bronsinOriginal postnj · Aug 27, 2013#1I want to remove my passanger seat.
Is there already a DIY?
Thanks!
Replies 19
CTScottUSA, CT · Aug 27, 2013#2You need an E10 socket for the bolts (an inverse torx). Slide the seat back, and remove the two front bolts, slide it forward and remove the two rear bolts, disconnect the connector to the passenger occupancy ECU (which is mounted to the bottom of the seat) and lift it out.
If you turn the ignition on while the seat is removed you will log some DTCs for the SRS ECU, and the airbag light will stay illuminated on the dash. Once you put in back in you can clear them using this procedure:
Airbag light panel is ON bronsinThread starternj · Aug 28, 2013#3CAn you drive the car with the seat out? I want to go 500 miles. Whats a dct?
CTScottUSA, CT · Aug 28, 2013#4 Originally Posted by
bronsin ↑ CAn you drive the car with the seat out? I want to go 500 miles. Whats a dct?
You can, but will log DTCs (diagnostic trouble codes) on the SRS ECU and will have to reset them after.
bronsinThread starternj · Aug 28, 2013#5Wow that sounds complicated. And my NJ inspection is coming up next April. All they do for that is check the computer for codes. It would suck if I couldnt clear them.
I have a scan tool will that reset it?
How about having Toyota do it...for free?
CAn you plug a pretend seat into the connector?
CTScottUSA, CT · Aug 28, 2013#6 Originally Posted by
bronsin ↑ Wow that sounds complicated. And my NJ inspection is coming up next April. All they do for that is check the computer for codes. It would suck if I couldnt clear them.
I have a scan tool will that reset it?
How about having Toyota do it...for free?
CAn you plug a pretend seat into the connector?
No
No
Yes - My Occupant Classification Bypass Module (which Micro Image sells) will do the trick perfectly:
http://shop.microimageonline.com/Air...dule-OCSBM.htm bronsinThread starternj · Aug 28, 2013#7That jumper proceedure...
If you made a wire with a pair of connectors on the end and a switch in the middle Im thinking that would make the job easier....
CTScottUSA, CT · Aug 28, 2013#8 Originally Posted by
bronsin ↑ That jumper proceedure...
If you made a wire with a pair of connectors on the end and a switch in the middle Im thinking that would make the job easier....
Indeed it would.
bronsinThread starternj · Aug 28, 2013#9SO it looks like you attach the jumper with a switch, ignition off switch on.
Switch on ignition.
Cycle the switch for times cued by the SRS light going on or off.
If the error codes dont flash you did it!
bronsinThread starternj · Aug 28, 2013#10OH you can also READ THE CODES with this setup!
(slowly the lights go on in my brain)
As well as banish them for inspection!
A poors mans scan tool!
WOW!
That switch with the connectors is a MUST HAVE!
WHats a good connector to use?
CTScottUSA, CT · Aug 28, 2013#11 Originally Posted by
bronsin ↑ OH you can also READ THE CODES with this setup!
(slowly the lights go on in my brain)
As well as banish them for inspection!
WOW!
That switch with the connectors is a MUST HAVE!
WHats a good connector to use?
Something like this:
http://www.ebay.com/itm/NEW-OBD2-16-...3ad989&vxp=mtr nookandcrannycarS.MontgomeryCnty,TX(HoustonMSA) '07=BayouBlue=300,125miles=OrigOwnr '14=ClassicSilvr=29,059miles · Aug 28, 2013#12 Originally Posted by
CTScott ↑ Yes - My Occupant Classification Bypass Module (which Micro Image sells) will do the trick perfectly:
👏👏👏👏👏 Amazing. In addition to the Yaris, would this device also work on a RAV4 and/or a standard Prius?
CTScottUSA, CT · Aug 28, 2013#13 Originally Posted by
nookandcrannycar ↑ 👏👏👏👏👏 Amazing. In addition to the Yaris, would this device also work on a RAV4 and/or a standard Prius?
It will work an all Toyota vehicles that use the 89952-035011 Passenger Occupancy ECU. Which is >90% of Toyotas from 2005-2011. My largest market has actually been for FJ Cruisers.
mario98cPuerto Rico · Aug 28, 2013#148mm socket works too.
bronsinThread starternj · Aug 29, 2013#15 Originally Posted by
mario98c ↑ 8mm socket works too.
Cool I have one of those. 🤘
Wont an 8mm wrench work too? 🤷
mario98cPuerto Rico · Aug 29, 2013#16It's very difficult to use a wrench there. I will use the socket. 😁
CTScottUSA, CT · Aug 29, 2013#17 Originally Posted by
bronsin ↑ Cool I have one of those. 🤘
Wont an 8mm wrench work too? 🤷
Be careful if you use an 8mm socket instead of an E10. The bolts go through the floor, so if there is any corrosion on the bottom end you will risk rounding them off with the 8mm.
mario98cPuerto Rico · Aug 29, 2013#18That's true! Also the socket.that I use is the one that has 6 face. If the socket wiggle in the bolt, don' even try it.
nookandcrannycarS.MontgomeryCnty,TX(HoustonMSA) '07=BayouBlue=300,125miles=OrigOwnr '14=ClassicSilvr=29,059miles · Aug 29, 2013#19👍
Originally Posted by
CTScott ↑ My largest market has actually been for FJ Cruisers.
Very interesting. Of all the larger Toyotas I've ever seen being driven around (with light enough windows), the only one I've never seen fewer than two people in is an FJ Cruiser.
nookandcrannycarS.MontgomeryCnty,TX(HoustonMSA) '07=BayouBlue=300,125miles=OrigOwnr '14=ClassicSilvr=29,059miles · Sep 3, 2013#20 Originally Posted by
bronsin ↑ my NJ inspection is coming up next April. All they do for that is check the computer for codes. It would suck if I couldnt clear them.
When I first read this, I thought thank goodness we don't have that re the yearly inspection in Texas. Subsequent to reading this, I (on Saturday 8-31-13) had my yearly inspection done......😳........I read the whole report.....it appears that part of the inspection = same as in New Jersey.