Replies continued
Ranger SVOAbilene · May 27, 2017#51I just bought
THIS kit on Amazon.
It seems decent and I will be wiring similar to a factory set up. I just made a minor mod to the wiring that came with the lights. The power wire to both lights were spliced together, I cut the splice so that each light is independent of the other. The two wires will be plugged into the underhood fuse panel.
Ranger SVOAbilene · Jun 8, 2017#52OK many aftermarket Fog Light Kits will work with the factory wiring. A few things need to be fixed in the kit I used.
1. The wiring from the right fog light ties into the left. I separated the wires so that each light has its own wires.
2. The Toyota relay is not necessary. A Denso 567-0001 relay is readily available and inexpensive and WILL work.
3. In the directions found here, the aftermarket switch MUST be modified to work with the factory wiring. Simply remove the resistor indicated in the directions. Also in my kit, two of the switch wires were tied together. I separated them. One pair to lighting, the other pair to the headlight switch wiring.
4. The wires to plug into the outside fuse block, any reputable car audio shop can make the ends with the right connector on it.
Fog Lights I used worked perfectly.
Picture lost · i7.photobucket.com
Ranger SVOAbilene · Jun 9, 2017#53OK I want to finish this up.
The wires to plug into the outside fuse block, any reputable car audio shop can make the ends with the right connector on it. In fact, for the two wires with the ends crimped on them was a total of $4.76.
The owner was intrigued. In exchange for explaining exactly what I had done, he loaned me a portable soldering iron, gave me a couple pieces of heat shrink and let me finish it there in his parking lot.
Picture lost · i7.photobucket.com
Anyway its finished and it works
sh0rtlifepacific north WET · Nov 29, 2021#54dead links suck....
just got a "cheep" ebay kit and let me tell you what i got was on par with OE if not better...actual glass lenses, OE switch etc 40$ well spent
after multiple passes thru this site digging for the hookup points on dash etc i eventualy figured it out
David90Nevada · Dec 21, 2021#55 Originally Posted by lespaulstd ↑
I am planning to install a cheap kit in the yaris using the original stalk and relay in the inside part of the car. However, since there is no possibility of getting the adapted harness, could you tell me which kind of pins should be used to connect both lights to pin 1 and 2 in the relay box?
I actually would like to know the same...
CaptamricaSt. Louis Missouri · Jan 2, 2022#56Ok, I bought a new Stalk Switch. I'm just trying to find where the relay is located for my Daughter's 2013 Yaris. The loom connection for the bulbs are there. The fuses are in the fuse boxes that are identified as front Fog Lights. I'll buy whatever the f**k i need to buy for her car to work safely but the link you gave to micro whatever took me to a site when I clicked the Toyota Yaris tab it took me to a Nissan parts manual. Really appreciate a direction to get things for this vehicle. I see buying a Yaris in the Midwest is as bad as buying a Toyota in 1978 with respect to finding documentation on it. Everything is RHD.
At any rate any help would be appreciated. I can't find the damn relay or where it should be.on this 2013. Her 2010 was so much easier.
After reading the entire thread, not realizing it went back several years and rhe Microimage has been closed for years now.
Do I need to short any pins on the Stalk Switch connector? I bought a new switch with the Fog light switch on it for the 2013. It's installed as are a nice set of Fog Lights and Ultra 2 GTR Lighting LED fog light bulbs so I'd really like to get these fired up for her. Just can't seem to find the relay or where it needs to be installed.
CaptamricaSt. Louis Missouri · Jan 2, 2022#57Was hoping to find CTScott was still around since the last post on this thread was in 2016. His PM box has exceeded. It's storage cap so I'm guessing he's not around anymore. Guess I'll figure this out myself. Finding schematics on this vehicle sucks.
mitch9521Red Deer, AB · Jan 9, 2022#58 Originally Posted by
Captamrica ↑ Was hoping to find CTScott was still around since the last post on this thread was in 2016. His PM box has exceeded. It's storage cap so I'm guessing he's not around anymore. Guess I'll figure this out myself. Finding schematics on this vehicle sucks.
I have a 2014 LE and all I had to do was swap out the headlight switch/signal stalk for one with the fog light switch(Mine happened to come out of a 2010 Tundra) and install the fog light assemblies, bulbs and bumper trim pieces. The H11 connectors on my car were just taped onto the crash support behind the bumper cover.
Totally pre-wired, no finding fog light relay nonsense. Even the indicator on the gauge cluster works.
CalrenmanSo. Cal. Ventura · Apr 2, 2022#59 Originally Posted by
Captamrica ↑ Was hoping to find CTScott was still around since the last post on this thread was in 2016. His PM box has exceeded. It's storage cap so I'm guessing he's not around anymore. Guess I'll figure this out myself. Finding schematics on this vehicle sucks.
I am not sure if this will help. A FSM, Chilton's or Hanes manual will help!
https://www.youtube.com/watch?v=drqpznBdnaw KermitAUSAustralia · Jun 5, 2022#60sh0rtlifepacific north WET · Jun 5, 2022#61 Originally Posted by
KermitAUS ↑
both of those are GARBAGE..and good as a backup light on a truck and thats about it
if you want better country lighting get yourself some HID's for the headlights aim for 8000-10,000, and get a matching set of 8000+ for the fog lights, at that point youll never even consider auxillery lighting
my wife has issues with her night vision and we do ALOT of night driving in the winter and its useualy deep out in he country, i tossed in a set of the bellow link and it was litteraly night n day, shes actualy speeding on the country roads instead of holding up traffic, added the fogs and hid'd them and even on the worst of nights visability is NOT an issue
https://www.amazon.com/gp/product/B0...0?ie=UTF8&th=1 KermitAUSAustralia · Jun 11, 2022#62kevinj93Sydney, Australia · Jun 12, 2022#63 Originally Posted by
KermitAUS ↑
HID conversions are allowed in Australia, providing that HID lights were originally available as a factory option on the vehicle. You also have to fit the complete alternate light assembly.
While there are HID conversion kits available that will replace the original H4 globes, they don't match well with the H4 reflectors, and will most likely not focus the light where you want it.
Have you considered an LED light bar? There are brackets available that will fit on the front number plate mount for these.
sh0rtlifepacific north WET · Jun 13, 2022#64i did the h4 swap and they focused beautiffuly on the stock non hid reflectors nothing too high nothing scattered still nice clean edges