junorico24Original postSydney · Mar 2, 2013#1OK so I changed the belt . I tightened it up, but have a squealing at idle. It goes away at cruising speed when the car is running. When the car is running it's fine.But it randomly comes back at idle, not always but it squeals when i come to a full stop.It doesn't always do it. I have the crappy dayco brand belt.
HELP...
😎
Replies 19
CTScottUSA, CT · Mar 2, 2013#2Typically that means that it either is still not tight enough, or that while it was initially squealing the contact surface of the belt glazed (where the friction of it slipping caused the surface to melt enough to become too smooth to grip on the pulleys).
I have a Dayco belt on my red Yaris, that I grabbed because it was the only thing in stock at the store that I grabbed it from. I have had to tighten it three times since the initial installation.
junorico24Thread starterSydney · Mar 2, 2013#3 Originally Posted by
CTScott ↑ Typically that means that it either is still not tight enough, or that while it was initially squealing the contact surface of the belt glazed (where the friction of it slipping caused the surface to melt enough to become too smooth to grip on the pulleys).
I have a Dayco belt on my red Yaris, that I grabbed because it was the only thing in stock at the store that I grabbed it from. I have had to tighten it three times since the initial installation.
The belt stopped squealing for now. My only concern is if the alternator charging the new battery. I hope i have the right tension.
Thanks Scotty mate.
hw6515U.S · Mar 2, 2013#4Though the proper tension is required, did you check the pulleys for damage?
Specially the water pump one, I found mine damaged while replacing the belt.
If you used WD-40 in the alternator lower bolt, I suggest spraying the area with a mild degreaser then flush it with water.
junorico24Thread starterSydney · Mar 2, 2013#5Yeah, my water pump pulley is glazed it looks like that pic.Thanks for the info
man. How much does a new one cost?
hw6515U.S · Mar 2, 2013#6hw6515U.S · Mar 2, 2013#7Yeah the pic is not good, but is not glaze, the belt wore the finish and scored the pulley noticeably.
This is a pic of the new one.
junorico24Thread starterSydney · Mar 3, 2013#8Yeah, good idea. Pry bar the thing tight. I tried to pull it real tight. But it still squeals.
junorico24Thread starterSydney · Mar 4, 2013#9 Originally Posted by The Critic ↑
Some glazing is normal. It is hard to tell from that picture due to the reflection.
I just installed a Dayco 5040465 today and had no problems at all.
From past experience, it is not uncommon for aftermarket belts to stretch a bit more than the OE belts. Therefore, it may be necessary to tighten them a
hair tighter than required. The revised spec for the 2007 Yaris is 10-11mm (used belt), not the 11-14 that the manually originally specifies. Since you are using an aftermarket belt, I would tighten it a bit tighter...probably 7-10mm.
This is how I tightened it: use a prybar and pry HARD between the engine mount and the
reinforced area on the alternator. If you look in this post, the "reinforced area" that I am referring to is the rounded area that sort of sticks out:
Easy fix for Squeaky / Squealing Belt If you use a very long prybar (24") and pry hard against the areas I mentioned, while still holding your prybar, fully tighten the 12mm bolt at the top of the alternator. This should fully secure the alternator in the position that you desire. Then f/u by tightening down 14mm bolt at the bottom.
If you do this with a new belt, the belt should have very little deflection. After the 10-15 min run time, you should feel a small amount of deflection (7-10mm) which is just a hair tighter than what Toyota suggests...and your noise should go away.
Thanks so much man...The reinforced area is left side of the bracket near the belt side?
UberSilverAlameda,Ca. · Mar 4, 2013#10 Originally Posted by
junorico24 ↑ Yeah, my water pump pulley is glazed it looks like that pic.Thanks for the info
man. How much does a new one cost?
rockauto has them for $33.
junorico24Thread starterSydney · Mar 5, 2013#11Pry bar ftw..It seemed to do the trick.Success! Thanks critic..
jpmck03USA · Mar 5, 2013#12 Originally Posted by
CTScott ↑ ... I have a Dayco belt on my red Yaris, that I grabbed because it was the only thing in stock at the store that I grabbed it from. I have had to tighten it three times since the initial installation.
^ That's been my problem... Apparently Dayco belts are like rubber bands, they love to stretch! I think I've had to tighten mine about 3 times so far as well. 😢
harda toenailSE Missouri · Mar 10, 2013#13Toyota installed a new one on mine when I brought it in for a water pump. I had to tighten it a week later
bankrobberCentral Florida · Mar 13, 2013#14Same problem here. I installed a new Dayco belt from AutoZone because it was lifetime warranty. Within a few weeks it started slipping at start up. I was lazy and let it go awhile. I finally tightened it and have had to tighten several more times. Starting to slip again. I will never buy a Dayco belt again. I will probably replace it with a belt from toyota soon
yaris4062007northern california · Mar 14, 2013#15Only yaris has this problem :(. My other cars never had this problem. I have changed twice with new belts it squeaks alot ;(
yaris4062007northern california · Mar 14, 2013#16How do i retighten the belt, anyone have picture?? Ty
junorico24Thread starterSydney · Mar 14, 2013#17 Originally Posted by
yaris4062007 ↑ How do i retighten the belt, anyone have picture?? Ty
Ah...get a pry bar or anything solid wedge it between the reinforced part of the alternator and engine mount all you have to do then is pull the pry bar toward you until there's only a hair line of deflection on the belt. You can get someone to tighten the bolt whilst you pull the pry bar towards you.It's easy! don't damage that pipe on the side when you tighten it. Hope this helps.
Picture lost · i825.photobucket.com See the gap between the alternator and down the bottom is the engine mount. Just put a pry bar in between then pull hard on it.
yaris4062007northern california · Mar 15, 2013#18Ty :)
jpmck03USA · Mar 16, 2013#19 Originally Posted by
bankrobber ↑ Same problem here. I installed a new Dayco belt from AutoZone because it was lifetime warranty. Within a few weeks it started slipping at start up. I was lazy and let it go awhile. I finally tightened it and have had to tighten several more times. Starting to slip again. I will never buy a Dayco belt again. I will probably replace it with a belt from toyota soon
I swapped out the belt on our Corolla because it was about that time (70k and starting to chirp on startup and under load). So, I got two Dayco belts and did them... mine started squealing after a few months, and the Corolla, which has a fully functional automatic tensioner is doing the ol' slipping belt chirp song already!
Never again, Dayco. Never again. 👎
metalsharkMesa, AZ · Mar 29, 2013#20Today I installed a new belt from the Toyota dealer on my '08 Yaris. The Toyota belt has a fuzzy fabric type surface on the Vees side of the belt. My car still makes the bad bearing noises. Using a Harbor Freight stethoscope I checked the water pump bearings, the alternator bearings and the AC clutch hub bearing. They were all loud but the water pump was the worst of the three. It's not leaking......yet. $23.04 delivered from Rockauto.com. Does anyone know where to pick up new bearings for the alternator?