Yarisworld Archive

2NZ-FE, What would you do?

19 posts · 20,549 views

Ryze268Original postAntigua & Barbuda · Mar 17, 2013#1
As the title asks, I just wanted to know if you guys were stuck withan automatic 2NZ-FE 3 Door Vitz what would you do?

Rules:

Selling it is out of the Question 👎
Engine Swap is out as it is too costly


Goal:

At least 120 ps 👍

Budget $1000 USD

Yes, I am secretly asking this to explore my own tuning options

Replies 18

tooterLos Angeles · Mar 17, 2013#2
I'd just do a few low cost bolt-on's like this...🙂

Picture not included in this copy

...and a loud muffler.

Your car won't be fast,
but it will sound fast. 😉
bebeeloStockton, CA · Mar 18, 2013#3
short ram intake - $80~$180
cold air intake - $150~$250
racing headers - $150~$260
axle-back exhaust - $280~$360
cat-back exhaust - $450~$550
Garm's intake manifold ~ $700

lol this is probably a +10 -15 ish hp gain with headers intake and exhaust and intake manifold.
GolddeenohColumbia, SC · Mar 18, 2013#4
it is a 2NZ-FE so i'm not really sure that the intake manifold will even bolt on.
tooterLos Angeles · Mar 18, 2013#5
Originally Posted by Golddeenoh ↑
it is a 2NZ-FE so i'm not really sure that the intake manifold will even bolt on.
I think it might just bolt right onto the 2NZ head... 👍
Looking at the 2NZ FE specs showed that it's the same bore as a 1NZ with only a shorter stroke. Under the hood clearance of other components is an unknown, but could easily be determined with some careful measurements. Even that exhaust header pictured above is listed as fitting both 1.3 and 1.5 engines.
Ryze268Thread starterAntigua & Barbuda · Mar 18, 2013#6
I'm glad I came to this site, you guys are legit =D

I have been looking around but I can't seem to find any headers, it also sounds like I should visit my local fab shop as decats are legal where I live
ViperoniBrampton, ON · Mar 18, 2013#7
Save up for a supercharger.
junorico24Sydney · Mar 20, 2013#8
Leave it as is. It's meant to be a granny mobile. Nah.. Seems to me the common mods are ; 1zz throttle body, spacer and garms intake manifold.
yariseggvvtiCali · Mar 21, 2013#9
Upgrade your suspension and smoke fast vehicle in to the turns. They brake in the turn and your gas exit the turn.
Ryze268Thread starterAntigua & Barbuda · Mar 21, 2013#10
Yes, definitely won't ignore the suspension and I don't see my Vitz as a 'granny mobile' =P
Ryze268Thread starterAntigua & Barbuda · May 1, 2013#11
Would it be possible to stroke the 2nz to a 1.5? If possible how would I go about doing it?
thebarberGrand Rapids, MI · May 3, 2013#12
Just get 1nzfe crank/listless/rods

But just get coilovers and tires...
Ryze268Thread starterAntigua & Barbuda · May 3, 2013#13
Originally Posted by thebarber ↑
Just get 1nzfe crank/listless/rods

But just get coilovers and tires...
listless or pistons?
thebarberGrand Rapids, MI · May 4, 2013#14
Pistons...auto correct
Ryze268Thread starterAntigua & Barbuda · May 12, 2013#15
^ It's that easy? If yes I'm definitely going to do it =D
cali yarisCanoga Park, CA · May 12, 2013#16
Doesn't the NCP10 use xA/xB peripherals, like cable throttle?
Ryze268Thread starterAntigua & Barbuda · Aug 3, 2013#17
Originally Posted by cali yaris ↑
Doesn't the NCP10 use xA/xB peripherals, like cable throttle?
you are indeed correct
marion2Manila, PH · Nov 16, 2014#18
Originally Posted by thebarber ↑
Just get 1nzfe crank/listless(piston)/rods

Do I have to do something like balance it before installing it on my 2nz-fe engine? I mean are they interchangeable like a replacement to my previous crank , pistons, connecting rods?
japleKuala Lumpur, Malaysia · Nov 16, 2014#19
read my thread a few threads below.... called my dyno run