would have 1ZZ injectors on hand to swap in.

You left off an air/fuel gauge, CRITICAL so you can monitor how your motor is running.
malibuguyWestminster, MD · Feb 10, 2014#8
Originally Posted by BEEF ↑
I want to say malibuguy did this on his echo (the low boost thing)
i ran 3.5 on my tercel completely stock EFI. The car was awesome. After I was sure of my set up, bigger injectors went in & so did the AEM...& now i'm running 16lbs...😲
BEEFnorth carolina · Feb 10, 2014#9
Originally Posted by malibuguy ↑
i ran 3.5 on my tercel completely stock EFI. The car was awesome. After I was sure of my set up, bigger injectors went in & so did the AEM...& now i'm running 16lbs...😲
16# on stock internals?
fnkngrvIn The Hotbox · Feb 10, 2014#10
The Zage kit isn't a complex setup. Why not one of those or use as a model? Also need conical air filter right? Also I at a loss how an IC would be optional?
fnkngrvIn The Hotbox · Feb 10, 2014#11
Oh yeah...I never paid attention. How well does the stock exhaust piping handle 6-8psi?
cali yarisCanoga Park, CA · Feb 11, 2014#12
You can run a low-boost turbo without an intercooler. The air gets hotter (obviously) so it doesn't make as much power.

I don't recommend it, mostly because it's not THAT much more work to run an intercooler set up -- but it CAN be done.
GolddeenohThread starterColumbia, SC · Feb 11, 2014#13
The point of the thread is to obtain a turbo set up for as cheaply as possible while still being able to drive the car every day. ideally a cheaper set up that can be expanded upon.

Zage is nice but if one would start with a basic set up t3/t4 turbo, then the expansion possibilities would be better once further funds became available.

I am under the impression that anything above 8psi will lead to a bent connecting rod. correct?

personally, I would inter-cooler, but if push comes to shove, it can be bypassed to save a few buck but lose some HP.

At some point MI will finally get a mid pipe in and stock exhaust will no longer be a problem.
cali yarisCanoga Park, CA · Feb 12, 2014#14
I think the point of the thread is being served quite well... for once. 😆
GolddeenohThread starterColumbia, SC · Feb 12, 2014#15
Originally Posted by cali yaris ↑
I think the point of the thread is being served quite well... for once. 😆
yea, now about that mid-pipe? 😕😆
fnkngrvIn The Hotbox · Feb 13, 2014#16
For the most part you aren't going to start risking rods until over 10psi, but if you have a shit tune I would think it is possible to ruin a rod. Regardless of that if you run lean all the time you could damage even at 8. It also depends on how you drive it.
Blown_xaVirginia · Feb 13, 2014#17
Hey guys remember, boost doesn't bend rods. Power and detonation does. I built my roomies xB and with a 3.5psi wastegate spring it is making more power than the stock motor should handle because it has a t3 60 trim coupled with an efficient setup. When I had my Greddy kit I needed to run 15 psi to make the same power.
GolddeenohThread starterColumbia, SC · Feb 14, 2014#18
Originally Posted by fnkngrv ↑
For the most part you aren't going to start risking rods until over 10psi, but if you have a shit tune I would think it is possible to ruin a rod. Regardless of that if you run lean all the time you could damage even at 8. It also depends on how you drive it.
Originally Posted by Blown_xa ↑
Hey guys remember, boost doesn't bend rods. Power and detonation does. I built my roomies xB and with a 3.5psi wastegate spring it is making more power than the stock motor should handle because it has a t3 60 trim coupled with an efficient setup. When I had my Greddy kit I needed to run 15 psi to make the same power.
hoping to use a t3/t4 Hybrid set up, probably going to have to cut on one of Garm's t25 headers to make it work for a t3 flange. so it is up to the tune and set up, not simply the psi being used.
vaironl-- · Feb 14, 2014#19
I don't know poop about turbos, as I'm just starting to learn about it.
But, isn't this a well documented thread? Link: Ultimate Turbo Pre-Install Guide
cali yarisCanoga Park, CA · Feb 15, 2014#20
^ GREAT link. 👏
GolddeenohThread starterColumbia, SC · Feb 16, 2014#21
Thanks for the link i have added it to the information.
GolddeenohThread starterColumbia, SC · Mar 3, 2014#22
after talking to the wife and figuring up the numbers, i'm just going to keep it going and reliable and possibly sale it to go buy me a Hemi (Challenger SRT8).
cali yarisCanoga Park, CA · Mar 3, 2014#23
^ I knew that was coming. 😆
sqcompBack at home · Mar 28, 2014#24
Detonation...reduce it by using higher octane gas (premium at least)/e85...

With e85 you're talking about redoing the fuel pump to keep up with demand. IIRC you can use C16 with a stock fuel pump because of the weight (?) of the fluid versus e85*.

Garm, your former Yaris's engine was fully built wasn't it? What did you have for compression?

*=I'm not sure on the Yaris's fuel system. On my other car, that's a yes.

Being as cheap as possible usually doesn't lend itself well. If you're going to play around with this stuff, don't get yourself stuck on the side of the road, especially if the car is your DD.
malibuguyWestminster, MD · Mar 28, 2014#25
Originally Posted by BEEF ↑
16# on stock internals?
Yep with 290k on em
fnkngrvIn The Hotbox · Mar 28, 2014#26
Unless I am totally mistaken the biggest and ppossibly only issue with going with racing fuel over the VP100 level would be possible plugging of your cat would it not?
BEEFnorth carolina · Mar 28, 2014#27
Originally Posted by malibuguy ↑
Yep with 290k on em
Sir, your ballsack must be the size of texas....

I would love to see the dyno sheet of that one. I am sure I have read (a few times over) that the absolute limit was somewhere around 10# at around 200hp at the tires. Are you sure your connecting rods aren't shaped like squiggly lines by this point 🙂