Yarisworld Archive

Rims size question

9 posts · 6,189 views

KamikazeOriginal postRome, Italy · Jan 29, 2013#1
Hi everyone, I'm absolutely a tires/rims size newbie! be kind with me! 🙁
I use the stock tires size (185/55/R15) and wheel spacers (16mm front/20mm rear) on my '02 TS.
I'd like to buy a set of Rota RB, 15x8 4x100mm ET30, can I fit those on my car without rolling the fenders?

thank you so much!

Replies 8

DeathBeardLos Angeles, CA · Jan 30, 2013#2
Is your car lowered
tooterLos Angeles · Jan 30, 2013#4
Originally Posted by Kamikaze ↑
Hi everyone, I'm absolutely a tires/rims size newbie! be kind with me! 🙁
I use the stock tires size (185/55/R15) and wheel spacers (16mm front/20mm rear) on my '02 TS.
I'd like to buy a set of Rota RB, 15x8 4x100mm ET30, can I fit those on my car without rolling the fenders?

thank you so much!
I think that Rota RB's are just about the most beautiful wheels made. Molto bella! 🤤

Picture not included in this copy

And I understand your situation, because I also was blindsided by the width/offset unknowns so I stayed closer to stock and am running 15X7 +35's and 195/65 tires with no rubbing at stock height. the front wheels are just barely under the edge of the fender so if the car was lowered, it would likely rub. This is because Rota's have a wide machined edge outside of the spokes like the old fashioned wheels used to have. Thst's why they look so distinctive.

Picture not included in this copy

Notice that the new style front wheel drive rims usually have none and so more easily tuck under fenders on lowered cars.

I did discover that with the +35's I needed to add 5mm spacers to allow the front wheels to clear the disc brake calipers. If you run +30's that shouldn't be an issue, because they get the wheels to position closer to the center of the vehicle by machining the inside surface that bolts onto the hubs. That's where the reduced brake clearance comes from.

Please post pics when you get them! 🙂
ilikericesavannah, ga · Jan 30, 2013#5
Not a fan of those rotas. Again its all opinions. I did not have that issue with my rota gt3's and they are a +40 offset. It must be an RB only issue. Also keep in mind op has an 2002
tooterLos Angeles · Jan 30, 2013#6
Originally Posted by ilikerice ↑
Not a fan of those rotas. Again its all opinions. I did not have that issue with my rota gt3's and they are a +40 offset. It must be an RB only issue. Also keep in mind op has an 2002
I think it's because the RB's are replicas of the 1960-70's era Panasport racing wheels when deep dish was the norm on RWD cars.
Picture not included in this copy

Enkei also made that same style in the 1980's.
YaristeveLos Angeles · Jan 30, 2013#7
Originally Posted by tooter ↑
Enkei also made that same style in the 1980's.
They're back; they added the Compe8 to their retro line of wheels.
tooterLos Angeles · Jan 30, 2013#8
Wow... they do.
Oooh... nice! 🤤

Picture not included in this copy
KamikazeThread starterRome, Italy · Feb 1, 2013#9
Thanks everyone for your answers!

Originally Posted by DeathBeard ↑
Is your car lowered
yes it is, TA Technix shocks+springs -40mm