Yarisworld Archive

Antho's turbo thread!

15 posts · 9,656 views

packetraceOriginal postQuebec · Aug 24, 2012#1
So some may have read my thread on MI but I wanted to share it here...

So far I have...

SR20DET T25 turbo
1NZ-FE engine
TOGA maine and rod bearing
CP piston 9:1
Highbeam rods
Goldean eagle fuel rail
2AZ-FE injertors
2.5'' intercooler piping kit
ebay CAI for the piping parts to make the piping easier
6AN fuel line with return with 255LPH pump
10an return oil lin
10 an water line
4 an oil feed line

What I am planning for the rest..
AEM GAUGE(thru-boost, water temp, oil pressure from a guy here on YW)
Malibuguy complete exhaust...
Timing chain cover and valve cover powdercoated from TBR with their brand new water pump
TBR complete pulley set
Intake manifold with xB cable TB
MI stainless manifold with heat wrap
Used Tial F38mm external WG
All stainless stud
new thermostat
new dip stick
New gasket(all)

Propably a manual tranny swap...because I am automatic


here are some picture of next component and actual engine

The car!!! But noew has no japanese sticker...
Picture not included in this copy
Engine now..
Picture not included in this copy
Picture not included in this copy
Gauge hole
Picture not included in this copy
The car in the garage
Picture not included in this copy
Fuel rail with TBR extra free fitting and hose that he sent me with this nice fuel rail black powder coated
Picture not included in this copy
Picture not included in this copy
Painted engine
Picture not included in this copy
TBR soon complete pulley set
Picture not included in this copy

Replies 14

pimp my yarischicago · Aug 26, 2012#2
Thats a big project to do all at once. Good luck
thefallsSunny place · Aug 27, 2012#3
This is very tempting. Every time i see someone with a forged build i feel like taking the plunge. But i constantly remind myself that its my daily drive :P

Keep up the good work.

PS: Going overbore or stock bore?
packetraceThread starterQuebec · Aug 27, 2012#4
Originally Posted by pimp my yaris ↑
Thats a big project to do all at once. Good luck
Well the engine has already been running with a turbo...and has been tested on an engine bench test...so this part is no big deal

The rest is just some small stuff to had..

Pulleys new manifold new stud..install gauge...fuel rail....

Powdercoating all lolll

Engine management will be wired before so it makes easier the install
packetraceThread starterQuebec · Aug 27, 2012#5
Originally Posted by thefalls ↑
This is very tempting. Every time i see someone with a forged build i feel like taking the plunge. But i constantly remind myself that its my daily drive :P

Keep up the good work.

PS: Going overbore or stock bore?


You really should do it bro!!
thefallsSunny place · Aug 27, 2012#6
Too early :) engine has only 45k kms. But i have been eyeing that pt tuning short block for a while. If shipping is reasonable then maybe i will splash out.
YodaFL · Aug 27, 2012#7
Originally Posted by thefalls ↑
Too early :) engine has only 45k kms. But i have been eyeing that pt tuning short block for a while. If shipping is reasonable then maybe i will splash out.
^^ Great idea! Wish I went that route 🙁
packetraceThread starterQuebec · Aug 27, 2012#8
Originally Posted by thefalls ↑
Too early :) engine has only 45k kms. But i have been eyeing that pt tuning short block for a while. If shipping is reasonable then maybe i will splash out.
what you mean pt tuning ? got a link ?


When turbo is done I want to build a second engine....but this time...build it my self since this one was bought already built and fuly tested....

I do all that mostly to learn and have fun....it became a passion like 2-3 years ago...

Will pick up a 50k engine...sleeve it...forged pistons and rods...new bearing....new all :D loll

and try a big turbo...with a manual tranny echo ! I really want to try these small car :) Mine is a sedan...
thefallsSunny place · Aug 28, 2012#9
http://www.ptuning.com/subdir/itemde...l&ModelDesc=xB

There you go.

We dont have any workshop which can balance the rotating assembly here. So in future i will just get the short block. Works better this way.
Not too sure what to do about keeping a 8k rev limit.Some use the yaris cup springs.
Need to research a bit on this.
cali yarisCanoga Park, CA · Aug 28, 2012#10
PT tuning, I've only heard really good things about them. We can also build short blocks for West Coasters...
packetraceThread starterQuebec · Aug 28, 2012#11
Originally Posted by thefalls ↑
http://www.ptuning.com/subdir/itemde...l&ModelDesc=xB

There you go.

We dont have any workshop which can balance the rotating assembly here. So in future i will just get the short block. Works better this way.
Not too sure what to do about keeping a 8k rev limit.Some use the yaris cup springs.
Need to research a bit on this.
sounds good....the only thing I dont like is shipping the block to USA from CANADA...where I live...

I really would like to try to build it on my own but its a risky job.....Ill finish turbo first...and see after 😁
packetraceThread starterQuebec · Aug 28, 2012#12
Originally Posted by cali yaris ↑
PT tuning, I've only heard really good things about them. We can also build short blocks for West Coasters...
good to know👍
thefallsSunny place · Aug 29, 2012#13
Indeed this is good news!
packetraceThread starterQuebec · Aug 30, 2012#14
WG flange and gasket ordered*

Manifold from Alex1987 bought

SR20DET turbo from Alez1987 bought

Bought some nice Prosport gauge...thanks to Garm for pointing me these!!

here they are:
Picture not included in this copy
Picture not included in this copy
Picture not included in this copy
YodaFL · Aug 30, 2012#15
well thats pretty. O and got your pm thanks!