Yarisworld Archive

Megan Coilover Install and Tips

17 posts · 3,708 views

DeathBeardOriginal postLos Angeles, CA · Nov 20, 2012#1
Hey all,
hopefully this will be beneficial to those out there wanting to install these coilovers. The directions from Megan are a joke..Please note I take no responsibility for this install and don't claim to be a professional.. This is not a step by step diy, just simply showing you how the megans are assembled.

Replies 16

DeathBeardThread starterLos Angeles, CA · Nov 20, 2012#2
#1- This is the most useful tool in my box, it's a craftsman offset box wrench, 17mm on one side and 19 on the other..This will save you alot of time on having to remove the windshield wiper assembly, simply bypass all the drama..

1 attachment not included in this copy

DeathBeardThread starterLos Angeles, CA · Nov 20, 2012#3
#2- I got these from ebay, they support the car without messing up the pinch welds, was sick of using hockey pucks, worth every penny.

1 attachment not included in this copy

DeathBeardThread starterLos Angeles, CA · Nov 20, 2012#5
#3-There are already plenty of other useful threads on how to take the struts out, I am assuming you have already done this..The following photos show how to assemble the megans..I found that the strut bearing does not fit in the megan supplied red piece, so I just put over it, I ended up using ALL of the OEM pieces..

3 attachments not included in this copy

DeathBeardThread starterLos Angeles, CA · Nov 20, 2012#6
#4- When you reinstall the front on any mcpherson car you MUST LOAD THE SUSPENSION before you tighten the bolts. You can see that before tightenting the 19mm bolts the suspension is loaded

1 attachment not included in this copy

DeathBeardThread starterLos Angeles, CA · Nov 20, 2012#7
#5- Here is a comparison of the Toyota OEM camber bolt on top vs the stock on the bottom..These are so awesome and superior in every way to the ingalls spc type

1 attachment not included in this copy

DeathBeardThread starterLos Angeles, CA · Nov 20, 2012#8
#6--Front is done and moving to the back..Like others have mentioned the rear Megan spring is simply not low enough, I will be removing the spring perches.. Before

1 attachment not included in this copy

DeathBeardThread starterLos Angeles, CA · Nov 20, 2012#9
#7--And after! No more Megan spring perches and MUCH lower..I lowered the shock by 1" securing the spring in place.. I have no finger gap and the top of the tire is slightly tucked now

1 attachment not included in this copy

DeathBeardThread starterLos Angeles, CA · Nov 20, 2012#10
Enjoy your coilovers

1 attachment not included in this copy

DeathBeardThread starterLos Angeles, CA · Nov 20, 2012#11
I just drove it around the block and the springs have settled rear tires are fully tucked..and my rear end scrapes like a mofo on my driveway
1.5Tampa · Nov 20, 2012#12
Nice you got way lower than I could on the sedan. Great write up, way better than mine lol
yarisugiハワイ · Nov 20, 2012#13
Originally Posted by DeathBeard ↑
#5- Here is a comparison of the Toyota OEM camber bolt on top vs the stock on the bottom..These are so awesome and superior in every way to the ingalls spc type
You mean aftermarket on bottom, right?
DeathBeardThread starterLos Angeles, CA · Nov 20, 2012#14
as in the top is Toyota oem camber bolt and the bottom is toyota oem standard bolt
yarisugiハワイ · Nov 20, 2012#15
Thanks! Weird, I'd thought the bottom would be the better one since it looks more robust.
DeathBeardThread starterLos Angeles, CA · Nov 20, 2012#16
it has to be skinnier to acheive negative camber
1.5Tampa · Nov 20, 2012#17
The size difference creates the camber I believe because it angles the spindle.

I had no idea Toyota made camber bolts. I have ingalls.