Yarisworld Archive

transmission oil seal

43 posts · 25,852 views

kc0rpmOriginal postDecherd, TN · Mar 21, 2013#1
Does anybody know what the part number is for the drivers side axle oil seal on an 08 yaris sedan is? I can't seem to find anything online and my local dealer is not being very helpful. Thanks in advance. This forum is awesome.

Replies 42

CTScottUSA, CT · Mar 21, 2013#2
Left Side:
Automatic: 90311-34030
Manual: 90311-25028

Right Side:
Automatic: 90311-34031
Manual: 90311-34033
kc0rpmThread starterDecherd, TN · Mar 21, 2013#3
Awesome. You wouldn't happen to know where I could get the left my one online would you?
kc0rpmThread starterDecherd, TN · Mar 21, 2013#4
Oops, I meant left manual transmission
kc0rpmThread starterDecherd, TN · Mar 21, 2013#6
Hmm...the only thing I see on there is an output shaft seal. Don't think that's what I'm looking for.
fnkngrvIn The Hotbox · Mar 21, 2013#7
This is what they list for the Manual Tranny that they carry:

2008 : TOYOTA : YARIS : 1.5L L4 : Transmission-Manual

Clutch Hydraulic Hose
Clutch Kit
Clutch Master Cylinder
Clutch Release Bearing
Clutch Slave Cylinder
Input Shaft Repair Sleeve
Input Shaft Seal
Output Shaft Repair Sleeve
Output Shaft Seal
Shift Shaft Seal
Transmission Mount

Can you further identify what part you have to replace or that is non-funtional? Mayhaps even a photo or two?
CTScottUSA, CT · Mar 21, 2013#8
For OEM parts, TRDSparks.com or Toyotapartszone.com are the two I use.
kc0rpmThread starterDecherd, TN · Mar 21, 2013#9
Thank you Scott. Toyotapartszone had exactly what I was looking for.
kc0rpmThread starterDecherd, TN · Apr 7, 2013#10
So I ordered the left seal for the manual trans with the number above and after tearing my car apart it isn't even close to what I jeeded . what gives?

Picture lost · i796.photobucket.comthis is what I got
Picture lost · i796.photobucket.com and this is what the old one looks like
kc0rpmThread starterDecherd, TN · Apr 7, 2013#11
Here is a better size comparison.

Picture lost · i796.photobucket.com
CTScottUSA, CT · Apr 7, 2013#12
The part you received is the actual axle seal, which keeps the fluid in. The outer part in your picture is the "dust cover" and is: 41336-12010
kc0rpmThread starterDecherd, TN · Apr 7, 2013#13
Ok, so how do I go about removing the dust cover without damaging it? There doesn't seem to be anything in the service manual about it.
CTScottUSA, CT · Apr 7, 2013#14
Originally Posted by kc0rpm ↑
Ok, so how do I go about removing the dust cover without damaging it? There doesn't seem to be anything in the service manual about it.
That is a very good question. I think a seal puller would be the right tool. I had a damaged one that I had to replace (and didn't have a set of seal pullers) and I completely chewed it up trying to get the bad one out.
kc0rpmThread starterDecherd, TN · Apr 7, 2013#15
All I have is a slide hammer and an old Mac seal puller. I wonder if pulling the inner seal and the dust cover as one unit would work. I just don't want to mangle that dust cover and have to wait for another part to come in.
kc0rpmThread starterDecherd, TN · Apr 8, 2013#16
OK, now this is starting to get frustrating. The only thing that is in that hole is what you call a dust cover
Picture lost · i796.photobucket.com
This little seal that I have doesn't appear anywhere. What gives?
kc0rpmThread starterDecherd, TN · Apr 8, 2013#17
Ok, so from what I can figure out the dust cover is actually part of the axle, not attached to the transmission. What I pulled out is the actual oil seal so the part that I have is not what I needed. Im not sure where it goes but I'm guessing that its either the input shaft or output shaft which is not what I am looking for so i guess its another trip to the dealer and wait another day for the correct part. Will post correct part number when I figure it out.
CTScottUSA, CT · Apr 8, 2013#18
It has been over 3 years since I did mine, and it was on an automatic. I am going by the electronic parts catalog. Here are the diagrams that I got the part numbers from:

MTM - Seals 2.jpg

MTM - Dust Cover.jpg
CTScottUSA, CT · Apr 8, 2013#19
Here is one other possibility for those seals. The kit of seals in the bottom part of this image is 04331-52520 (Gasket kit, transaxle overhaul, MTM)


MTM - Seal Kit.jpg
kc0rpmThread starterDecherd, TN · Apr 8, 2013#20
Not quite sure what the number is on the part the dealer just ordered but I will know tomorrow when I pick it up.
kc0rpmThread starterDecherd, TN · Apr 8, 2013#21
Now I just have to figure out how to drive that seal in with out damaging it. The lip sticking out of it makes it impossible with my standard seal drivers.
CTScottUSA, CT · Apr 8, 2013#22
Originally Posted by kc0rpm ↑
Now I just have to figure out how to drive that seal in with out damaging it. The lip sticking out of it makes it impossible with my standard seal drivers.
Toyota makes a SST (09309-37010) for installing them. I machined a chunk of Oak to insert mine.

SST Seal.jpg
kc0rpmThread starterDecherd, TN · Apr 8, 2013#23
Yeah, I just chucked my largest seal driver up on the lathe and cut down the center to clear the flange
kc0rpmThread starterDecherd, TN · Apr 9, 2013#24
The correct part number for the left axle seal is 90311-34044
CTScottUSA, CT · Apr 9, 2013#25
Originally Posted by kc0rpm ↑
The correct part number for the left axle seal is 90311-34044
That's interesting. That part number shows in the EPC as only being for the Scion xB.
kc0rpmThread starterDecherd, TN · Apr 9, 2013#26
Hmm... Well we found it on the epc. Took a lot of digging though and it is most certainly the right part. It matches up exactly with what I pulled.
kc0rpmThread starterDecherd, TN · Apr 9, 2013#27
OK, looks can be deceiving. I am inclined to believe that you are correct and that part number is for an Xb as it is at least half an inch too small in diameter.
CTScottUSA, CT · Apr 9, 2013#28
Originally Posted by kc0rpm ↑
OK, looks can be deceiving. I am inclined to believe that you are correct and that part number is for an Xb as it is at least half an inch too small in diameter.
It's absolutely amazing that finding a simple part could be so hard.

Does this look correct for the measurements?
Shaft Size: 1.378 in. (35 mm.)
Housing Bore: 2.48 in. (63 mm.)
Outside Diameter: 2.491 in. (63.28 mm.)
Width: 0.394 in. (10 mm.)
kc0rpmThread starterDecherd, TN · Apr 9, 2013#29
Originally Posted by CTScott ↑
It's absolutely amazing that finding a simple part could be so hard.
Yeah, no kidding. I was forced to put the old seal back in as I have to have the car back on the road. I'm just hoping it doesn't leak too bad as putting that old seal back in is probably the worst option. On another note I do have to say that royal purple gear oil is like night and day compared to the cheap stuff.
kc0rpmThread starterDecherd, TN · Apr 10, 2013#30
Well after another trip to the dealer we shall see what we receive tomorrow. Hopefully it is the right part as I about at my wits end with this seal but now I don't have a choice but to replace it. Stupid car repairs are never as simple as they should be.
ezhacker1San Francisco · Apr 11, 2013#31
This is definitely my kind of thread (same problem I am having with needing to replace it)

Are you leaking oil much? I loose nearly quart in 6 months!. Iv just been keeping an eye on it and refilling. How easy is it to DIY? Read through thread that i need to have some tools tho...
YarisSedanCalifornia - Bay Area · Apr 11, 2013#32
The part number you need is 90311-34042 for the left and 90311-34023 for the right Ishino makes it, it should be available at any local parts store not just the dealer. If you still cant get it let me know I have 5 in stock they are about 5 dollars each. (happen to work at a transmission shop)
ezhacker1San Francisco · Apr 11, 2013#33
so its this then?
Picture lost · img.plentycar.ru
YarisSedanCalifornia - Bay Area · Apr 11, 2013#34
Hah yup thats it
kc0rpmThread starterDecherd, TN · Apr 11, 2013#35
That may be it but I am very hesitant to say for sure as the on for the xb looks identical but just a little smaller than the yaris one
kc0rpmThread starterDecherd, TN · Apr 11, 2013#36
Originally Posted by ezhacker1 ↑
This is definitely my kind of thread (same problem I am having with needing to replace it)

Are you leaking oil much? I loose nearly quart in 6 months!. Iv just been keeping an eye on it and refilling. How easy is it to DIY? Read through thread that i need to have some tools tho...
I wasn't leaking a lot but I hate leaks and got tired of seeing it every time I changed the oil and inspected the CV boots.

As for diy its not too terribly difficult but a couple of specialty tools are nice and one may be absolutely necessary. A slide hammer is one of the tools that makes the job a lot easier for both removing the axle and removing the seal. The tool that I found I couldn't do the job without was a ball joint seperator such as this http://www.harborfreight.com/automot...tor-99849.html. A simple pickle fork will only destroy the boot and there is not enough clearance between the ball joint and axle for anything else. I tried a similar tool to the harbor freight that I found at a parts store but it wouldn't fit between the bolt and axle.
kc0rpmThread starterDecherd, TN · Apr 11, 2013#37
Oh yeah, a 19mm crows foot. Can't torque the ball joint without one. I found that mine had dissapeared and had to borrow one from the neighbor
kc0rpmThread starterDecherd, TN · Apr 11, 2013#38
And as for parts stores having that seal, I can't even get a damn axle nut outside the dealer. My local parts stores carry nothing for the yaris except plugs, filters, and a special order axle. That's about it.
YarisSedanCalifornia - Bay Area · Apr 11, 2013#39
Originally Posted by kc0rpm ↑
And as for parts stores having that seal, I can't even get a damn axle nut outside the dealer. My local parts stores carry nothing for the yaris except plugs, filters, and a special order axle. That's about it.
Dang forgot its different for other people who don't live in the bay area. Where I live theres probably about 35 part stores within a 20 mile radius. If you go to the dealer with the part numbers i listed then they should be able to get you the right part then no problem. Otherwise if you want to paypal me 5 bucks I can put one in a envelope with a stamp on it and send it your way.
kc0rpmThread starterDecherd, TN · Apr 11, 2013#40
Well I have a part sitting at the dealer right now just wasn't able to make it there today. Hopefully I will have more time tomorrow and we will see if the numbers match up.
CTScottUSA, CT · Apr 11, 2013#41
Originally Posted by YarisSedan ↑
The part number you need is 90311-34042 for the left and 90311-34023 for the right Ishino makes it, it should be available at any local parts store not just the dealer. If you still cant get it let me know I have 5 in stock they are about 5 dollars each. (happen to work at a transmission shop)
From the EPC, I never would have guessed that 90311-34042 was that seal. 90311-34023 does make sense from the diagram though.

90311-34023
90311-34023.jpg

90311-34042
90311-34042.jpg
MGBball11Phoenix, AZ · Jun 10, 2015#42
Sorry if it's bad manners to resurrect a 2-year-old post. I'm a complete car novice, and a friend of mine is going to help me with a few repairs recommended by a local shop. I was told one of my output shaft seals is leaking. Should I get the parts mentioned by YarisSedan (90311-34042 for the left and 90311-34023 for the right)? I got a bit confused by the discussion about the dust cover versus the actual seal. Do I need to get both?

Any help would be appreciated!
CTScottUSA, CT · Jun 10, 2015#43
Originally Posted by MGBball11 ↑
Sorry if it's bad manners to resurrect a 2-year-old post. I'm a complete car novice, and a friend of mine is going to help me with a few repairs recommended by a local shop. I was told one of my output shaft seals is leaking. Should I get the parts mentioned by YarisSedan (90311-34042 for the left and 90311-34023 for the right)? I got a bit confused by the discussion about the dust cover versus the actual seal. Do I need to get both?

Any help would be appreciated!
Correct - The parts listed by YarisSedan are the correct ones.