Yarisworld Archive

Belt noise after MI pulley?

32 posts · 10,870 views

Captain SlowOriginal postScott, LA · Nov 20, 2012#1
I've got some belt noise after doing the MI pulley. Not squeal, just an audible (windows down sitting in car) sound of the belt spinning around. Is this just a quality of the lighter pulley or should I have my belt checked again? I've never done a lightweight crank pulley before and wanted to make sure this wasn't normal before I started poking around.

Replies 31

cali yarisCanoga Park, CA · Nov 20, 2012#2
I would check your belt tension but it shouldn't make more audible noise.
tooterLos Angeles · Nov 20, 2012#3
Originally Posted by cali yaris ↑
I would check your belt tension but it shouldn't make more audible noise.
That raises a question... is there any such thing as inaudible noise? 😉
DJYojimboChicago · Nov 20, 2012#4
Can u record the video? Maybe Garm can confirm if its normal or not
GolddeenohColumbia, SC · Nov 20, 2012#5
Originally Posted by tooter ↑
That raises a question... is there any such thing as inaudible noise? 😉
Audible just means that it can be heard by human ears, so yes there are inaudible noises, and dogs can hear sounds we can not.
cali yarisCanoga Park, CA · Nov 20, 2012#6
^ My wife arguing with me, for example.
tooterLos Angeles · Nov 20, 2012#7
Originally Posted by cali yaris ↑
^ My wife arguing with me, for example.

😆

My wife says I have selective hearing.
jpmck03USA · Nov 20, 2012#8
Originally Posted by tooter ↑
😆

My wife says I have selective hearing.
😆 You, too?
GolddeenohColumbia, SC · Nov 20, 2012#9
apparently i have a some hearing difficult in my right ear, typically that is the side were my wife tends to be when she is asking me something and i get to look over at her while she gives me the stare of death while i have not the slightest clue as to what she said.
Captain SlowThread starterScott, LA · Nov 27, 2012#10
i will record some audio of it later. it's definitely audible though.
1.5Tampa · Nov 27, 2012#11
Are there any cracks in the belt? Time to replace?

This thread went from drive belt noise to ignoring complaining women lol
tooterLos Angeles · Nov 27, 2012#12
My thought is that it could possibly be the anodized surface on which the belt runs which is relatively slippery compared to a raw aluminium surface. If it was me, I'd remove it, mask it off with some tape and beadblast just the belt grooves alone, although lately my solution to everything has been to blast it. 😆
WeeYariGeorgetown, Ontario, Canada · Nov 27, 2012#13
It's all speculation until an actual audio is made available. I don't believe captain is experiencing any noises associated with slippage, as those are very easily identifiable. Also, belt age should not be an issue since the car is only a 2010.

My thoughts, again speculation, is harmonic. The sound resonating from the MI pulley differs from OEM due to its aluminum vs cast construction. He is probably hearing a different 'whirring' sound.
Captain SlowThread starterScott, LA · Nov 28, 2012#14
Yeah, it's not slippage for sure. Just a different (but noticeably louder) sound at idle. I've got a Zoom H2 and will record and post it up later today.
Captain SlowThread starterScott, LA · Nov 28, 2012#15
I've attached the wav file inside of a zip file.

It's just a high-pitched sound as the belt revolves, kinda annoying.

1 attachment not included in this copy

DJYojimboChicago · Nov 28, 2012#16
Hope Garm can help you with your problem captain! I want to install this pulley too :)
CTScottUSA, CT · Nov 28, 2012#17
Originally Posted by Captain Slow ↑
I've attached the wav file inside of a zip file.

It's just a high-pitched sound as the belt revolves, kinda annoying.
That really sounds like a loose belt to me.
DJYojimboChicago · Nov 28, 2012#18
How many ft lbs is it supposed to be?
CTScottUSA, CT · Nov 28, 2012#19
Originally Posted by DJYojimbo ↑
How many ft lbs is it supposed to be?
There isn't a torque measurement for a belt, but rather a deflection and a tension measurement. They point to check is half way between the alternator and the crank pulley.

Deflection:
New belt 7.0 to 8.5 mm (0.28 to 0.33 in)
Used belt 11 to 13 mm (0.43 to 0.51 in)

Tension:
New belt 539 to 637 N (55 to 65 kg, 121 to 143 ld)
Used belt 245 to 392 N (25 to 40 kg, 55 to 88 ld)
frownonfunRGV, Texas · Nov 28, 2012#20
when i had a loose belt it sounded like there was a pig being slaughtered under my hood. so idk, that doesn't sound so much like a loose belt to me. then again if CT says it does maybe you should listen to him.
frownonfunRGV, Texas · Nov 28, 2012#21
Originally Posted by CTScott ↑
There isn't a torque measurement for a belt, but rather a deflection and a tension measurement. They point to check is half way between the alternator and the crank pulley.

Deflection:
New belt 7.0 to 8.5 mm (0.28 to 0.33 in)
Used belt 11 to 13 mm (0.43 to 0.51 in)

Tension:
New belt 539 to 637 N (55 to 65 kg, 121 to 143 ld)
Used belt 245 to 392 N (25 to 40 kg, 55 to 88 ld)
Yeah it's funny I called my service dept to ask them if they can measure the deflection for me and they said there's no way to measure it. They also said that because there's no tensioner that I wouldn't need to worry, it will tighten itself. I seriously wonder if I should be letting these people do my oil changes, even if it is free.
GolddeenohColumbia, SC · Nov 29, 2012#22
I assume you have already checked to make sure that the belt isn't bottoming out in the groves on the pulleys, that there is not any debris in the pulley groves, and that the pulleys are aligned?
Captain SlowThread starterScott, LA · Nov 29, 2012#23
nope. haven't popped the hood at all. been too busy and it's cold.

figured I'd ask if this was normal before I started poking around. I used to be under a car 5 days a week swapping trannys, replacing front ends, etc... but these days I am not a big fan of doing work myself anymore, lol.
Captain SlowThread starterScott, LA · Feb 3, 2013#24
hey guys, sorry it took me so long to reply to this topic, I've just been busy.

here is a wav file of the sound, about halfway through the idle drops and you can hear it even better. keep in mind that this was taken with the hood closed standing next to the car, not with the recorder in the engine bay.

think it may be time for a new belt or at least a retension on this one? It doesn't do it when I first crank up in the morning but starts 2-3 minutes later (I'm guessing as the belt heats up it expands).

Does the Yaris have automatic tensioners or is it something adjustable? Thanks.

FILE
http://www.filedropper.com/beltnoise
malibuguyWestminster, MD · Feb 3, 2013#25
i had a bad squeal initially. new belt fixed that. now...after about 10,000miles or so...it does a tiny squeak on start up. I looked at the belt, its looks worse then it should for its age. im going to tighten it up a tiny bit more the next time i get a chance.
Black_griffin6Atlanta Georgia · Feb 13, 2013#26
I've been having this same noise. It only happens when I drive the car for a while, and it doesn't happen when you first start the car up.
Captain SlowThread starterScott, LA · Feb 13, 2013#27
^exactly, and it's annoying as hell.
Captain SlowThread starterScott, LA · Feb 15, 2013#28
Just listen to the wav file I attached in an earlier post.
why?harnett county NC · Feb 15, 2013#29
the file in the earlier post is not normal. the filedropper link just goes to the main page, not to a file i can use.

i'd agree with CTScott. I have a full nst pulley set, and after tightening all the belts, i have zero extra noise that sounds anything like that. There is a chance the belt might be too tight as well, but that is a belt noise of some type.
DJYojimboChicago · Mar 25, 2013#30
still having issues with the pulley?
catliektheifLeesburg, VA · Jul 31, 2013#31
@captainslow I'm having the same exact noise after the MI pulley and its driving me INSANE. Did you find a fix?
yougojayEast End · Jul 31, 2013#32
Originally Posted by tooter ↑
😆

My wife says I have selective hearing.
What...? 😆