swiddOriginal postCentral Alabama, GOD BLESS AMERICA · May 2, 2013#1Replies 23
cali yarisCanoga Park, CA · May 2, 2013#2swiddThread starterCentral Alabama, GOD BLESS AMERICA · May 2, 2013#3Thanks, but ctscott beat you to it.
cali yarisCanoga Park, CA · May 3, 2013#4^ He sent you one of mine. Cool!
swiddThread starterCentral Alabama, GOD BLESS AMERICA · May 11, 2013#5cali yarisCanoga Park, CA · May 11, 2013#6SWEET! Can I post one of those on our Facebook page?
swiddThread starterCentral Alabama, GOD BLESS AMERICA · May 11, 2013#7Yeah, spread away.
swiddThread starterCentral Alabama, GOD BLESS AMERICA · May 14, 2013#8Oy, how exactly do I open the switch to snip the resistor?
CTScott, did you snip a resistor?
Right now I've installed the kit, but the fog lights do not turn on. However the switch lights up, even when the key is out of the ignition, ie hot bus.
Seeing as I broke the previous switch without even getting it open, there must be a trick to opening it that I don't understand.
CTScottUSA, CT · May 14, 2013#9 Originally Posted by
swidd ↑ Oy, how exactly do I open the switch to snip the resistor?
CTScott, did you snip a resistor?
Right now I've installed the kit, but the fog lights do not turn on. However the switch lights up, even when the key is out of the ignition, ie hot bus.
Seeing as I broke the previous switch without even getting it open, there must be a trick to opening it that I don't understand.
The one I shipped I pre-snipped, so you should just plug her in.
If the light is always on and the switch does not turn the fogs on, it sounds like you have a wiring issue. Post a pic of where the switch wires are connected to.
swiddThread starterCentral Alabama, GOD BLESS AMERICA · May 14, 2013#10CTScottUSA, CT · May 14, 2013#11swiddThread starterCentral Alabama, GOD BLESS AMERICA · May 14, 2013#12So for option 6 b, fog lights on with low, high and park:
I will be plugging both wires from the switch into 13 and 3? But 3 doesn't connect to anything...
Am I supposed to just remove the wires that are in there already, and leave them hanging unconnected?
cali yarisCanoga Park, CA · May 14, 2013#13We only have one set of instructions posted, for the aftermarket round switch. They would not be correct for the rectangular switch we used to include (a big reason was because of the modification needed on the switch)
CTScottUSA, CT · May 14, 2013#14 Originally Posted by
cali yaris ↑ We only have one set of instructions posted, for the aftermarket round switch. They would not be correct for the rectangular switch we used to include (a big reason was because of the modification needed on the switch)
Garm,
He was following the original kit instructions (the set prior to mine).
CTScottUSA, CT · May 14, 2013#15 Originally Posted by
swidd ↑ So for option 6 b, fog lights on with low, high and park:
I will be plugging both wires from the switch into 13 and 3? But 3 doesn't connect to anything...
Am I supposed to just remove the wires that are in there already, and leave them hanging unconnected?
Into the original Yellow wire 3 (you will put it back as it was when you started and then tap one of the switch wires to it and the other to the wire in pin 13).
swiddThread starterCentral Alabama, GOD BLESS AMERICA · May 14, 2013#16So I have to remove the ends of the switch's wire and just tap 3 and 13... Okay :-)
I really didn't understand that from reading the manual. I'm not a smart man :-/
CTScottUSA, CT · May 14, 2013#17 Originally Posted by
swidd ↑ So I have to remove the ends of the switch's wire and just tap 3 and 13... Okay :-)
I really didn't understand that from reading the manual. I'm not a smart man :-/
There was always much confusion on that. It means that you need to split the switch's harness all the way to the switch, so that there are four completely separate wires, and then you need to extend some of them to reach where they need to go.
swiddThread starterCentral Alabama, GOD BLESS AMERICA · May 14, 2013#18Now you just confused me even more. There's three wires coming out of the switch socket.
Black (which I grounded)
Green (in picture)
Red (in picture).
Where does each go? If I want to ignore the switch light and just have functional fog lights, can I stick with the instructions in 6(b) and just merge green and red to 3 and 13? And leave black grounded?
CTScottUSA, CT · May 14, 2013#19 Originally Posted by
swidd ↑ Now you just confused me even more. There's three wires coming out of the switch socket.
Black (which I grounded)
Green (in picture)
Red (in picture).
Where does each go?
It depends on there position in the switch connector. There should be four wires entering the green connector.
swiddThread starterCentral Alabama, GOD BLESS AMERICA · May 15, 2013#20I'll have to take it apart tomorrow and see. I only found three wires.
CTScottUSA, CT · May 15, 2013#21To explain this a bit better, here is a top and bottom view of an open switch with the connector plugged in:
Picture not included in this copy1 attachment not included in this copy
swiddThread starterCentral Alabama, GOD BLESS AMERICA · May 15, 2013#22Okay,.. so there are four wires going into the switch. But I only found two coming out of the harness + the ground wire. The other one must be hidden inside the harness or be merged with the red/yellow wire coming out. As I put it back together already, I'm too lazy to take it apart to check, unless it really becomes necessary. It's so hot outside...
http://i.imgur.com/MmYoWzs.jpg http://i.imgur.com/AmcxmpE.jpg The good news is that the fog lights are working, and the switch is working.
The bad news is that, at least as far as I can tell in super bright sunlight, the switch illumination is still on with the ignition off.
I guess I can snip the "third" red wire, i.e. the one next to the grounding wire, to resolve this issue? I don't really need switch illumination or dash light; when it's dark I can tell by looking where I'm supposed to be looking while driving, to tell if they're on.
CTScottUSA, CT · May 15, 2013#23 Originally Posted by
swidd ↑ Okay,.. so there are four wires going into the switch. But I only found two coming out of the harness + the ground wire. The other one must be hidden inside the harness or be merged with the red/yellow wire coming out. As I put it back together already, I'm too lazy to take it apart to check, unless it really becomes necessary. It's so hot outside...
http://i.imgur.com/MmYoWzs.jpg http://i.imgur.com/AmcxmpE.jpg The good news is that the fog lights are working, and the switch is working.
The bad news is that, at least as far as I can tell in super bright sunlight, the switch illumination is still on with the ignition off.
I guess I can snip the "third" red wire, i.e. the one next to the grounding wire, to resolve this issue? I don't really need switch illumination or dash light; when it's dark I can tell by looking where I'm supposed to be looking while driving, to tell if they're on.
The reason the light is still on is that the lighting and switching circuits are bridged. In order to separate them, you have to split all four wires apart.
swiddThread starterCentral Alabama, GOD BLESS AMERICA · May 16, 2013#24Snipped wire, and nothing exploded. Now everything works perfect.
Thanks ctscott!!