caineroadOriginal postToronto · Jul 19, 2013#1Will there be any problem if I hook up LEDs to the dimmer switch?? Does the current light such as the center console knob gets dimmer because of the extra draw?
Judging from this from CTScott
----------
10 Pin connector D29
Pin 1 - N/C
Pin 2 - Light Green: Output to radio, AC lights, etc
Pin 3 - White/Black: Ground
Pin 4 - N/C
Pin 5 - Brown: Power in from PANEL1 fuse
Pin 6 - N/C
Pin 7 - N/C
Pin 8 - Yellow: Output to Cluster
Pin 9 - Orange: Output to Hazard warning signal switch and Door lock switch
Pin 10 - Sky Blue: Power in from GAUGE Fuse (Ignition switched)
---------
Should I tap the light green wire to power my LEDs?
Thanks
Replies 9
47_MasoN_47Northwest Alabama · Jul 19, 2013#2You'd have to hook up quite a bit of LEDs to cause anything to dim. I've got 8 LED strips running off the door-open circuit and nothing is any dimmer than it was before.
mazillaSan Jacinto California · Jul 19, 2013#3From what I recall seeing here and there tapping that dimmer is a no-go...seems to be responsible for problems most of the time. Don't quote me on that however.
caineroadThread starterToronto · Jul 19, 2013#4 Originally Posted by
47_MasoN_47 ↑ You'd have to hook up quite a bit of LEDs to cause anything to dim. I've got 8 LED strips running off the door-open circuit and nothing is any dimmer than it was before.
i see
caineroadThread starterToronto · Jul 19, 2013#5i am just thinking though if there is any wire I can connect to that is wire with the dimmer switch, i can tap that for easy access, cuz I plan to install the LEDs in the rear as foot well lightning.
jcboyAsia · Jul 23, 2013#6lucky for me i'm using the foglight switch illumination wire. our dimmer switches are located under the hazard button, and is only for the gauge.
i used that to wire up the door lock switch (center console, we don't have it here) so if it's any help, look for the wires that illuminate your switch (US/CA models usually have this switch) and wire from there.
johnbobgrayson, ga · Jul 24, 2013#7I used the wire off the radio (green radio illumination wire off back of radio) my problem is I shorted this wire and while I replaced fuse and got power back, I no longer have dash or speedo illumination once I turn on parking light switch. Lights on dash on when parking switch off / off when parking light switch on. Anyone aware of a relay for dim/bright function of dash lights that perhaps I knocked out?
caineroadThread starterToronto · Jul 24, 2013#8So you have replaced PANEL1 fuse, radio lights work when you turn headlights on but speedo and dash are dark? Does the speedo lit up when you turn off headlight?
If u have dimmer switch make sure its functioning properly
johnbobgrayson, ga · Jul 24, 2013#9Speedo does light up when headlight switch is in off position.
Fuse it blew was 7.5a for panel lights. Fuse replaced.....wait a minute
Damn dude your genius, must have rolled the dimmer down by mistake in process of replacing fuse. Not usually ham-handed doing repair and wiring work. Problem was kicking my butt because I was reading voltage at radio wire. Thank you for the suggestion/problem solve.
caineroadThread starterToronto · Aug 21, 2013#10Just wanna update if anyone is doing dimmer in the future,
I have found a way at least for me it works the best is to tap into the AT shift light both the positive and negative wire, I have since connected 4 Leds to it without problem. It's easy and convenient. dim-able with the dimmer switch